user manual
Contents
1. 80 mm thick and are round Use Important test the trimmer with a small amount of plant material first to ensure your satisfaction step 7 Start the upper motor by putting the button to RUN to engage the rubber or neoprene tumbler paddles Turn the rheostat to the desired speed between 0 and 60 rpms Now start the lower motor on VAR and adjust the cutting speed with the rheostat You can also use your ThunderVak as a table top trimmer by simply removing the upper reservoir and disconnecting the upper motor electrical cord Preparation We recommend removing the stems before placing the plant material in the machine You do not have to remove the larger leaves for this machine as the trimming is more precise and efficient than other models on the market 2012 All rights reserved ThunderVak Registered Trademark of 105766 Canada Inc www ThunderVak com page 9 Transportation Always turn the motors off and unplug the machine before moving it When transporting it always secure it to prevent damages Adjusting the trimming height Note the height has already been factory preset and should not require any adjustment Block to adjust the trimming height This tool is used to adjust the cutting height 4 union nuts on the lower base motor support allow adjustment of the trimming height and are pre set by the manufacturer Turning left will distance the wires from the plant material and turnin2. COMPOSTER USER MANUAL Version 1 0 09 2012 2012 All rights reserved ThunderVak Registered Trademark of 105766 Canada Inc 2012 All rights reserved ThunderVak Registered Trademark of 105766 Canada Inc SO O Table of contents FIG AE teeee E E E E Page 5 6 a e A A E E E N Page 5 Partea A e ctce areasuenaa aban nea seateeaaesaseaeeasaei ia aeacenaenieeeeen esas Page 6 DS Dy WAND e E E Page 7 Electrical treguirenie iS esisiini Page 7 Ja cho e a E N E E N Page 8 9 NS E E E E A E E eet E Page 9 10 Prepara NOT rrna a an E E S Page 9 Trane POr O sis A Page 10 Adjusting thetrimming height isessccsscscsescescdsaeenreeteaednmernteerenneriadans Page 10 E OUE E E E E fer nee E E eee re Page 10 AA s 6200 AP peer sree eee eee E E eee ee ee ee Page 11 US and Canadian patents pending Page 4 www ThunderVak com lls Parts Parts List 12 oL NDMP WN v vvvy white lower reservoir with 2 handles lower base motor support with aluminum crosspiece removable side chute drop door capacitor and rheostat for the cutting motor base motor transparent top reservoir with feeder upper motor with speed control head motor white metal crosspiece with 4 tumbler paddles 2 sets of 4 paddles one in rubber rigid and one in neoprene flexible aluminium grill cutting wires 8 blue 80 mm nylon cutting wires 8 red ones 65 mm a tool set consisting of one 1 8 Allen key one 3 8 Allen key hex nut
3. d workmanship for a period of ONE 1 YEAR from the date of original retail purchase excluding all replacement rubber parts and cutting wires If a defect exists at its option ThunderVak will 1 repair the product at no charge using new or refurbished replacement parts or 2 exchange the product with a product that is new or which has been manufactured from new or serviceable used parts and is at least functionally equivalent to the original product If usage of this ThunderVak product violates the guidelines of this limited warranty ThunderVak will repair the product and charge the purchaser for the cost of company time materials and shipping costs Thunder Vak shall not be liable for any loss injury or damages to persons or property resulting from the use of this product or any failure of or defect in this product nor shall ThunderVak be liable to the initial user of this product or to any other person or entity for any general special direct indirect incidental consequential exemplary punitive or OTHER DAMAGES of any kind or nature whatsoever 2012 All rights reserved ThunderVak Registered Trademark of 105766 Canada Inc www ThunderVak com page 11 Mega Watt HydroCulture Distributed by 105766 Canada Inc MegaWatt HydroCulture 636 Route 364 Morin Heights PQ JOR 1H0 Canada 1 800 575 2515 www MegaWattHydro com US and Canadian patents pending 2012 All rights reserved ThunderVak Regis
4. driver block to adjust trimming height 1 white lower reservoir with 2 lower base motor support 3 removable side chute 2 handles with aluminum crosspiece 2012 All rights reserved ThunderVak Registered Trademark of 105766 Canada Inc www ThunderVak com page 5 Parts diagrams 4 drop door 7 upper motor 8 crosspiece with paddles 9 tumbler paddles 11 blue cutting wires 11 red cutting wires 12 tool set 12 block to adjust trim height US and Canadian patents pending Page 6 www ThunderVak com Safety warnings This is a high speed power tool and should be taken seriously Careless or improper use may cause serious or even fatal injury Warning IMPORTANT e Make sure to inspect the machine before each use e Always wear safety glasses gloves ear plugs and proper protective clothing e Do not apply pressure to the grill e Do not use any instruments or tools above the machine e Keep work area clean and clear of debris e Always disconnect the power before servicing the machine e Never move tilt or rotate machine while in use e Never allow the machine to run unattended e Minors should never be allowed to operate this machine This machine is to be used with all existing laws and regulations The manufacturer and distributor does not accept any liability or responsibility for misuse of the product or for damages caused to or by the ThunderVak resulting from impr
