Samsung VC-U366 User Manual
Contents
1. J attached Reach Handle slide the the Handle is flush Insert one screw provided from the screw packet into the existing hole Tighten securely with a Philliphs head screwdriver Slide the Extension Wand and the Crevice Tool together into the storage clip as shown Hose Wand is firmly Slide the Dusting Brush Tool into the storage clip as shown 7 2 How to use you samsung vacuum 1 To turn cleaner ON I press the ON OFF switch to the ON position 2 To the cleaner OFF O press the ON OFF switch to the OFF position The cleaner can also be moved by using the carrying handle AN CAUTION The Rotating Floor Brush continues to rotate while tools are in use To reduce the risk of injury from moving parts always move the cleaner with the Carrying Handle at the back of the cleaner Always place vacuum cleaner on floor with Handle in Upright position when using tools Never place your fingers under the cleaner when it is running Never place Powerfoot on furniture or uneven surfaces Do not place vacuum cleaner close enough to objects to pull them into rotating brush The handle of your cleaner has three positions upright for storage and when using cleaning tools operating for general operation on carpet and floors low for reaching under low furniture Step on handle release pedal to lower handle Attachment tools can be used to clean furniture or drapes on stairs2. OFF and disconnect plug from electrical outlet before performing mainte nance or troubleshooting checks Stand on one end of rug and move cleaner toward other end or edge Before reaching edge push down on handle This will lift up the nozzle front of Cleaner and will prevent rug from clinging to cleaner Continue to lift front of cleaner so that when you have reached the edge it is completely off the rug Move cleaner back to start again lower front of cleaner and use only forward strokes Carpet and rug cleaning takes place at the nozzle A When it is necessary to raise and lower the nozzle for various carpet pile heights rotate the nozzle control knob B to the desired setting For maximum cleaning performance The following carpet height settings are recommended Lowest setting for all types of carpet Higher settings for very deep pile carpet where easier pushing effort is desired while maintaining good cleaning performance Note If the cleaner is difficult to push rotate knob to the next higher setting To change the power level of the vacuum cleaner rotate the knob The Dirt Container needs to be emptied when the dirt reaches the Full line on the side of the Container Unplug the cleaner from electrical outlet Slide the Lock n Seal Lever to the Unlock position Grasp handle and pull the Dirt Container straight out to remove from vacuum Empty dirt into garbage cont
3. The Pre Motor Filter protects the motor from dirt particles It is located in the slide out tray underneath the Dirt Container If the filter becomes dirty pull out the tray lift out the filter and clean The Post Motor Filter assists in the filtration process to return clean air to the room It is located behind the door on the side of the cleaner If the filter becomes dirty open the door remove the filter and clean Note A white pleated HEPA Media Filter is offered as an optional item This filter is not washable and must be replaced N WARNING Do Not operate cleaner with damp or wet filters or without all filters in place Disconnect cleaner from electrical outlet Place handle in low position and turn cleaner over so bottom side is up Remove the 4 screws as shown with a screw driver With lettering on outside of belt and positioned as shown in box on D slide new belt over motor pulley B A VSG 3 9 War 7 77 Insert agitator through belt and place belt in belt guide C on agitator Should the agitator shield D become dislodged while replacing the belt or the agitator reposition it as shown noting the placement of its belt guide D A 3 1 o 4 Grasp agitator firmly and fit it into Reposition bottom plate and 4 position by first sliding the end opposite screws Tighten screws securely the belt into the rectangular slot F on side of cleaner Pu
4. Vacuum Cleaner For Household use Only Operating Instructions A A w SS 5 z A A SS A Read these instructions before operating the vacuum cleaner x The design and specification may be different depending on the models Register your product at www samsung com global register Thank you for purchasing a Samsung vacuum cleaner When using an electrical appliance basic precautions should always be followed including the following PLEASE READ ALL WARNINGS AND INSTRUCTIONS BEFORE USING THIS APPLIANCE ORE a To reduce the risk of fire electric shock or injury Do not leave appliance unattended when plugged in Unplug the vacuum from the outlet when it is not in use or when it is being cleaned Do not use outdoors or on wet surfaces Do not allow to be used as a toy Close attention is necessary when used by or near children Use only as described in this manual Use only manufacturer s recommended attachments Do not use with damaged cord or plug If appliance is not working as it should or has been dropped damaged left outdoors or dropped in water take it to a service center Do not pull or carry the vacuum by the cord or use the cord as a handle Do not close a door on cord or pull the cord around sharp edges or corners Do not run the appliance over its cord Keep the cord away from heated surfaces Do not unplug the vacuum by pulling on the cord To unplug grasp
