Additive Monitoring System User Manual
Contents
1. Pumps Honeywell 07 Nov 08 18 12 12 addsystem Stn01 Supv To reset an injector in alarm login with supervisor or higher access level The alarm reset buttons and injector select drop down boxes then appear To reset an injector alarm Select the injector in alarm in the drop down box and click reset alarms A confirmation dialog then appears BScript Alarm Reset xj A This will send a command to the PCM additve controller to reset all alarms For the selected injector Are you sure Click yes to send to reset alarms command to the additive controller An acknowledge dialog box then appears confirming the action It takes between 15 20 seconds for the alarm to reset in the additive controller and the alarm indicators to clear on the page 8 November 2008 Honeywell Enraf Additive Monitoring System User Manual Page 13 of 24 5 0 Additive Use amp Comparison 5 1 Overview Page gt Station oper Additive Usage AdditiveCompare htm 7 JE l x Main Menu RA DI Daily Totals Additive Flow Daily Compare x Additive Contollers Pump Flow Meters Deviation Shell 3 21 Esso 41 176 Esso 44 100 Esso 6 63 Common User 75 613 Common User 78 300 Common User 3 43 Total Y olume Total Y olume Deviation Shell 13 81 Esso 77 828 Esso 94 800 Esso 17 90 Common User 125 211 Common User 126 500 Common User 1 02 Print Report Deviation Ari Gross Totals Additive Flow Inter2. Enraf Additive Monitoring System User Manual Page 9 of 24 3 4 Alarm Viewer hi Alarms Location View all alarms Date amp Time 09 112 2 31 01 Additive Shell Dery Additive Pump Override Key Switch Additive C U Mogas Additive Severe Deviation Alarm Loading Bay 3 Addi Additive Additive Loading Bay 2 system Additive Controller Gateway Communication Error 09 11 2008 12 11 52 E Unacknowledged alarms Acknowledged alarms D Pause O Resume ay Acknowledge Page Alarms are shown in the alarm viewer until acknowledged or if acknowledged but not cleared There are three severity levels of alarm Urgent severity high severity and low severity The alarm icon on the far left shows the severity level a red square is urgent a yellow triangle is high and a blue triangle is low The severity icons are filled in for present alarms and change to hollow for when the alarm condition clears and is unacknowledged To acknowledge an alarm right click the alarm and select acknowledge To acknowledge all alarms click the Acknowledge Page button on the bottom right of the page High and Urgent alarms trigger an alarm relay in the system control panel which controls an alarm window on the control room annunciator 3 5 Alarm amp Event History All alarms amp events are automatically archived on the system and can be accessed at any time using manager user access level To access the alarm amp even
3. P gt Additive Monitoring System Main Menu Click one of the links below to access a page Additive overview of all PCM additive contralers on site Controllers Ric Additve Usage Additive Pumps System DI system f field comms and network status Status 0 Y AE Main Menu Additive Controllers Additve Use Pumps System Status 3 H vst 07 Nov 08 18 08 53 addsvstem Stn01 Oper The top and bottom navigation bars 1 amp 2 are always visible have the same appearance through out the system The page navigation bar 3 is visible on all pages except the alarm viewer it has links relevant to the current page being displayed and changes from page to page 8 November 2008 Honeywell Enraf Additive Monitoring System User Manual Page 7 of 24 1 Top navigation bar gt Station oper Additive Usage Additi Main Menu 447 ki HF The top navigation bar has a main menu access button and has forward and backward page buttons which operate in the same way as a standard internet web page browser such as internet explorer 2 Bottom navigation bar 3 19 Sep 08 13 01 36 System MBUS1BC ALARM U01 PCM additve controller comms gateway failed ON Honeywell VA 13 08 14 T l experion StnD1 Oper 1 2 4 The bottom navigation bar shows alarm information has access to the alarm viewer and allows operator login 1 System date amp time 2 Alarm s
