Bromic Tungsten Portable Patio Heater Owner`s Manual
Contents
1. www bromicheating com INSTALLATION INSTRUCTIONS conrinueo STEP 4 Secure the rear arms to front assembly using 2 x M8 x 16mm screws and supplied M8 Hex Key STEP 5 Secure the side panels to frame using 12 x G8 screws A Phillips screw driver is required for this step NL Repeat for opposite side www bromicheating com INSTALLATION INSTRUCTIONS conrinueo STEP 6 Slide top arms over front assembly slip joints Ensure top screw holes are faced inwards Secure the front panel to top arms using 4 x M5 screws and supplied M5 Hex Key N Zo Note The joint between the lower and upper arms is firm to ensure rigidily and stability of the product To engage slowly lever the two sections together using some force and push down fully STEP 7 Secure the top arms to lower arm slip joint using 2 x M8 x45 screws and supplied M8 Hex Key www bromicheating com INSTALLATION INSTRUCTIONS conrinueo STEP 8 Lay both heater head and stand on anon abrasive surface as shown Two people are required for this step NON ABRASIVE SURFACE STEP 9 Feed gas hose through arm slot and push through until it reaches slot in bottom arm Keep feeding hose until all slack is taken up2. 5 Push in and hold control knob whilst simultaneously press ing the spark ignite button Continue to hold in the controls for 10 seconds for ignition to complete 6 When appliance is correctly turned on the tiles Release the controls If the heater has not ignited wait will start to glow red 5 minutes and then repeat Step 5 TURNING THE APPLIANCE OFF 1 Press and turn the control knob to OFF position to stop the supply of gas to the burner The tiles should change colour from red to black 2 Turn OFF the gas supply at the LPG storage bottle www bromicheating com MAINTENANCE AND SERVICING It is important that regular maintenance is carried out on the heater to maintain efficient operation All maintenance should be carried out ONLY by authorized service personnel Inspect and clean at least every six months or more frequently in adverse conditions Never obstruct the flow of combustion and ventilation air Always keep the appliance area clear and free from combustible materials gasoline and other flammable vapors and liquids Do not clean heater with cleaners that are combustible or corrosive REGULAR SERVICE REQUIREMENTS 1 The whole gas system hose assembly regulator pipes and burner should be inspected for damage and leaks before each use and at least annually by an authorized person for t
3. www bromicheating com INSTALLATION INSTRUCTIONS conrinueo STEP 10 Secure the heater head to arms using 4x M8 screws and supplied washers with M8 Hex Key S STEP 13 Return heater to upright position Two people are required for this step NON ABRASIVE SURFACE www bromicheating com INSTALLATION INSTRUCTIONS conrinueo STEP 14 SHER IS Screw regulator assembly Place gas bottle into lower enclosure and fasten to gas bottle strap tightly STEP 16 Pull sleeve back on regulator connector insert hose fitting amp release sleeve on regulator STEP 17 connector Lower gas bottle bracket into position l www bromicheating com INSTALLATION INSTRUCTIONS conrinueo STEP 18 Secure deflector to heater by loosening the two screws and secure brackets underneath washers Re tighten screws to original position using screw driver Pa STEP 19 Unscrew igniter cap Insert supplied AAA battery into cap and re scew to original position STEP 20 Perform Gas leakage test as shown on page 20 ie 6 www bromicheating co
4. normal when the burner is ignited or extinguished This appliance is not intended for use by young or infirm persons unless they have been adequately supervised by a responsible person to ensure that they can use the appliance safely Check for damage to the appliance regularly If damage to the appliance is suspected discontinue use immediately and contact the supplier or qualified person for repair Avoid inhaling fumes emitted from the heater s first use Smoke and odour from the burning of oils used in manufacturing will appear Both the smoke and odour will dissipate after approximately 30 minutes The pressure regulator and hose assembly supplied with the appliance must be used Replacement regulator and hose assemblies must be purchased from Bromic Heating Pty Ltd Storage of an appliance indoors is permissible only if the cylinder is disconnected and removed from the appliance A cylinder must be stored outdoors in a well ventilated area out of the reach of children A disconnected cylinder must have dust caps tightly installed and must not be stored in a building garage or any other enclosed area Do not store a spare LP gas cylinder under or near this appliance Never fill the cylinder beyond 80 full www bromicheating com PRODUCT OVERVIEW PRODUCT DESCRIPTION The TUNGSTEN Gas Radiant Heater is designed to provide effective outdoor heating to both commercial and residential premises whilst offering an a
