Hydraulic Transmission Jack
Contents
1. Repeat for the other three wedges Chain Insert the bolt through one hole of the saddle assembly lowest to the ground if accessible If the assembly is extended insert the bolt through one hole of the adjustment plate Secure with washer and wingnut BEFORE USE 1 Verify that the product and the application are compatible if in doubt call Hein Werner Technical Service 816 891 6390 2 Read the operator s manual completely and familiarize yourself thoroughly with the product its components and recognize the potential hazards associated with its use before using this product 3 Lower saddle fully locate and remove oil filler plug This will help to release any pressurized air that may be trapped within the reservoir 4 Ensure the oil level is within 3 16 from the inner cylinder as viewed from the oil filler hole Reinstall oil filler plug 5 Replace worn or damaged parts and assemblies with Hein Werner replacement parts only Lubricate as instructed in Maintenance Section Study understand and follow all printed materials provided with on this product before use Do not exceed rated capacity Use only on hard level surfaces capable of supporting rated capacity loads Use of this jack is limited to the removal installation and transportation of transmissions transfer cases and transaxles Do not use a transmission jack to tilt or support a vehicle e Ensure the center gravity of load is centered on the saddle2. e For your safety do not exceed 10 degree tilt angle of the saddle assembly in all directions e Adequately support the vehicle before servicing e Use only chains slings attachments and or adapters supplied by the manufacturer If loaded jack must be moved make sure that the load is secured stable and in lowest position e Transfer load immediately to appropriate support device for service or repair e Shock loads may cause the sudden loss of load and or cause the jack to tip or flip over violently bend or break e No alterations shall be made on this product Failure to heed these markings may result in personal injury and or property damage e Leer comprender y seguir las instrucci nes antes de utilizar el aparato e El manual de instrucci nes y la informaci n de seguridad deben estar comunicado en lengua del operador antes del uso e No seguir estas indicaci nes puede causar da os personales o materiales OPERATION see Fig 1 amp 3 Raise Saddle Assembly 1 Locate and close release valve by turning it clockwise firmly then pump the handle until the load is contacted 2 Follow vehicle manufacturers recommended procedures for removing the load as outlined in vehicle service manual or repair guide 3 Secure load with provided chains Important Ensure the transmission is centered on the jack An off center transmission could cause the jack to tip over resulting in personal injury or proper
3. HEIN WERNER AUTOMOTIVE Hydraulic Transmission Jack Operating Instructions amp Parts Manual Model Number Capacity HW93718 1 Ton Made in the U S A At is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death SFA Companies 10939 N Pomona Ave Kansas City MO 64153 customerservices heinwerner automotive com Read this manual and follow all the Safety Rules and Operating Instructions before using this product HW93718 M1 rev 09302009 SAFETY and GENERAL INFORMATION Save these instructions For your safety read understand and follow the information provided with and on this jack The owner and operator of this equipment shall have an understanding of this jack and safe operating procedures before attempting to use The owner and operator shall be aware that use and repair of this product may require special skills and knowledge Instructions and safety information shall be conveyed in the operator s native language before use of this jack is authorized If any doubt exists as to the safe and proper use of this jack remove from service immediately Inspect before each use Do not use if there are broken bent cracked or damaged parts including labels Any jack that appears damaged in any way operates abnormally or is missing parts shall be removed from service immediately If the jack
4. has been or suspected to have been subjected to a shock load a load dropped suddenly unexpectedly upon it immediately discontinue to use until jack has been checked by a Hein Werner authorized service center contact distributor or manufacturer for list of Authorized Service Centers It is recommended that an annual inspection be done by qualified personnel Replace worn or damaged parts with Hein Werner Authorized Replacement Parts only Labels and Operator s Manuals are available from manufacturer PRODUCT DESCRIPTION Hein Werner Hydraulic Transmission Jack is designed to be used as an aid in the removal and installation of automotive and light truck transmissions transfer cases and transaxles This jack is for use under portable lift equipment where vehicle must be supported by a pair of appropriately rated vehicle stands A DO NOT use for any purpose other than those uses outlined above SPECIFICATIONS Expanded Jack i Gross Papacy p o saddle Dasa Saddle Area Bal aa aan HW93718 Ton Ton y 44 18 9716 x 12 3 8 9 16 x 18 9 16 x 12 3 8 3 8 20 1 2 x 18 1 2 47 112 x28 47 112 x28 x 28 309 tb Ib Wedge Saddle Plate Lifting Arm Oil Filler Plug Release not shown Valve not shown Tilt Adjustment Knobs Figure 1 Model HW93718 Nomenclature ASSEMBLY Wedges Align the hole in the wedge with the hole in the saddle assembly Secure with the nut washer and bolt
5. 196 Ball H0218000 N A 209910 248908 248909 245546 210311 245892 Indicates items included in Repair kit 245892 1 1 1 1 1 1 1 1 1 1 4 4 1 1 1 1 1 1 SFA Companies 10939 N Pomona Ave Kansas City MO 64153 816 891 6390 customerservices heinwerner automotive com
