Installation Manual
Contents
1. Prior to attaching your monitor install the monitor cables Run them through the Front Cable Access Port down the pole and out of the Cable _ Access Hole in the work Step 8 Install Monitor Cables Step 9 Attach the VESA Plate to your Display _Mounting Screws x4 VESA Plate Hook the top of the VESA plate onto he Quickshift Mount Back of Display a Press and hold the Release Buttons Gently push bottom of VESA Plate into Quickshift Mount Release Buttons to lock in place Release Button optional Insert the Security Screw and tighten using a Phillips head Screwdriver Phillips head Screwdriver _ AA TIGHTEN Securiiy crew Back of Bienlay Step 11 Adjust the VESA Ball Mount Position your Display to the desired viewing angle using angular movement allowed by the VESA Ball Mount If the display does not hold its position or is too resistant adjust the Tension Plate located at the rear of the VESA Ball Mount To make any adjustments use the 3mm Allen Key supplied Apply half a turn at a time to each screw on the Tension Plate to adjust evenly Check the display and the adjust again if necessary Installation Complete the 40 henrik kg LOOSEN kg 7 3mm Allen Key a rn atdec Advanced Security Installation These Installation Instr2. 55 Rotation 0 355 M USER Direction Arrow a MN USER Step 1 Check Components Check you have received all parts against the component checklist and Hardware above Step 2 Limit Rotation A Determine the degree of rotation E LOCKING HOLES you require Jo N Direction Arrow refer to Mounting Options above Ae omm Alenke y 0 Locking Hole Fixed B To limit the rotation use the 2 5mm Allen Key to insert the K 0 90 Locking Hole supplied M5 Grub Screw into your chosen Locking Hole until it sits flush with the Base Plate NOTE If you want the full 355 rotation you do NOT need to install a grub screw M5 Grub Screw Base Plate j 0 180 Locking Hole lt 0 270 Locking Hole Step 3 Locate and Secure your POS Height Adjustable A Position the Installation Template in the desired location on your work surface Ensure the straight q eee 4x D3mm 0 12 S N edge sits perpendicular with the User s line of ND Sera Pilot Holes sight Mark the center points of each of the gt T i required holes onto the work surface with a pencil Cable Access Hole B Drill 4 x 3mm 0 12 Pilot Holes to a depth of la INSTALLATION al ny TEMPLATE ee m 15mm 0 59 Use a 45mm 1 75 hole saw to drill the Cable Access Hole in the work surface Reposition SD POS HA with the Direction Arrow pointing in the direction required for your chosen rotatio
3. SD POS HA Installation Instructions dec Display POS Height Adjustable Component Checklist j Hardware C M4x10mm x4 Top Cap x1 N le Installation i 3 2 5 A 14G 5mm VESA Plate x1 Template x1 Screws KA Allen Key x1 each go M4x16mm x4 lt a gt e lt 3 Screw Cover x1 3 D A bc Display Mounting POS Assembly x1 NOTE Philips head SIO Perera Screws screwdriver not supplied IMPORTANT INFORMATION IMPORTANT Install Spacedec POS Height Adjustable as per Installation Instructions This product supports a maximum load of 20kg 44 bs l This product supports VESA mounting hole configurations 75x75mm and 100x1 00mm The height adjustment range from desk level to the centre of the screen 330 450mm 12 99 17 72 The minimum thickness of the mounting surface is 15mm 0 59 when using the manufacturer supplied Hardware The manufacturer accepts no responsibility for incorrect installation Mounting Options Your SD POS HA offers 355 of Rotation This can also be limited to suit a specific Direction _ 5 eo application The direction in A OUr ae inshorations pi S SD POS HA Rotation Options vw NS sient which you mount 0 Rotation Fixed 180 90 Rotation will determine where the 5 0 90 Rotation LY gap in rotation is located 0 180 Rotation 7 and how you choose to limit 0 270 Rotation age Ae the past 0 3
4. n Secure the SD POS HA to the work surface using the supplied 14 Gauge Screws x4 4x 3mm 0 12 Pilot Holes 45mm A 1 75 Cable j Access Hole Step 4 Attach Screw Cover Remove the paper backing from the Screw Cover and adhere to the base as shown f Screw Cover Top Cap PUSH Push down firmly to attach the Top Cap Step 8 Install Monitor Cables Option 2 When you do not want to route the cables below the work surface CABLE _ACCESS CAP OUT A Push out to remove Cable Access Cap B Pull cables out through Rear Cable Access Port Step 5 Optional Install Monitor Security Cable A Loop the Security Cable Kensington or similar around the internal post of the POS Assembly B Feed the other end of the cable through the POS Assembly and out the Cable Management Hole C After you have attached the monitor As directed in Step 9 install the lock to the monitor as per the manufacturer guidelines Note Security Cable Not Included Step 7 Adjust Pole Height A Loosen Hand S Grip ant B Set to desired Height psal o C Tighten Hand Grip to lock pole at desired Heo surface There are two mounting hole configurations e 75x 75mm 100 x 100mm Choose appropriate J Mounting Screws from gt the Hardware supplied to suit your Display Step 10 Attach your Display to the POS Assembly Option 1
5. uctions secure the SD POS HA using the provided fasteners from the above work surface For advanced Security Installation trom below the work surface Please refer to the Advanced Security Installation Addendum No portion of this document or any artwork contained herein should be reproduced in anyway without the express written consent Atdec Pty Ltd Due to continuing product development the manufacturer reserves the right to alter specifications without notice Published 08 02 12
Download Pdf Manuals
Related Search