5. the soapy water solution to the 3 connections illustrated below e To check connection 3 the gas control knob must be pressed in to open the gas valve e If bubbles appear at any of the connections there is a gas leak e If a gas leak is detected turn off the gas supply Tighten any leaking fittings and repeat process described above e If soap bubbles still appear gas is still leaking turn off the gas supply at the cylinder disconnect the regulator from the gas cylinder and contact the store of purchase for assistance and advice e If gas connections are gas tight the heater is ready to www bromicheating com OPERATING INSTRUCTIONS A WARNING Do not turn the heater on with people standing in front of heater TU RN NG TH E AP PLIANCE ON Heater must be turned on while standing behind the heater 1 Ensure that installation has been carried out in accordance UN WARNING with the manufacturers instructions outlined in this document Improper lighting procedures can cause personal injury property damage or even death 2 Test the spark ignite button is working correctly by pressing the button and observing sparks at the ignition rods at the front ofthe heater If sparks are not observed do not proceed with turning appli 3 Turn ON the gas supply at the LPG storage bottle ance on Contact the store of purchase for assistance and advice 4 Turn on gas control knob to maximum setting
6. For service questions please contact Bromic at 1 800 301 1293 For sales inquiries contact Sylvane at 1 800 934 91914 BR MIC HEATING TUNGSTEN SMART HEATTM PORTABLE HEATER BY BROMIC INSTALLATION INSTRUCTION AND SERVICE MANUAL SUITABLE FOR GAS RADIANT HEATER MODELS TUNGSTEN SMART HEATTM A WARNING Do not store or use petrol or other flamable vapor and liquids in the vicinity of this or any other appliance An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance A WARNING Improper installation adjustment alteration service or maintenance can cause property damage injury or death Read the installation operating and maintenance instructions thoroughly before installing or servicing this equipment A DANGER If you smell gas Shut off gas to the appliance Extinguish any open flame If odour continues keep away from the INNI appliance and immediately call your gas supplier or fire department A WARNING For Outdoor Use Only Version 1 3 USA Can A IMPORTANT This manual contains important information about the assembly operation and maintenance of TUNGSTEN Smart Heat M Heaters Please pav close attention to the important safetv information shown throughout this instruction manual Anv safetv information will be accompanied bv the following safety alert symbols NDANGER AWARNING IMPORTANT READ THIS MANUAL CAREFULLY before installing or s
7. d unrestricted ref Appendix A Example 4 Note The definition of outdoors is an above ground open air situation with natural ventilation without stagnant areas where gas leakage and products of combustion are rapidly dispersed by wind and natural convection GAS REQUIREMENTS TUNGSTEN Smart Heat LPG Model e Use Propane LPG gas cylinder only e The approved manifold pressure to the appliance is 10 W C The MIN inlet pressure to the appliance is 11 W C The MAX inlet pressure to the appliance is 14 W C IMPORTANT The LPG gas cylinder must be Constructed and marked in accordance with the Specifications for LP gas cylinders of the U S Department Transportation DOT or the Standard for Cylinders Spheres and Tubes for Transportation of Dangerous Goods and Commission CAN CSA B339 as applicable Provided with a listed overfilling prevention device and Provided with a cylinder connection device compatible with the connection for the appliance Cylinder must have include a collar to protect the cylinder valve www bromicheating com INSTALLATION REQUIREMENTS continuen LOCATION CLEARANCES When selecting the location for the TUNGSTEN Gas Patio Heater the following clearances should be followed Care should be taken to ensure that the heater is not installed e Where heat ignition can cause damage to gas cylinders lines e Near other combustible materials e In open locations subject to rain Note Heater
