dekker_led
Contents
1. Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice American DJ www americandj com Dekker LED Instruction Manual Page 15 Auto Sensing Voltage This fixture contains a automatic voltage switch which will auto sense the voltage when it is plugged into the power source American DJ Supply American DJ World Headquarters 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 2650 Fax 323 725 6100 Web www americandj com E mail info americandj com2. DMX of the last fixture 1 2 3 1 2 3 DMX DMX COMMON DMX512 OUT 3 PIN XLR Figure 2 Figure 3 1 Ground 1 Ground XLR Male Socket XLR Pin Configuration 3 Hot 2 Cold 2 Cold 3 Hot XLR Female Socket Pin 3 Data True positive Pin 2 Data Compliment negative Pin 1 Ground Special Note Line Termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior A terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male XLR connector DATA and DATA This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line Using a cable terminator ADJ part number Z DMX T will decrease the possibilities of erratic behavior DMX512 IN 3 PIN XLR SOUND REMOTE CONTROL INPUT POWER INPUT OUTPUT SOUND REMOTE CONTROL INPUT POWER INPUT OUTPUT SOUND REMOTE CONTROL INPUT POWER INPUT OUTPUT DMX512 DMX DMX COMMON 1 2 3 Termination reduces signal errors and avoids signal transmission problems and interference It is always advisable to connect a DMX terminal Resistance 120 Ohm 1 4 W between PIN 2 DMX and PIN 3 DMX of the last fixture 1 2 3 1 2 3 DMX DMX COMMON DMX512 OUT 3 PIN XLR Figure 4 5 Pin XLR DMX Connectors Some manufactures use 5 pin DMX 512 data cables for DATA
3. sounds may not activate the unit Dekker LED Trouble Shooting Dekker LED Cleaning Fixture Cleaning Due to fog residue smoke and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light output 1 Use normal glass cleaner and a soft cloth to wipe down the outside casing 2 Use a brush to wipe down the fan grill 3 Clean the external optics with glass cleaner and a soft cloth every 20 days 4 Clean the internal optics with glass cleaner and a soft cloth every 30 60 days 5 Always be sure to dry all parts completely before plugging the unit back in Cleaning frequency depends on the environment in which the fixture operates I e smoke fog residue dust dew In heavy club use we recommend cleaning on a monthly basis Periodic cleaning will en sure longevity and crisp output Dekker LED Fuse Replacement Fuse Replacement First unplug the power The fuse holder is lo cated at the rear of the unit next to the power cord Using a flat head screw driver unscrew the fuse holder Remove the bad fuse and re place with a new one American DJ www americandj com Dekker LED Instruction Manual Page 12 American DJ www americandj com Dekker LED Instruction Manual Page 11 Dekker LED 8 Channel Mode DMX Values amp Traits Channel Value Function 1 MOTOR FUNCTION CONTROL 1 127 ROTATE CLOCKWISE SLOW FAST 128 255 ROTATE COUNTER CLOCKWISE FAST SLOW 2 RED INTENS
4. transmission in place of 3 pin 5 pin DMX fixtures may be implemented in a 3 pin DMX line When inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores The chart below details a proper cable conversion Conductor 5 Pin XLR Male In 3 Pin XLR Female Out Pin 1 Do Not Use Do Not Use Pin 3 Pin 2 Pin 1 Pin 3 Pin 2 Not Used Not Used Data True signal Data Compliment signal Ground Shield 3 Pin XLR to 5 Pin XLR Conversion American DJ www americandj com Dekker LED Instruction Manual Page 7 American DJ www americandj com Dekker LED Instruction Manual Page 8 LED Display On Off To set the LED display to turn off after 10 seconds press the MODE button until 0001 is displayed press the UP button to display 0002 Now the display will disappear after 10s Press any button for at least 10s to turn the display on again Be advised though that the display will turn off automatically after 10 seconds To set the display press the MODE button until 0001 is displayed The display will now stay on at all times ds 1 LCD display on at all times ds 2 LCD display shuts off after 10 seconds Master Slave Operation This function will allows you to link units together to run in a Master Slave mode In Master Slave operation one unit will act as the con trolling unit and the others will react to the cont