4. lxi Main Menu RA PA gt Additive Monitoring System Main Menu Click one of the links below to access a page Additive Controllers 3 vith alarm details PCM Vl total additve reset Additve Usage Additive Pumps System On f system field comms and network status Status OF system hardware status Main Menu Additive Controllers Additve Use Pumps System Status 07 Nov 08 18 08 53 I addsystem Stn01 Oper The main menu is displayed after a system start up and can be accessed from the top navigation bar It has access to the two main parts of the system Additive Controllers Access to each additive injector controller on the loading bays showing the same information shown on the additive controller local displays including total injected volume Injector alarm and enable status Additive Usage The daily and gross sum totals of all injected volumes for each additive and a comparison against the flow meter readings for each additive pump There are also links to the pump status page showing pump enable status And the system status page showing diagnostic information for the system 8 November 2008 Enraf Additive Monitoring System User Manual Page 6 of 24 3 2 Navigation There are three methods to navigate around the system 1 Top navigation bar 2 Bottom navigation bar 3 Page navigation bar gt Station oper Main Menu Main htm 4 lel x Main Menu MO
5. 8 11 2008 14 34 00 152 23 154 35 1 37 08 11 2008 14 33 00 149 23 151 67 161 08 11 2008 14 32 00 146 11 147 45 0 91 08 11 2008 14 31 00 231 4 1 Additwe Controllers sum total 2 Flow Meter counter total 3 Deviation The trend window period can be set from 1 minute up to 1 year using the top right drop down box By drawing over the trend graph with the mouse pointer a zoom window can be made allowing easy access to any time window in the past 8 November 2008 Honeywell Enraf Additive Monitoring System User Manual Page 16 of 24 5 5 Bay Detail Page Additive Enraf Monitoring System Bay Additive Use Overview E A lina E ing Day 1 Loading Bay 2 a d DE au Y a m3 aii 2 ading in Y Loading Bay 3 Loading Bay 4 Total Volume Total Volume Total olume i Total Volume Shell 4235 430 Shell 2346 675 Shell 2182 211 Shell 5233 2791 Esso 1937 239 Esso 4325 654 rr GATI r Esso 1827 272 Common User 9867 689 Common User 1253 527 Common User 4538 294 Common User 3725 265 EE O i az a Em Main Menu Additive Controllers Additive Use Pumps This page shows the gross total additive volumes for each loading bay Page navigation bar links Main Menu Additive Controllers overview Additive Use overview Pump status 8 November 2008 Honeywell Enraf Additive Monitoring System User Manual Page 17 of 24 5 6 Additive Inventory gt Sta
6. Honeywell Enraf Additive Monitoring System User Manual REVISION 0 www honeywell com ps Honeywell Enraf Additive Monitoring System User Manual Page 2 of 24 CONTENTS 1 0 Functional Overview 2 0 System Overview 2 1 System Start up Page 4 2 2 System Shutdown Page 4 2 3 Log on and User access Page 4 3 0 User Interface 3 1 Main Menu Page 5 3 2 Navigation Page 6 3 3 Operator Login Page 8 3 4 Alarm Viewer Page 9 3 5 Alarm amp Event History Page 9 4 0 Additive Injector Controllers 4 1 Overview Page Page 10 4 2 Bay Detail Page Page 11 4 3 Controller Alarm Reset Page 12 5 0 Additive Use Comparison 5 1 Overview Page Page 13 5 2 Deviation amp Pump Reset Page 14 5 3 Daily Totals Page 15 5 4 Trending Page 15 5 5 Bay Detail Page 16 5 6 Additive Inventory Page 17 6 0 Pump amp System Status 1 Pump Status Page 18 2 System Status Page 19 6 6 7 0 Additive Reports Deviation Report Page 21 7 1 7 2 Inventory Report Page 24 8 November 2008 Honeywell Enraf Additive Monitoring System User Manual Page 3 of 24 1 0 Functional Overview The system monitors fuel additive use on each loading bay for road tanker loading fuel terminals It provides control room operator access to each PCM additive injector controller installed on the loading bays monitors additive usage and provides additive inventory reports The system compares the additive volumes from the pump flow meters and additive co
7. Nov 08 E addsystem Stn01 Oper This screen shows all additive controllers in the fuel terminal Additive totals for each controller injector are displayed injector enable and alarm status is shown with green and red indicators The injector enable indicators are only used when the additive controllers are connected to accuload units The spectra tek system does not support injector enable flags Page navigation bar links Main Menu Additive Use overview Additive controller bay detail bays 1 to 4 Pump Status 8 November 2008 Honeywell Enraf Additive Monitoring System User Manual Page 11 of 24 4 2 Bay Detail Screen gt Station oper Loading Bay ControllerDetailBay4 htm Main Menu MO PI gt Additive Enraf Monitoring System Loading Bay 4 PCM Additive Controller Detail PCM 1 Shell Information PCM 2 Esso Information PCM 3 Common User Information CO IC ME J Alam ri A J enable Alm _Adotveotarvoune ME J am ff sore O ff ssa ar ass gt fx 5326 68 PCM Alarms PCM Alarms PCM Alarms Mion I Y O PC son Led 1 EH 3 EN EE ES EJES EJES 1121314 15 Main Menu Additve Use Additive Controllers Bay 1 PCM Detail Bay 2 PCM Detail Bay 3 PCM Detail Pumps Honeywell 07 Nov 08 18 10 48 addsystem Stn01 Oper This screen shows the same information as the overview screen for the selected loading bay When a controller alarm is present the injector s in alarm a