6. HE REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS AS DESCRIBED ABOVE 2 SFA COMPANIES SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGE OR LOSS WHATSOEVER 3 ANY IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO TWO YEARS OTHERWISE THE REPAIR REPLACEMENT OR REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED 4 ANY MODIFICATION ALTERATION ABUSE UNAUTHORIZED SERVICE OR ORNAMENTAL DESIGN VOIDS THIS WARRANTY AND IS NOT COVERED BY THIS WARRANTY Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state SFA Companies 10939 N Pomona Ave Kansas City MO 64153 816 891 6390 customerservices heinwerner automotive com Model HW93718 Replacement Parts Frame ty J m v mma Ep o AU HU 33 Figure 2 Parts Illustration for Model HW93718 Frame Item Part Description Qty 8 NA Washer 6 4 N A HexHd Cap Screw 6 5 NA YokeClamp 2
7. e N A Washer _ 4 r NA HexNut oa 8 N A Adj YokeRod 2 9 N A__ Adj Yoke Bracket 1 10 N A__ AdjustingScrew 4 a a pn a a n 18 f 656700 Pin Forward it 1 16 5879600 Washer 2 20 221798 Retaining Ring 2 zt Rzzt5500 Pin Forward it 1 Adj Screw Assy Indicates items included in Attachment kit HW93249 RO PI item Part 51 H2ss5000 Bok 32_ H1103000 Washer 8 38 42638600 Hex nut 8 54 203301 jamn a 56 40249060 Bearings 4 56 245395 Caster Assembly 4 57 Na FrameAssemby 1 a R A gt H2214500 Pin Side Anchor 1 H6599600 Pin Side Tit 1 H0762000 Adj Screw Assy Side 1 46 H6662700 Rivet J1 47 H6598900 Main PivotPin 1 48 H1308500 Retaining Ring 2 49 226318 GreaseFitting 1 50 H6665200 Open EyeBolt 1 51 H2524500 Washer __ 1 52 H6665300 WingNut 1 53 248472 Button Head Hex 4 Screw HW93249 Attachment Kit e eje N lt Model HW93718 Replacement Parts Hydraulic Unit ltem Part Description Qty 8 245583 Cylinder 1 2 H6599200 OilTank 1 Balt Bal tC Pug tt Valve Seal 1 Spring 1 Ho391000 U Cup 1 201733 Expansion Plug 1 226373 Adjusting Nut 1 226378 Spring 1 226376 SpringCup 1 CE EM NEM a EA za EM EG mi 245845 Bolt 203
8. ghtly closed e Overload condition e Remedy overload condition Jack will lift but not maintain pressure e Release valve not tightly closed e Overload condition e Hydraulic unit malfunction e Reservoir overfilled Jack will not lower after unloading e Linkage binding e Fluid level low e Air trapped in system Poor lift performance Jack will not lift to full extension e Ensure release valve tightly closed e Remedy overload condition e Contact Tech Service e Ensure load is removed then drain fluid to proper level e Clean and lubricate moving parts e Ensure proper fluid level e With saddle fully lowered remove oil filler plug to let pressurized air escape then reinstall oil filler plug e Fluid level low e Ensure proper fluid level HEIN WERNER_ AUTOMOTIVE TWO YEARS LIMITED WARRANTY For a period of two 2 years from date of purchase SFA Companies will repair or replace at its option without charge any of its products which fails due to a defect in material or workmanship under normal usage This limited warranty is a consumer s exclusive remedy Performance of any obligation under this warranty may be obtained by returning the warranted product freight prepaid to SFA Companies Warranty Service Department 10939 N Pomona Ave Kansas City MO 64153 Except where such limitations and exclusions are specifically prohibited by applicable law 1 THE CONSUMER S SOLE AND EXCLUSIVE REMEDY SHALL BE T
9. supply annually 1 With saddle fully lowered and pump piston fully depressed remove oil filler plug 2 Lay the jack on its side and drain the fluid into a suitable container Note Dispose of hydraulic fluid in accordance with local regulations 3 Set jack in its level upright position and fill with oil until 3 16 above the inner cylinder as seen from the oil filler hole Reinstall oil filler plug TROUBLESHOOTING Symptom Possible Causes Lubrication A periodic coating of light lubricating oil to pivot points axles and hinges will help to prevent rust and assure that wheels castors and pump assemblies move freely Cleaning Periodically inspect the ram for signs of rust or corrosion Clean as needed and wipe with an oily cloth Note Never use sandpaper or abrasive material on these surfaces Storage When not in use store the jack with ram fully retracted REPLACEMENT PARTS refer to page 6 amp 7 Not all components of the jack are replacement items but are illustrated as a convenient reference of location and position in the assembly sequence When ordering parts give model number part number and parts description Call or write for current pricing Hein Werner Customer Support 10939 N Pomona Ave Kansas City MO 64153 Phone 816 891 6390 E mail customerservices heinwerner automotive com Corrective Action Jack will not lift load e Release valve not tightly closed e Ensure release valve ti
10. ty damage For your safety do not exceed 10 degree tilt angle of the saddle assembly in all directions To avoid crushing and related injuries NEVER work on under or around a load supported only by jack Immediately transfer the load to an appropriate work station Lower Saddle Assembly Be sure all tools and personnel are clear before lowering load Dynamic shock loads are created by quickly opening and closing the release valve as the load is being lowered The resulting overload may cause hydraulic system failure 1 Secure the load to the jack with provided chain 2 Slowly gently turn release valve counter clockwise to lower load No more than 1 2 full turn until load is fully lowered 3 Immediately transfer the load to an appropriate repair fixture MAINTENANCE Important Use only a good grade hydraulic jack oil Avoid mixing different types of fluid and never use brake fluid turbine oil transmission fluid motor oil or glycerin Improper fluid can cause failure of the jack and the potential for sudden and immediate loss of load We recommend Hein Werner HW93291 or equivalent hydraulic jack oil Adding Oil 1 With saddle fully lowered set jack in its upright level position Locate and remove oil filler plug 2 Fill with oil until 3 16 above the inner cylinder as seen from the oil filler hole Reinstall oil filler plug Changing Oil For best performance and longest lift replace the complete fluid
Download Pdf Manuals
Related Search