5. written descriptions of warranty terms and conditions heretofore published MANUFACTURER S LIMITED WARRANTY PERIODS All American Audio Products 1 year 365 day Limited Warranty except V Plus Series Ampli fiers All American Audio V Plus Series Amplifiers 3 year 1095 day Limited Warranty American DJ Lighting and American DJ Branded Products 1 year 365 day Limited Warranty Such as Special Effect Lighting Intelligent Lighting UV lighting Strobes Fog Machines Bubble Machines Mirror Balls Par Cans Trussing Lighting Stands etc excluding Laser Products and lamps American DJ Laser Products 90 Day Limited Warranty American DJ L E D Products 3 year 1095 day Limited Warranty excluding motors which have a 1 year 365 day Limited Warranty American DJ www americandj com Dekker LED Instruction Manual Page 14 American DJ www americandj com Dekker LED Instruction Manual Page 13 Dekker LED Notes American DJ Europe Junostraat 2 6468 EW Kerkrade Netherlands service adjgroup eu www americandj eu Tel 31 45 546 85 00 Fax 31 45 546 85 99 Technical Specifications Model Dekker LED LEDs 2 x 5W RGBW LEDs Voltage 100 240v 50Hz 60Hz Power Consumption 25W Dimensions 11 L x 9 8 W x 10 23 H Colors RGB White Weight 8 5 Lbs 3 85 Kgs DMX Channels 2 Channel or 8 Channels Fuse 1 Amp Duty Cycle None Dekker LED Specifications
6. ITY 1 255 0 100 3 GREEN INTENSITY 1 255 0 100 4 BLUE INTENSITY 1 255 0 100 5 WHITE INTENSITY 1 255 0 100 6 MASTER INTENSITY CONTROL 0 100 7 PROGRAMS 1 26 4 COLOR LOOP CHANGE 27 51 9 COLOR FADE CHANGE 52 76 4 COLOR LOOP CHANGE 77 101 9 COLOR LOOP CHANGE 102 126 STROBE 1 DIM BRIGHT 127 151 STROBE 2 BRIGHT DIM 152 176 STROBE 3 DIM BRIGHT DIM 177 201 STROBE 4 W O DIM EFFECT 202 226 STROBE 5 WITH 9 COLOR 227 254 STROBE 6 WITH GRADUAL DIM 255 ALL PROGRAMS WILL CYCLE 8 PROGRAM SPEED 1 254 SLOW FAST 255 SOUND ACTIVE NOTE Regarding Channel 7 LED intensity is controlled by Channels 2 5 Channel 7 LED program speed is controlled by Channel 8 Dekker LED Warranty MANUFACTURER S LIMITED WARRANTY A American DJ Inc hereby warrants to the original purchaser American DJ and American Audio products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase see specific warranty period on reverse This warranty shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by ac ceptable evidence at the time service is sought B For warranty service you must obtain a Return Authorization number RA before sending back the product Contact American DJ Inc Service Department
7. User Instructions Dekker LED Introduction American DJ www americandj com Dekker LED Instruction Manual Page 2 Rev 5 12 Unpacking Thank you for purchasing the Dekker LED by Ameri can DJ Every Dekker LED has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your fixture for any damage and be sure all accessories necessary to operate the unit has arrived intact In the case damage has been found or parts are miss ing please contact our toll free customer support number for further instructions Do not return this unit to your dealer without first contact ing customer support Introduction The Dekker LED is part of American DJ s continu ing pursuit for creating high quality affordable intelligent fixtures The Dekker LED is a DMX intelligent LED mooflower effect This fixture can be used in a stand alone mode or connected in a Master Slave configuration The unit can also be controlled via DMX controller This wash has four operating modes Sound Active mode Auto mode Static mode and DMX control mode Customer Support American DJ provides a toll free customer support line to provide set up help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www americandj com for any co
8. at 800 322 6337 Send the product only to the American DJ Inc factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty American DJ Inc will pay return shipping charges only to a designated point within the United States If the entire instrument is sent it must be shipped in it s original package No accessories should be shipped with the product If any accessories are shipped with the product American DJ Inc shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof C This warranty is void if the serial number has been altered or removed if the product is modified in any manner which American DJ Inc concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the American DJ Inc factory unless prior written authorization was issued to purchaser by American DJ Inc if the product is damaged because not properly maintained as set forth in the instruction manual D This is not a service contract and this warranty does not include maintenance cleaning or periodic check up During the period specified above American DJ Inc will replace defec tive parts at its expense with new or refurbished parts and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmans
9. ck Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if it becomes damaged This unit is intended for indoor use only use of this product out doors voids all warranties During long periods of non use disconnect the unit s main power Always mount this unit in safe and stable matter Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to the point they exit from the unit Cleaning The fixture should be cleaned only as recommended by t he manufacturer See page 12 for cleaning details Heat The appliance should be situated away from heat sources such as radiators heat registers stoves or other appliances inclu d ing amplifiers that produce heat The fixture should be serviced by qualified service personnel when A The power supply cord or the plug has been damaged B Objects have fallen or liquid has been spilled into the appliance C The appliance has been exposed to rain or water D The appliance does not appear to operate normally or exhibits a marked change in performance American DJ www americandj com Dekker LED Instruction Manual Page 6 American DJ www americandj com Dekker LED Instruction Manual Page 5 Power Supply The American DJ Dekker LED co
