Instruction Manual
Contents
1. If the cord is not long enough please use the One to One Power Cord to connect the Tube Pack to the Power Cord with Remote Control see Figure2 Step 3 Tightly wrap the Remote Control s Velcro around the Handlebar to securely place the Remote Control on the Handlebar see Figure3 HOW TO CONNECT THE HEADLIGHT WITH THE TUBE PACK gil Open the rubber cap at the rear of the Headlight and plug the Power Cord with Remote Control into the socket If the Power Cord is not long enough please use the One to One Power Cord provided to connect the Tube Pack to the Power Cord with Remote Control Wind the Cord around the frame and secure it with the Velcro Ties to ensure that it will not hinder riding HOW TO CONNECT THE HEADLIGHT WITH A TAILLIGHT TSL C Optional HOW TO OPERATE THE HEADLIGHT Press the POWER button on the Remote Control once to turn on the Headlight in high intensity mode Press again to turn it off Press the button a third time to turn on the Headlight in low intensity mode Press once more to turn off the light HOW TO REPLACE A LIGHT BULB Protective Len Bulb Module O Ring Protective Len Locking Tab Step 1 Push the locking tab inward to slide the Headlight out of the Bike Mount or Helmet Mount Step 2 Unscrew the Protective Len and take the O Ring off Step 3 Remove the old Bulb Module and replace it with a new light bulb Step 4 Put the O Ring back in place and tightly scr2. One to One Power Cord HOW TO INSTALL BATTERIES INTO TUBE PACK Tube Pack utilizes common AA batteries both rechargeable amp non rechargeable AA batteries are applicable Unscrew z E un Screw off the cap of the Tube Pack and place 4 x AA batteries correctly as shown into the Tube Pack Cover the cap and screw on it Note Do not mix new and old batteries Red LED indicator on the Remote Control shows low battery Red LED Indicator HOW TO INSTALL THE MAGNIFIER AND COLORED FILTER To install the Magnifier Colored Filters e Add the Magnifier or a Colored Filter in front of the Protective Len by turning it clockwise e Stack a Colored Filter on the Magnifier to achieve a colored wide beam effect Protective Len Magnifier Colored Filter HOW TO INSTALL THE HEADLIGHT Installing the Headlight on your Helmet Please see the illustration as follows Helmet Velcro Step 1 Use the Adhesive Shim provided to stick the Helmet Mount on the Helmet see Figure 1 Step 2 Secure the Helmet Mount with the Helmet Velcro provided see Figure 2 Step 3 Slide in the Headlight until an audible CLICK is heard see Figure 3 Step 4 Connect the Tube Pack and put it in your backpack If the cord is not long enough please connect the One to One Power Cord with the Tube Pack and the cord see Figure4 Installing the Headlight on your Bike Handle
3. Acumen Inc www vetta com e 2007 All Rights Reserved NANO LUX ae CE amp A revi ENGLISH READ INSTRUCTIONS BEFORE FIRST USE Nano LUX is powered by common AA batteries both rechargeable amp non rechargeable AA batteries are applicable Please thoroughly familiarize yourself with this manual and keep it for future reference FOR SAFE OPERATION IMPORTANT e Your Headlight and Tube Pack are splash proof and sealed to withstand wet weather conditions However do not place them under water deliberately e Avoid exposing the Headlight to be exposed to extremely hot or cold weather conditions e Securely connect the plug to avoid the Headlight accidentally turning off or the wire connection inadvertently falling out e The Headlight becomes hot when turned on Never touch the Headlight until it has cooled down Injury may result e The Headlight kit is not intended for use by children e Safely and properly dispose of the old battery according to your local regulations when it comes to the end of its useful life WHAT S IN THE PACKAGE Instruction Manual A Headlight J Helmet Velcro 2 pcs B Bike Mount K Tube Pack Velcro C Helmet Mount L Velcro Ties D Adhesive Shim M Screws 2 pcs E Bracket N Zip Ties F 4xAA batteries O Colored Filters 4 pcs G Tube Pack P Magnifier H Power Cord with Remote Control Q Instruction Manual
