30052 Door Announcer Set v01.p65
Contents
1. The Door Announcer will send a signal to the Smart Home Receiver that the Door Announcer has been moved 3 The position farthest from the edge is the Alarm Mode In this mode the Door Announcer will sound an alarm sound for 45 seconds then automatically reset The Door Announcer will send an alarm signal to the Smart Home Receiver that the Door Announcer has been moved The Smart Home Receiver will sound for 25 minutes or until reset TESTING THE SYSTEM PRIOR TO INSTALLATION 1 Select the operational mode of the Door Announcer chime or alarm 2 Set the Door Announcer on a solid surface and let it rest for 30 seconds without touching it 3 Rotate or move the Door Announcer 4 The Door Announcer will chime or alarm to notify you that it has been moved Door Announcer 30052 Page 2 MOUNTING THE Door Announcer SENSOR Attach the Door Announcer to the object to be moni tored using the double stick foam tape or the Phillips screws provided The flat end of the case should lie tight against the monitored object HOW THE DOOR ANNOUNCER WORKS The Door Announcer uses a patented magnetometer sensor system Moving the monitored object causes the magnet field around the Door Announcer to change causing the Door Announcer to sound an alert Once the motion has stopped the Door Announcer automatically resets and is ready for the next event SENSITIVITY SETTINGS The Door Announcer is factory set to the medium2. nsor Learning section on the next page Door Announcer 30052 Page 4 4 SENSOR LEARNING do only if receiver does not respond 1 With the receiver plugged in and the red POWER light on move the slide switch closest yb to the antenna to the TRANS LEARN position toward the an tenna wire The green light will glow steadily while in this sen sor learning position EN TRANS NORM USE ee 2 Push the Reset Button on the top of the case down for 1 ae This will erase any previous learned codes 3 Rotate the Door Announcer sensor The receiver will chirp to indi cate that it has learned the code from the Door Announcer sensor 3 Slide the code learning switch back to the NORM USE gt position away from the an tenna wire for normal opera A tion Do NOT press the RE SET button before sliding the switch back to the NORM USE position or the code will be antennavack TRANS NORM erased The green light will Dh GAES eae turn off To Lower Volume 5 ADJUSTING THE VOLUME The receiver comes factory set to the louder volume setting To lower the volume set the volume switch to the setting toward the edge of the case For louder volume ree eee NORM F Lume set the switch back to the setting toward the antenna Page 5 Door Announcer 30052 OPTIONAL ACCESSORIES The Long Range Antenna increases the range of the Door Announcer system up to double the regular
3. range For louder sound the Plug In Siren makes a loud sound that can be heard from anywhere in your home when the mail arrives DesignTech also makes a line of other sensors which can be used with your Mail Alert system Driveway Monitor alerts you anytime a vehicle arrives at or departs from your driveway Mail Alert wirelessly detects the opening of your mail box door when the mail man arrives You can use more than one of these sensors with one Door Announcer receiver Each type of sensor will produce a different chime from the re ceiver when triggered You can also have several Door Announcer sen sors and several receivers work together as a system useful for large homes ITEM Part Price Long Range Antenna 30316 49 95 Additional Door Announcer Sensors 30062 44 95 Mail Alert Sensor 30065 44 95 Driveway Monitor Sensor 30075 129 95 Motion Alert Sensor 30067 49 95 Plug In Siren 30319 19 95 Additional Door Announcer Receiver 30317 59 95 All prices are in US dollars and include shipping and handling Contact your local distributor or call DesignTech to order This device complies with FCC Rules Part 15 Operation is subject to two conditions 1 This device may not cause harmful interference and 2 it must accept any interference received including that which may cause undesirable operation FCC ID ELGMOTION amp ELGHOME DOC 1476 102 203 and 1476 102 203 A User is cautioned that changes or modifica
4. s and reset the unit 3 If there is no response from the Door Announcer a First check the batteries and replace if necessary Replace with 2 CR2025 b Check the position of the three position slide switch the unit may accidentally switched to the Silent Operation Mode c Ifthe batteries are fresh try setting the Door Announcer to another sensitiv ity setting see the Sensitivity Setting Section The Door Announcer maybe having difficulty detecting changes in the surrounding magnetic field SETTING UP THE SMART HOME RECEIVER 1 Plug the AC adapter into any standard electrical wall outlet and the other end into the back of the re ceiver The red POWER light will come on and the receiver will chirp 2 Door Announcer comes with a 9 inch antenna e which plugs into the antenna jack on the back of the receiver The antenna should be vertical TESTING THE SYSTEM PRIOR TO INSTALLATION 1 The sensor and receiver are factory set to a unique code Prior to installation set the switch on the Door Announcer to CHIME and test the system by rotating the sensor while you are more than 5 feet away from the receiver The receiver will chime and the green light will flash If the receiver does not chime or the green light does not come on first check that the red POWER light on the receiver is on and that the batter ies are inserted correctly in the Door Announcer sensor If the receiver still does not respond see the Se
5. setting the small jumper inside the case is only connected to the center pin If the Door Announcer does not respond to the motion of the monitored object the sensitivity may have to be changed Moving the jumper to connect the low est pin marked with an L and the center pin the sensitivity is in the lowest setting It will take a large movement Low Sensitivity of the Door Announcer to sound an alert Moving the jumper to connect the highest pin marked with an H and the center pin the sensitivity is in the highest setting A very small movement of the Door Announcer will sound an alert You may need to experiment with your application to find the best sensitivity setting that works for you Page 3 Door Announcer 30052 Troubleshooting 1 False alerts when Door Announcer is not moved Movements of large metal objects such as other large metal doors being opened or closed near the Door Announcer may cause a false signal Since the Door Announcer senses changes in the surrounding magnetic field large magnets found in some speakers television and computer monitors may also cause false signals Try moving the Door Announcer to a slightly different location 2 If the Door Announcer constantly alerts Check the batteries When the batteries are weak and need to be replaced the Door Announcer will start chaining or alert several times for just one event Replace with 2 CR2025 batteries with fresh one
6. tions not expressly approved by DesignTech could void the user s authority to operate this equipment Covered under US Patent s 4 851 775 amp 5 239 264 Lesigniech INTERNATIONAL INC 7955 Cameron Brown Court Springfield Virginia 22153 USA Tel 703 866 2000 or 800 337 4468 Fax 703 866 2001 www designtech intl com 2000 DesignTech International Inc Door Announcer 30052 Page 6
7. v0 01 User s Manual TM Door Announcer System Model 30052 Congratulations on the purchase of the DesignTech s Door Announcer DesignTech s Door Announcer is designed to alert you when a monitored ob jects like a door gate or cabinet are opened or moved CONTENTS Aa 2 Lithium Batteries CR2032 type Door Sensor white Remote Receiver white U a Double 2 Screws for Stick Foam Mounting Antenna AC Adapter INSTALLING THE BATTERIES IN THE Door Announcer 1 Insert a small screwdriver blade into the slot in the side of the case and gently pry up on each side of the case to open 2 Slip the first battery in the battery clip with the positive side up then slide the second battery on top of the first bat tery but under the clip making sure the positive sides of both batteries are face up Page 1 Door Announcer 30052 3 Push the case back together SETTING UP THE Door Announcer SENSOR The Door Announcer has a three position slide switch on the side of the unit 1 The position closest to the edge is the Silent Mode In this position the Door Announcer will make no sound when moved The Door Announcer will still send a signal to the Smart Home Receiver that the Door Announcer has been moved 2 The center position of the switch is the Door Chime Mode In this position the Door Announcer will chime each time the unit is moved and will automatically reset
Download Pdf Manuals
Related Search