10. cting customer support at 800 322 6337 Dekker LED Features Q4 LED Technology Includes Built In Hanging Yoke Sound Active Light Weight Strobing Electronic Dimming 0 100 Built in Microphone DMX 512 protocol 2 DMX Channel Modes 2 Channels amp 8 Channels To optimize the performance of this product please read these operating instructions carefully to familiarize yourself with the basic operations of this unit These instructions contain important safety information regarding the use and maintenance of this unit Please keep this manual with the unit for future reference Dekker LED General Instructions Dekker LED Safety Precautions To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Do not spill water or other liquids into or on to your unit Be sure that the local power outlet match that of the required volt age for your unit Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside Never operate this unit when it s cover is removed Never plug this unit in to a dimmer pa
11. er LED can be a 2 channel DMX unit or 8 channel DMX unit The DMX address is set electronically using the controls on the rear panel of the unit Your unit and your DMX controller require a approved DMX 512 110 Ohm Data cable for data input and data output We rec ommend Accu Cable DMX cables If you are making your own cables be sure to use standard 110 120 Ohm shielded cable This cable may be purchased at almost all professional sound and lighting stores Your cables should be made with a male and female XLR connector on either end of the cable Also remember that DMX cable must be daisy chained and cannot be split Dekker LED Set Up Figure 1 Notice Be sure to follow figures two and three when making your own cables Do not use the ground lug on the XLR connector Do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior Dekker LED Set Up DMX512 IN 3 PIN XLR SOUND REMOTE CONTROL INPUT POWER INPUT OUTPUT SOUND REMOTE CONTROL INPUT POWER INPUT OUTPUT SOUND REMOTE CONTROL INPUT POWER INPUT OUTPUT DMX512 DMX DMX COMMON 1 2 3 Termination reduces signal errors and avoids signal transmission problems and interference It is always advisable to connect a DMX terminal Resistance 120 Ohm 1 4 W between PIN 2 DMX and PIN 3
12. hip The sole responsibility of American DJ Inc under this warranty shall be limited to the repair of the product or replace ment thereof including parts at the sole discretion of American DJ All products covered by this warranty were manufactured after January 1 1990 and bear identifying marks to that effect E American DJ Inc reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore manufactured No warranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by American DJ Inc in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall American DJ Inc be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product This warranty is the only written warranty applicable to American DJ and American Audio Products and supersedes all prior warranties and
13. mments or suggestions Service Hours are Monday through Friday 8 00 a m to 4 30 p m Pacific Standard Time Voice 800 322 6337 Fax 323 582 2941 E mail support americandj com To purchase parts online visit http parts americandj com Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures war ranty In the unlikely event your unit may require service please contact American DJ PLEASE recycle the shipping carton when ever possible American DJ www americandj com Dekker LED Instruction Manual Page 3 American DJ www americandj com Dekker LED Instruction Manual Page 4 Dekker LED Warranty Registration The Dekker LED carries a three year 1095 days limited warranty Please fill out the enclosed warranty card to validate your purchase All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A num ber The R A number must be clearly written on the outside of the return package A brief description of the problem as well as the R A number must also be written down on a piece of paper and included in the shipping container If the unit is under warranty you must pro vide a copy of your proof of purchase invoice You may obtain a R A number by conta