5. e motor support Turn slightly to the left to lock it into place Adjustments to the height of the paddles can be made using the 1 8 Allen key we suggest letting them rest lightly on the grill 5 Slide the drop door into the grooves alongside the opening on the top reservoir Secure the removable side chute into place by using the rivets on either side of the opening 6 Put the capacitor and rheostat base motor onto the side of the lower base motor support using the metal slide 7 Plug the power cords together gt Plug the green stickered cords together this is for the capacitor and rheostat for the cutting motor gt Plug the red stickered cords together this is for the upper motor with speed control gt Plug the black electrical cord into a 120 Volt wall receptacle step 4 US and Canadian patents pending Page 8 www ThunderVak com Oo Assembly cont d Notes gt The ThunderVak comes with the neoprene tumbler paddles installed A set of rubber ones have been included for your convenience If you would like to change them simply unscrew the paddles with a Phillips screwdriver gt The ThunderVak red cutting wires are already installed but if you would like to change them simply slide them out and replace inserting each blue wire into the spool the metal grommet will hold the wires in place The red cutting wires are 65 mm thick and are octogonal shaped The blue cutting wires are
6. g the union nuts to the right will bring the wires closer to the plant material to be trimmed Place the grill onto the lower base motor support ensuring that it is level and start the rheostat on high Use the tool to adjust the desired height we suggest 5 32 in By placing the block on the grill and adjusting one nut at a time to the desired height union nut Maintenance To receive maximum performance from the Thunder Vak it is important that the maintenance schedule be followed Always stop the motor and unplug the unit before any maintenance repairs or cleaning Cleaning the machine after each use will ensure the ThunderVak longevity To clean it we suggest using Bio Green Clean or other natural cleaner Simply follow the instructions on the bottle for the dilution rate spray down the machine let it sit for a few minutes and wipe clean with a damp cloth Never use an abrasive pad on any component of this machine as it will scratch the surface Make sure that all 8 cutting wires are in good condition before operating the machine Each machine comes with replacement cutting wires If one needs replacement simply slide it out discard and replace with a new one US and Canadian patents pending Page 10 www ThunderVak com lll tC Warranty ThunderVak warranty obligations are limited to the terms set forth below ThunderVak 105766 Canada Inc warrants this hardware product against defects in materials an
7. oper use or assembly Read the entire user s manual prior to operating the ThunderVak Read all warnings before operating Electrical Requirements Wiring requirements 110V I5amps The ThunderVak is equipped with a power supply cord having a grounded 3 prong plug To minimize possible Electrical shock hazard the cord must be plugged into a mating grounded 3 prong outlet grounded in accordance with all Shock local codes and ordinances Hazard 2012 All rights reserved ThunderVak Registered Trademark of 105766 Canada Inc www ThunderVak com page 7 MO Assembly To receive maximum performance and satisfaction from the Thunder Vak it is important that you read and understand the safety warnings before using this machine 1 Take everything out of the lower reservoir 2 Place the lower base motor support into the white reservoir ensuring that the chute opening aligns with the cutouts in the lower reservoir and that the aluminum grill sits level 3 Place the upper motor with speed control into the cavity on top of the reservoir Hand tighten the motor into place with the nuts provided Once the motor in secured into place tighten the bolts with the hex nut driver 4 Next place the white crosspiece with tumbler paddles on the motor cam shaft ensuring that the bolt aligns with the slot on the camshaft Tighten carefully with the 1 8 Allen key and place the reservoir back into the 5 slots on the lower bas
8. tered Trademark of 105766 Canada Inc
Download Pdf Manuals
Related Search