8. ected Total 26434 932 Lt 38133 074 Lt Flow Total 139 300 Lt 247 300 Lt FRRRARARENE RE Todays Totals SARA Sea Ae Injected Total 41 176 it 77 828 Lt Flow Total 44 100 Lt 94 800 Lt Deviation 6 631 17 903 8 November 2008 Honeywell Enraf Additive Monitoring System User Manual Page 23 of 24 Additive Monitoring System Deviation Report Page 3 of 3 o i o O O O __ O O _ _ __ _ _ _ o ii lt A A A A A A A A _ A A A A A A A A A A A A A A A A A run A n ee ee eee e ee ee e ee em ee ae RAW A an RAR AA 65990 039 Lt Injected Total Flow Total mta whe nta ate mha ahs ole ake ole mla ake sha nta 2 an An n anno R n so n nn na sn Injected Total Flow Total Deviation 37619 598 Lt 275 600 Lt 75 613 Lt 78 300 Lt 3 431 367 800 Lt 125 211 Lt 126 500 Lt 1 019 8 November 2008 Honeywell Enraf Additive Monitoring System User Manual Page 24 of 24 7 2 Additive Inventory Report example 07 Nov 08 18 15 12 RPTOO3 Inventory Demanded Page 1 A eS 6 142 riti SS Ss ee i triti A A A a _ ee ee ee _z lt T A 1k1n_ eee e e e Caled A le im TT TT nn n ee A a E a Vl E i e I I A I I YS NS A e e sn A A A A A A a ee A e o _ rrr r FF e
9. erfaced to a site reporting system such as IMAC via an RS232 connection A standard printer can also be used to print off the reports locally Both reports are automatically printed and or sent to the reporting system at 23 59hrs every day Before the daily values are reset to zero and 00 00hrs The reports can also be manually printed off using the Print Report buttons on the related operator station pages refer to sections 5 1 and 5 6 8 November 2008 Honeywell Enraf Additive Monitoring System User Manual Page 21 of 24 7 1 Additive Deviation Report example 07 Nov 08 18 14 38 RPTOO1 Deviation Demanded Page 1 _ se li A ml ite _ __ _ _r pgs any ey eg Se a mmm SS SS SS SS SS ee ee eee o cid __ F_F r co he _ r _ r A A A o A et Bi etere Page 1 of 3 Shell Derv Mogas ERARIRAARARER Gross Totals CELLE EE LAI Injected Total 85917 602 Lt 46658 121 Lt Flow Total 591 200 Lt 521 000 Lt Awe ea ak RRA Todays Totals ERARRARRA RARA Injected Total 256 594 Lt 133 410 Lt Flow Total 265 000 Lt 154 500 Lt Deviation 3 172 13 650 8 November 2008 Honeywell Enraf Additive Monitoring System User Manual Page 22 of 24 Additive Monitoring System Deviation Report Page 2 of 3 am e e e Me A gt as ESSO Derv Mogas ERARARARA REA Gross Totals ERARRARAREARE Inj
10. es between 30 60 seconds to carry out database checks and starts the required operating system and server services While this is done a message is displayed on the screen as follows KKKKKKKKKKKKKKKRKKKKKKKKKKKKKKKKKKKKIKKEKK Starting Operator Station Please Wait KKKKKKKKKKKKKKKRKKKKKKKKKKKEKKKKKKIKKKKKEKK The user interface then starts and the system is ready for use 2 2 System Shutdown To shut down the PC press alt ctrl del together and select shutdown The only two options available in the operator windows account are shutdown and logoff Other parts of the windows operating system including the start menu are not available in the operator windows account If the operator account is logged off for any reason it can be logged back in using the following User name oper Password password 2 3 Log on and user access There are four levels of user access on the system 1 Operator p w oper 2 Supervisor p w supv 3 Engineer p w contact Honeywell Enraf 4 Manager p w contact Honeywell Enraf The operator user access is automatically logged on at startup all other access levels auto logout back to operator level after 10mins from last keyboard mouse action Refer to section 3 3 for how to log in 8 November 2008 Enraf Additive Monitoring System User Manual Page 5 of 24 3 0 User Interface 3 1 Main Menu gt Station oper Main Menu Main htm i