14. ntains a automatic voltage switch which will auto sense the voltage when it is plugged into the power source With this switch there is no need to worry about the correct power voltage this unit can be plugged in anywhere DMX 512 DMX is short for Digital Multiplex This is a universal pro tocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions from the controller to the fixture DMX data is sent as serial data that trav els from fixture to fixture via the DATA IN and DATA OUT XLR ter minals located on all DMX fixtures most controllers only have a DATA OUT terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a sin gle controller as long as all fixtures and the controller are DMX com pliant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX Operation The Dekk
15. rolling units built in programs Any unit can act as a Master or as a Slave however only one unit can be programmed to act as the Master Master Slave Connections and Settings 1 Daisy chain your units via the XLR connector on the rear of the unit Use standard XLR microphone cables to link your units together Remember that the Male XLR connector is the input and the Female XLR connector is the output The first unit in the chain master will use the female XLR connector only The last unit in the chain will use the male XLR connector only 2 You will also have to link the power cords to each other as you did with the XLR cables 3 Choose your Master unit and press the MODE button until 5 XX is displayed You are now in Master mode and you can use the UP or DOWN buttons to select your desired show from 0 20 or Sound Active 5 So 4 With the Slave unit s press the MODE button until 4 XX is displayed They will now follow the Master unit Dance Mode There are two dance programs to choose from fast dance and slow dance 1 Plug the fixture in and press the MODE button until 1 X is Dekker LED Operating Instructions displayed X represents the current number being displayed 2 Select your desired dance program by pressing either the UP or DOWN buttons 3 1 1 is a fast dance program 1 2 is a slow dance program DMX Mode The Dekker LED has 2 DMX Channel modes You can choose be
16. ructions American DJ www americandj com Dekker LED Instruction Manual Page 10 American DJ www americandj com Dekker LED Instruction Manual Page 9 2 Now you can use the UC3 Controller Not Included to control vari ous functions See below for UC3 controls Dekker LED Operating Instructions Button Function STAND BY Open or close screen when pressing this button 1 R 2 G 3 B 4 W 5 RGBW 6 Auto Mix color FUNCTION 7 Sound Mode STR OBE Open or close strobe mode when pressing this button Dekker LED 2 Channel Mode DMX Values amp Traits Channel Value Function 1 PROGRAMS 1 26 4 COLOR FADE CHANGE 27 51 9 COLOR FADE CHANGE 52 76 4 COLOR LOOP CHANGE 77 101 9 COLOR LOOP CHANGE 102 126 STROBE 1 DIM BRIGHT 127 151 STROBE 2 BRIGHT DIM 152 176 STROBE 3 DIM BRIGHT DIM 177 201 STROBE 4 W O DIM EFFECT 202 226 STROBE 5 WITH 9 COLOR 227 254 STROBE 6 WITH GRADUAL DIM 255 ALL PROGRAMS WILL CYCLE 2 PROGRAM SPEED 1 254 SLOW FAST 255 SOUND ACTIVE Trouble Shooting Listed below are a few common problems that you may encounter with solutions No light output from the unit 1 Be sure you have connected your unit into a standard 110V wall outlet 2 Be sure the fuse has not blown The fuse is located on the rear panel Unit does not respond to sound 1 Low frequencies bass should cause the unit to react to sound Tapping on the microphone quiet or high pitched
17. tween 2 DMX channels or 8 DMX Channels Operating through a DMX controller give the user the freedom to create their own pro grams tailored to their own individual needs 1 This function will allow you to control each individual fixture s traits with a standard DMX 512 controller such as the Elation Show Designer or the Elation DMX Operator 2 To run your fixture in DMX mode plug in the fixture via the XLR connections to any standard DMX controller 3 Choose your DMX channel mode Press the MODE button until 2XXX is displayed this is 2 chan nel mode Press the UP or DOWN button to find your desired DMX address Press the MODE button until 3XXX is displayed this is 8 chan nel mode Press the UP or DOWN button to find your desired DMX address 4 Please see pages 10 11 for DMX values and traits Adjustment Mode 1 Plug the fixture in and press the MODE button until 6 XX is displayed 2 Select your desired program in mode 6 by pressing either the UP or DOWN buttons There are 10 programs to choose from 3 Adjust the program speed by pressing the MODE button until 7 XX is displayed Press either the UP or DOWN buttons to ad just the speed of the program When 7 so is displayed the pro gram is running in sound active mode UC3 F Mode Choose a color to remain static 1 Plug the fixture in and press the MODE button until UC3 F is displayed Dekker LED Operating Inst
Download Pdf Manuals
Related Search
dekker_led dekker led verlichtingsset adj dekker led