8. ervicing this product e Installation and repair should be done by a qualified service person e The heater should be inspected before use and at least annually by a qualified service person Improper installation operation or maintenance can result indeath severe injury or property damage e This manual must be left with the consumer following installation amp the consumer must retain them for future reference BROMIC HEATING Head Office 13223 Black Mountain Rd Suite 1305 San Diego California 92129 United States Telephone 1 800 301 1293 Fax 61 2 9748 4289 Email info bromicheating com Web www bromicheating com Note Bromic Heating Pty Ltd reserves the right to make changes to specifications parts components and equipment without prior notification This Installation operation and service manual may not be reproduced in any form without prior written consent from Bromic Heating Pty Ltd www bromicheating com CONTENTS IMPORTANT NOTES amp WARNINGS PRODUCT OVERVIEW PRODUCT DESCRIPTION SPECIFICATIONS GENERAL INFORMATION PRODUCT FEATURES INSTALLATION REQUIREMENTS GAS REQUIREMENTS INSTALLATION CLEARANCES INSTALLATION INSTRUCTIONS HEATER INSTALLATION INSTRUCTIONS LEAKAGE TEST OPERATING INSTRUCTIONS TURNING THE APPLIANCE ON TURNING THE APPLIANCE OFF MAINTENANCE AND SERVICING TROUBLE SHOOTING APPENDIX A www bromichea
9. g codes and any other relevant statutory regulations are carried out Certain materials or items when stored under or near the appliance will be subjected to radiant heat and could be seriously damaged The whole gas system hose assembly regulator pipes and burner should be inspected for damage and leaks before each use and at least annually by an authorized person for the life of the heater The hose assembly must be replaced prior to the appliance being put into operation if there is evidence of excessive abrasion or wear or if the hose is damaged The replacement hose must be purchased from Bromic Heating Pty Ltd All leak tests should be done with a soap solution Never use an open flame to check for leaks Do not use the heater until all connections have been leak tested by an authorised person This radiant heater is NOT intended to be installed on recreational vehicles and or boats Improper installation adjustment or alteration can cause personal injury property damage or even death Do not attempt to alter the unit in any manner Do not paint any surface of the heater or top canopy reflector Burner and circulation air passageways of the heater must be kept clean Frequent cleaning may be required as necessary Turn Gas Supply off when not in use Check the heater immediately if any of the following occurs The heater does not reach temperature The burner makes popping noise during use a slight noise is
10. he life of the heater To check the gas hose within the mounting arm disassemble heater by reversing the installation instructions as outlined in installation section of this manual The hose assembly must be replaced prior to the appliance being put into operation if there is evidence of excessive abrasion or wear or if the hose is damaged The replacement hose must be purchased from Bromic Heating Pty Ltd VISUALLY CHECK BURNER FLAMES During heaters function visually check that all burners are alight and glowing hot This can be done by observing the red glow through the translucent face or by peering down the product combustion passageway Note A slight variation in colour is to be expected Clean burners Burners can be cleaned by directing compressed air max20PSI at outlet ports Avoid directing air at gasket material between ceramic tile and burner cup Clean manifold and injectors Undo gas hose from gas valve outlet heater should be switched off and inject compressed air max20PSI down the inlet fittings Clean dust and foreign matter from inside of heater housing Open up rear housing and clear dust using compressed air max20PSI and a damp cloth Remove debris spider and insect nests from control compartment burner and circulation air passageways of the heater with heavy duty pipe cleaner or compressed air to keep appliance clean and safe for use Never clear ports or other openings with toothpicks or other article