11. ive Enraf Monitoring System System Status HC300 System Controller PLC Time 17 44 25 10 11 2008 Slot 1 Slot 2 Slot 3 Slot 4 Slot 5 Slot 6 Slot Slot 8 D I Module D O Module D O Module PFO Module PFO Module PFO Module Spare Spare Modbus Gateway RTU Port 0 RTU Port 1 RTU Port 2 RTU Port 3 Ond Requests 5572 5763 5921 5623 Cmd Responses 5762 5920 Gen Requests 5726 5634 5342 Gen Resporses 572 5631 5541 Errors 2 0 This page shows diagnostic information for the system The green status indicators turn red when a fault occurs in which case you should contact Honeywell Enraf for support The HC900 controller is shown at the top with CPU status indicators battery and network ports and I O status ok or fault for each I O module installed Communications diagnostic counters are displayed for the additive controller comms gateway and comms status for each additive controller on the loading bays are shown Page navigation bar links Main Menu Additive Controllers overview Additive Use overview Pump Status 8 November 2008 Honeywell Enraf Additive Monitoring System User Manual Page 20 of 24 7 0 Additive Reports Two types of additive reports are available the additive deviation report refer to section 5 1 and the additive inventory report refer to section 5 6 Both reports are configured in ASCII text format to enable them to be int
12. me rm Derv Shell ULSD 129 703 Lt Esso ULSD 6 207 Lt C U ULSD 17 812 Lt Mogas Shell PULG 62 898 Lt ESSO PULG 6 207 Lt C U PULG 13 014 Lt Shell SULG 0 000 Lt Esso SULG 0 000 Lt 8 November 2008
13. nd the alarm description is shown in the lower alarm matrix panel PCM Alarms All alarms currently available from the additive controllers are supported Alarms can be reset in the same way as using the remote control local to the additive controllers on the loading bay Page navigation bar links Main Menu Additive Controllers overview Additive Use overview Additive controller bay detail bays 1 to 4 Pump Status 8 November 2008 Honeywell Enraf Additive Monitoring System User Manual Page 12 of 24 4 3 Controller Alarm Reset Station oper Loading Bay ControllerDetailBay4 htm CO 18 x Main Menu RA PA gt ExpVistaServer B4P2ALSL SP 0 Injector Alarm Reset Select Additive Enraf Monitoring System Loading Bay 4 PCM Additive Controller Detail PCM 1 Shell Information PCM 2 Esso Information PCM 3 Common User Information DE J Enable Am M ME O 1 II E Alam fesa O fesa I CORE Efes O PCM Alarms PCM Alarms PCM Alarms bon ESE am son O PC son Led 1 EH 3 EN EE ES EJES EJES ES EJES EJES Additive Deviation No Additive Flow Leaking Solenoid Low Flow Volume No Activity Timeout Firmware Failure EEPROM Failure Reset Alarms Reset Alarms Reset Alarms Injector 1 v Injector 1 v Injector 1 v Injector 1 Injector 2 Injector 3 Injector 4 Injector 5 Main Menu Additve Use Additive Controllers Bay 1 PCM Detail Bay 2 PCM Detail Bay 3 PCM Detail
14. ntrollers on the loading bays It generates deviation alarms if there is a difference between the flow totals measured from the pump flow meters and the additive controllers on the bays If the deviation between the two measurements are significant enough indicating a leak the system disables the related additive pump The system supports loading bays controlled by both spectra tek systems and acculoads simultaneously Pump control hardwired alarms and data communications to the loading bays is all done in the control panel using a Honeywell HC900 logic controller The user interface to the system is done using an operator station PC running a stand alone version of the Honeywell Experion PKS SCADA package This is usually located in the control room which connects to the system logic controller over a dedicated network _ __uuudo uo_o_uo u__ uo u O da da_ au AA A 8 November 2008 Honeywell Enraf Additive Monitoring System User Manual Page 4 of 24 2 0 System Overview The user interface has a standard web page style layout with a main menu a top navigation bar with forward and backward buttons and each page has links to other related pages 2 1 System Start up Ensure the control panel is powered on then press the power button on the operator station PC The PC automatically logs into the operator windows account and starts the necessary processes Once the operating system has logged in it tak