4. bar Please see the illustration as follows Handlebar Step 1 To tighten the Bike Mount on the Handlebar turn the knob clockwise until the Bike Mount firmly holds its position on the Handlebar see Figure 1 Step 2 Slide in the Headlight until an audible CLICK is heard see Figure 2 Step 3 Open the rubber cap of the Headlight Securely connect the Tube Pack with the Headlight by using the Power Cord with Remote Control provided Wind the Power Cord around the frame and secure it with the Velcro Ties to ensure that it will not hinder riding see Figure3 Step 4 Cut off the unwanted band see Figure 4 HOW TO INSTALL THE TUBE PACK AND REMOTE CONTROL Down Tube Zip Tie Handlebar Power Button eel Step 1 If your bike has Water Bottle Braze ons on the frame please follow the instructions to mount the Tube Pack onto the bike see Figure a Unscrew the Water Bottle Braze ons b Place the Bracket on the Down Tube and line it up with the holes c If you have a water bottle cage place the water bottle cage on top of the Bracket and then tightly screw the braze ons back on OR a If your bike does not have Water Bottle Braze ons then Tighten the Bracket on the Down Tube with Zip ties see Figure b Further secure the Tube Pack with the Tube Pack Velcro Step 2 Open the rubber cap at the end of the Tube Pack connector Connect the Tube Pack to the Power Cord with Remote Control
5. ed warranty does provide the original owner with certain legal rights and recourse The original owner may possess other rights or recourse depending on the state or country Please check the web to help answer any question and service manual CUSTOMER SERVICE CENTER Acumen Inc 101A Executive Dr Suite 100 Sterling VA 20166 USA Acumen Europe BV Spoordreef 25 27 1315 GK Almere The Netherlands Email customerservice vetta com Website www vetta com i os Fo Fa ne ee a a PT RE ee pn ge a OO EA We Om a ag On re Rr aa ee eee eee ee
6. ew the Protective Len back on to form a splash proof seal Step 5 Slide the Headlight into the Bike Mount or Helmet Mount You should hear an audible CLICK when it is properly locked into position Note When replacing a light bulb make sure the light bulb and Headlight have been thoroughly cooled off SPECIFICATIONS Dimension Temperature Headlight 43mmx50mm Operating at 15 C to 45 C Tube Pack 26 8mmx252mm BulbType Weight 3 7V 3 watt Solid State Emitter Headlight 55g Battery Type Tube Pack 150g AA batteries Operation Mode Life of the Bulb HIGH LOW Approx 8 000 hours continuous use Run Time Water Resistant Approx 10 hours Low Intensity Splash Proof Approx 5 hours High Intensity WARRANTY POLICY ACUMEN INC WARRANTS ALL VETTA The Company PRODUCTS AGAINST MANUFACTURER DEFECTS FOR A PERIOD OF 3 YEARS Subject to the following limitations terms and conditions components will be free of manufacturing defects in materials and workmanship The 3 year limited warranty is conditioned upon the components being used and operated in normal riding conditions This warranty does not cover normal wear and tear i e battery replacement broken wire rider abuse acts of God improper installation or product alteration This warranty is void if the components were not purchased new from or through an authorized VETTA retailer or dealer Examples of unauthorized dealers are online auction sites or online reta
7. ilers ACUMEN INC at its sole discretion will repair or replace items at its own cost Users are responsible for all freight and shipping charges when returning items for warranty service ACUMEN INC will pay the freight when returning serviced items via USPS or UPS to consumers or dealers once the item s has been repaired or replaced REQUIREMENTS FOR WARRANTY SERVICING 1 Prior to shipping an item back you must first obtain a Return Authorization Number s RA Each item being returned must have an individual RA 2 To obtain an RA you must either contact the retailer where the product was originally purchased from or contact VETTA directly at customer service vetta com 3 For trouble shooting purposes we request that the complete unit with packaging be returned to ACUMEN INC unless otherwise stated by VETTA representative ITEMS TO BE INCLUDED IN RETURNS 1 The defective product s 2 A letter clearly stating the problem s with the returned item s 3 Copy of the original sales receipt showing proof of purchase date 4 The Company is not responsible for loss or additional damages while in transit to ACUMEN INC 5 Clearly mark the RA on the outside of the return packaging All items without an RA will be refused and returned to the return address on the package The Company shall not be held responsible for replacing items with new items for greater than the amount of the original item purchase price This limit
Download Pdf Manuals
Related Search