11. he outdoor heating industry by introducing ground breaking benefits never seen before in traditional gas or electric heaters TUNGSTEN heaters have set the industry benchmark with stylish good looks and world first innovation TUNGSTEN heaters excel in the areas of e Aesthetic appeal e Innovation e Performance Flexibility e Cost effectiveness For more detailed product information visit www bromicheating com www bromicheating com INSTALLATION REQUIREMENTS A IMPORTANT Installation and repair should be done by a qualified service person The heater should be inspected before use and at least annually by a qualified service person This appliance shall only be used in above ground open air situations with natural ventilation without stagnant areas where gas leakage and products of combustion are rapidly dispersed by wind and natural convection Any enclosure in which the appliance is used shall comply with one of the following 1 An enclosure with walls on all sides but at least one permanent opening at ground level ref Appendix A Example 1 Within a partial enclosure that includes an overhead cover and no more than two walls ref Appendix A Example 2 Within a partial enclosure that includes an overhead cover and more than two walls the following shall apply e Atleast 25 of the total wall area is completely open ref Appendix A Example 4 and e At least 30 of the remaining wall area is open an
12. he remaining wall area is open and unrestricted OUTDOOR AREA EXAMPLE 5 www bromicheating com
13. m INSTALLATION INSTRUCTIONS conrinueo STEP 21 The back cover is secured by magnets Firstly position slots in back cover over the two hooks then lower cover to allow magnets to catch www bromicheating com INSTALLATION INSTRUCTIONS conrinueo Adjusting the heater head angle CAUTION ONLY ADJUST THE HEATER HEAD ANGLE PRIOR TO OPERATION ADJUSTING WHILST UNIT IS IN OPERATION OR POST OPERATION CAN CAUSE SERIOUS BURNS To set heater head angle at high position manually push heater head up to align hole then insert slip pin To set heater head angle at low position remove slip pin amp allow heater head to rest in low posi tion Slip pin does not need to be inserted www bromicheating com INSTALLATION INSTRUCTIONS conrinuep LEAK TEST Gas connections on heater are leak tested at the factory prior to shipment A complete gas leak test must also be performed after assembly before operating the heater due to possible damage occurring during transportation e Never leak test while smoking e The heater must be checked with a full gas cylinder e Ensure connection all 3 connections illustrated below are connected correctly amp tight e Make sure the control knob is in the OFF position e Make a mild soapy water solution The soapy solution can be applied with a spray bottle or soft cloth e Turn on the gas supply at the gas cylinder e Apply
14. ppealing design The heater incorporates a pivoting head and adjustable heat output for precise heat control The heater has been designed to withstand the rigors of the outdoors SPECIFICATIONS TUNGSTEN Smart Heattn O Gas Type Propane Gas LPG only Gas Supply 20Lb 9kg LP Gas Cylinder Safety features Flame failure device anti tilt switch Gas supply pressure Min 11 wc Max 14 wc TUNGSTEN SMART HEAT HEATER DIMENSIONAL DETAILS 2160mm 7 1ft II ul A IMPORTANT This appliance is to be protected from rain Install under a protective cover This appliance shall only be used in an above ground open air situation with sufficient natural ventilation The heater must not be operated in any stagnant areas and should be positioned where any potential gas leakage and products of combustion are rapidly dispersed by wind and natural convection www bromicheating com PRODUCT OVERVIEW continuep GENERAL INFORMATION The TUNGSTEN Gas Patio Heaters are suitable for outdoor spaces In addition to the installation Instructions provided authorized installers must abide by local codes or in the absence of local codes with the National Fuel Gas Code ANSI Z223 1 NFPA 54 Natural Gas and Propane Installation Code CSA B149 1 or Propane Storage and Handling Code B149 2 Please note that these standards are subject to change PRODUCT FEATURES TUNGSTEN Gas Patio Heaters are revolutionizing t
15. rised service authorised technician technician can do Burner will not e Gas valve may be OFF e Turn the gas valve ON Refill LPG tank light e Tank fuel empty e Checkall fittings Remove and clean e Opening blocked e Loose connections e Replace cylinder with a new Replace thermocouple e Low gas pressure cylinder e Thermocouple bad e Not in correct location Burner will not stay Loose connections e Tighten connections Clean dirty area e Thermocouple bad e Check connections on Replace thermocouple e Gas leak in line e Lack of fuel pressure Refill LPG tank e Tank near empty Burner flame is low Supply hose is bent or e Straighten hose and perform twisted leak test on hose Emitter glows e Low gas pressure e Replace cylinder with a new uneven e Base is not on a level cylinder surface e Place heater on a level surface Thick black smoke Blockage in burner e Turn off the heater and let it Remove blockage and cool clear burner inside and outside Carbon build up e Dirt or film on reflector e Clean reflector and flame and flame screen screen www bromicheating com APPENDIX A CONTINUED Both ends open OUTDOOR AREA EXAMPLE 3 Open side at least 25 of total wall area 30 percent or more in total of the remaining wall area is open and unrestricted OUTDOOR AREA EXAMPLE 4 www bromicheating com Open side at least 25 of total wall area NY LIN 30 percent or more in total of t