15. r Manual Page 14 of 24 The gross total section shows the deviation interval comparison which is used to control the additive pumps The interval comparison is done for every 25lts of additive controller injected volume If the deviation is between 10 and 60 a deviation alarm is triggered for the related additive These parameters are default settings and can be changed with Engineer user access level contact Honeywell Enraf for more information If the deviation alarm occurs three consecutive times the pump is disabled If a deviation of 60 or more is detected a severe deviation alarm is triggered and the pump is disabled Page navigation bar links Main Menu Additive Controllers overview Additive Use Bay Detail Pump Status Additive Inventory Deviation Reset password protected pop up Daily Counter Reset password protected pop up 5 2 Deviation amp Disabled Pump Reset If a pump is disabled it can be reset by resetting the deviation The deviation can also be reset before a pump is disabled To reset a deviation login as supervisor or higher user access level The Reset Deviation link then appears on the right of the page navigation bar When the link is clicked the following pop up window appears Flow Meter Counter Reset z l hh Interval Deviation Reset Click on the relevant button to reset the deviation a confirmation dialog box appears the same as with the additive controller alarm reset
16. raf monitoring System Additive Pump Status Pump disable override key switch Pump enable status Pump disable override key switch Pump enable status Pump disable override key switch Pump enable status Pump disable override key switch Pump enable status Pump disable override key switch Pump enable Pump disable override key Pump enable status Honeywell O7 Nov 08 18 18 26 addsystem Stn01 Supv The pump status page shows the enable status for each additive pump skid The pump graphic and status message box for each pump skid is green when enabled and red when disabled A disabled pump can be reset by clicking on the pump A confirmation dialog box then appears click yes to reset the pump and related deviation The manual pump disable override key switches are also shown These are hardwired key switches located inside the system control panel These key switches override the pump disable function of the system they are usually used for maintenance purposes When a key switch is turned on this is shown on the page above a low severity alarm is triggered in the alarm viewer and an alarm window is triggered on the control room annunciator Page navigation bar links Main Menu Additive Controllers overview Additive Use overview 8 November 2008 Honeywell Enraf Additive Monitoring System User Manual Page 19 of 24 6 2 System Status Addit
17. refer to section 4 3 Click yes to reset the deviation An acknowledge dialog box then appears and the deviation and related pump if disabled is reset Click the top right x to close the pop up window 8 November 2008 Honeywell Enraf Additive Monitoring System User Manual Page 15 of 24 5 3 Daily Totals Reset The daily totals can also be manually reset Follow the same procedure as the deviation reset except click the Daily Counter Reset link on the page navigation bar This may be done during maintenance on the additive for example 5 4 Trending A trend pop up window can be viewed for each additive This shows a graph view and table history for the injected volume flow meter volume and deviation lts can be a useful tool for checking additive volumes and deviation for any time in the past To open a trend pop up click on the additive name on the additive use overview page the following trend pop up window appears Flow Trend i O _ xj M Shell Derv Additive Daily Flow Trend Additive Flow Comapare PE n es ia 1 ULALAT24 PY x i gt Period 20 Minutes y interval 1 min 08 11 2008 14 35 00 08 11 2008 14 40 00 0811 2008 14 48 00 lt D 4 gt TD SIA 1 UTATAT24 PV 2 U1A1FT24 PY 3 U1A1_DEV24 PY 08 11 2008 14 38 00 162 21 164 46 1 37 08 11 2008 14 37 00 162 21 164 46 1 37 08 11 2008 14 36 00 162 21 164 46 1 37 08 11 2008 14 35 00 158 13 160 21 1 30 0
18. t history navigate to the main menu and login using the manager access password A link then appears on the screen click on the link to view the history 8 November 2008 Honeywell Enraf Additive Monitoring System User Manual Page 10 of 24 4 0 Additive Injector Controllers 4 1 Overview Screen gt Station oper Loading Bay Overview ControllerOverview htm y F laj x Main Menu 4 PA gt Enraf Loading Bay 1 POEMA Shell Jasa Verve Tea 65 465 POM2 Esso A E AL Additive Volume 139 731 Main Menu Additve Use Additive Monitoring System Loading Bay 2 Arm Additive volume 5441 899 7588 228 12652 661 7070 605 Additive Volume 3474 546 4259 119 1088 689 3655 965 1297 812 Additive Volume 5191 875 7501 756 3869 507 1955 438 Product Codes Loading Bay 3 Additive Y olurne AL 7002 869 2104 645 0 011 16089 400 2182 792 Additive Volume 5682 460 6425 128 1593 836 5807 924 2210 902 Additive Volume 9475 167 12662 634 7020 419 3633 372 Bay 1 PCM Detail Bay 2 PCM Detail Bay 3 PCM Detail Bay 4 PCM Detail Loading Bay PCM Additive Controller Overview Loading Bay 4 PCM1 Shell _ 10161 843 14353 643 21624 463 18668 896 7563 041 Additive Volume 6932 412 8676 884 5326 695 6565 091 1536 545 Additive Volume 12197 489 18961 119 8119 896 8656 371 4224 864 Pumps Honeywell O7
19. tatus 3 Most recent alarm 4 Operator login Alarm Status amp Most recent alarm The Alarm Status box 2 flashes when alarms are present and an acknowledged in the alarm viewer it stays on when alarms are acknowledged but still present It is not visible when there are no alarms or when acknowledged alarms clear The alarm viewer is accessed by clicking on the alarm status box 2 refer to section 3 4 for details on the alarm viewer The most recent alarm 3 is displayed at the top of the bottom navigation bar in bold text The operator login box 4 shows the current user access level logged in 8 November 2008 Honeywell Enraf Additive Monitoring System User Manual Page 8 of 24 3 3 Operator Login To login click the operator login box You need to login with supervisor access level or higher to do any control actions on the system such as resetting injector controller alarms and resetting additive deviation amp disabled pumps When you click the operator login box the following box appears Station Logon x i i Please type your password de Password E Type in the password for the required user access level and press enter or click OK The default password for supervisor access level is supv To logout back to operator access level enter the default password oper For engineer and manager level passwords please contact Honeywell Enraf 8 November 2008 Honeywell
20. tion oper Additive Usage AdditiveInventory htm Main Menu RA P gt Additive re Enraf Monitoring System Additive Inventory Additive Contollers Additive Contollers Additive Contollers Injected Y olume Injected Volume Injected Yolume Shell 132 531 Shell 64 309 Shell 0 000 Esso 6 207 Esso 6 207 Esso 0 000 Common User 17 813 Common User 13 014 Print Report Additive Contollers Additive Contollers Additive Contollers Injected Y olume Injected Yolume Injected Yolume Shell 85920 430 Shell 46655 113 Shell 4 416 Esso 26434 932 Esso 18333 295 Esso 2682 525 Common User 37619 598 Common User 24738 363 Main Menu Additive Controllers Additive Use Honeywell 07 Nov 08 18 16 43 addsystem StnD1 Supy The additive inventory page shows a breakdown of each injected additive per product for inventory use As with the additive overview screen there are two sections daily totals which reset to zero at midnight and a gross totals which never reset To print off the inventory report click the Print Report button Refer to section 7 form more on additive reporis Page navigation bar links Main Menu Additive Controllers overview Additive Use overview 8 November 2008 Honeywell Enraf Additive Monitoring System User Manual Page 18 of 24 6 0 Pump amp System Status 6 1 Pump Status 3 gt Station oper Additive Usage PumpStatus htm 18 x Main Menu RA PA gt En
21. val Compare di 7 i Additive Contollers Pump Flow Meters Deviation Total Yolume Total Yolume Compare Interval Shell 3 49 Add Controller gt Flow Meter Esso 26434 932 Esso 139 300 Esso 2 05 Add Controller gt Flow Meter Common User 37619 598 Common User 275 600 Common User 5 27 Add Controller gt Flow Meter Mogas Mogas Sas oo Eo 247300 Common User 367 800 Common User 0 00 Deviation Reset Main Menu Additive Controllers Bay Additive Use Pumps Additive Inventory DeviationReset Daily Counter Reset Honeywell 07 Nov 08 18 15 24 addsystem Stn01 Supv This pages shows all additive usage in the fuel terminal It shows the sum total of all additive controller injected volumes and pump flow meter volumes for the various additives The deviation between additive controller and flow meter volumes is also displayed The page is split in two sections daily totals which automatically reset to zero at midnight every day and gross totals which never reset Additives in use are highlighted in green this indicates that the pump enable output from the system control panel is on for the related additive providing the pump control system is healthy the pump should be running To print off the daily total additive report click the Print Report button on the page Refer to section 7 for more on additive reports 8 November 2008 Honeywell Enraf Additive Monitoring System Use
Download Pdf Manuals
Related Search