16. s that will break and block the ports In a salt air environment such as near an ocean corrosion occurs more quickly than normal Remove salt spray from the heater immediately to prolong heater life Check frequently for corroded areas and repair them promptly The exterior components of the heater are constructed from stainless steel and high temperature black paint Over the life of the heater internal non painted parts may slightly discolour from high temperatures emitted by the heater This is a normal occurrence and does not affect the operation of the appliance 10 Replacement parts can be purchased to restore the heater to its original appearance from Bromic Heating Pty Ltd Z IMPORTANT Installation and repair should be done by a qualified service person The heater should be inspected before use and at least annually by a qualified service person More frequent cleaning may be required as necessary It is imperative that control compartment burners and circulating air passageways of the heater be kept clean A IMPORTANT Do not apply any additional surface coating to the heater under any circumstances Use of additional coating other than those applied during manufacture could result in hazardous reactions such as toxic fumes or fires Additional coatings will void the warranty www bromicheating com TROUBLESHOOTING What you can do What ONLY an Problem Possible cause if these do not work contact an autho
17. should be installed in such a way so as to allow adequate e Clearance around air openings to combustion chamber e Clearance from combustible material e Provisions for accessibility and clearance for combustion and ventilating air supply A IMPORTANT This appliance must onlv be used in a well ventilated area When selecting the installation location for the Tungsten Smart Heat Portable the following clearances should be followed www bromicheating com INSTALLATION INSTRUCTIONS CONTENTS PACKED IN 2 BOXES Box 1 Contents Head Assembly AAA Battery Box 2 Contents Top Flame Deflector Regulator www bromicheating com INSTALLATION INSTRUCTIONS conrinueo Supplied Fasteners M8 x 95mm M8 x 45mm M8 x 16mm QTY 2 QTY 2 N FIN M8 x Washer QTV 4 zen N A k J a Supplied Tools M8 Hex Key Tools Not Included Phillips head screw driver and Spray Bottle www bromicheating com INSTALLATION INSTRUCTIONS conrinueo STEP 1 Unpack boxes and place all items on a non abrasive surface STEP 2 Fasten rear arms to base using 2 x M8 20mm screws and the supplied M8 Hex Key f a STEP 3 Position front assembly and fasten using 2 x M8 20mm screws using supplied M8 Hex Key rali f
18. ting com IMPORTANT NOTES AND WARNINGS A WARNING Failure to follow the warnings and instructions in this manual could result in severe personal injury death or property damage Installation and repair should be done by a qualified service person The heater should be inspected before use and at least annually by a qualified service person Do not use or store flammable materials near this appliance Do not spray aerosols or flammable materials in the vacinity of this appliance while it is in operation Any guard or other protective device removed for servicing conducted by an authorised person must be replaced before operating the heater Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition Children should be carefully supervised when they are in the area of the heater Clothing or other flammable materials should not be hung from the heater or placed on or near the heater Do not perform maintenance until heater has been turned off and heater temperature has cooled to room temperature Do not expose the burner to water or moisture The appliance must be protected from rain Do not use the heater if any of these parts are exposed to water until the appliance is inspected or repaired by an authorised service person The installer is to ensure that the requirements of the local authority local gas fitting regulations municipal buildin
Download Pdf Manuals
Related Search