5. ainer Put the Dirt Container back in the vacuum and slide the lever to the Lock position Unplug the cleaner from electrical outlet The Upper Tank Filter can be reached by removing the Dirt Container reaching underneath the Upper Tank and turning the rim of the Filter Frame to unlock Pull straight down to remove Brush the dirt off the Louvers and Upper Tank Filter The foam Upper Tank Filter may be removed and hand washed in cold water with mild detergent Rinse well then air dry thoroughly before replacing The Upper Tank and Louvers may also be wiped clean with a damp cloth Note The Dirt Container may be washed in warm water with a mild detergent Make sure it is completely dry before using again Note For easier access the entire Upper Tank may be removed by turning the knob on the back of the cleaner to unlock and pulling the entire tank straight out The belt on your cleaner causes the agitator to rotate and is important for the effective operation of the cleaner The belt is located under the bottom plate of the cleaner and should be checked from time to time to be sure it is in good condition Disconnect cleaner from electrical outlet To check belt remove bottom plate as shown in How to replace Replace belt it is stretched cut or broken TEF CIS 3 7 Ne S y TA na e Remove agitator and used belt Discard used belt Post Motor
6. any way Assembled Vacuum Cleaner Parts The assembled cleaner will look like the illustration to the left Crevice Tool Upper Tank Knob Extension Wand Dusting Brush WARNING Hose Clip Stretch Hose Quick Release Cord Wrap Carrying Handle Quick Reach Handle Hose Wand cs Ss is l Ce NG ay L a Hose Wand Base Louvers Power Cord Dirt Container Pre Motor Filter Height Adjustment Knob Power Switch Upper Tank Frame and Filter Inside Louvers Upper Tank Post Motor Filter Hepa Media Filter 4 Optional Item Powerfoot gt Release Pedal Furniture Protection Guard OPERATE THE VACUUM CLEANER ONLY AT THE VOLTAGE SPECIFIED ON THE NAMEPLATE Locate the vacuum screw packet taped to Stand the vacuum upright and slide the Handle and remove the the base of the Handle Check to be sure the Handle is fitted to the vacuum body If there is a gap in front l Sl continue to push firmly until base of the handle firmly into the grooves at the top of the vacuum body Position the Hose Assembly on the back of the vacuum as shown Attach the Hose with the remaining two screws from the packet Tighten securely with a screwdriver Grasping the Quick end of the Hose Wand onto the Hose Wand Base Snap the Hose into the Hose Clip NOTE The Powerfoot will not operate effectively unless the
7. ll other side of agitator G into place RAP Turn agitator making sure belt is not pinched between agitator and agitator shield When agitator brushes are worn the agitator should be replaced To check condition of brushes disconnect cleaner from electrical outlet Move the edge of a card across bottom plate while turning agitator To maintain cleaning effectiveness replace agitator if brushes do not touch card Low suction or poor pickup may be due to a clog in the vacuum cleaner If you notice a change in the sound of the motor or a reduction in the spinning action check for clogs Empty Dirt Container Check Upper Tank for build up or clogs Grasp the Quick Reach Handle and lift Hose Wand to separate from the suction opening Check for a clog in the Base the Wand or the Hose Remove the screw attaching the Hose Wand Base to the vacuum Straighten the Hose Wand Base and unclog with long narrow object Disconnect cleaner from electrical outlet Remove bottom plate belt and agitator following directions in The belt section beginning with Fig 3 10 Discard old agitator Continue following the directions in The belt section to reposition belt new agitator and bottom plate Suction Inlet Remove the Upper Tank and check the suction inlet for a clog A WARNING To reduce the risk of injury from moving parts and or electrical shock
8. or in corners Place the vacuum on the floor with the handle in the upright position To maintain maximum cleaning performance the following maintenance steps must be performed Empty the Dirt Container when the dirt reaches the Full line on the side Check the Upper Tank and Pre Motor Filters monthly and clean or replace as needed Clean or replace the Post Motor Filter every three months Note More frequent filter cleaning may be necessary if you are vacuuming new carpet fine dust or have allergy concerns Follow the instructions on the following pages to perform these simple maintenance steps To move your cleaner from room to room put the handle in upright position tilt the cleaner back on its rear wheels and push forward Dusting Brush Tool Use to dust furniture blinds books lamps shelves draperies cushions Crevice Tool Use in tight narrow spaces Extension Wand Use with desired attachment for a longer reach NOTICE The Floor Brush will continue to rotate while you use your vacuum for above floor cleaning To prevent carpet damage do not lean on the vacuum or let the Powerfoot tilt forward NOTICE While vacuuming certain carpets and low humidity conditions may generate small static discharges The discharges are entirely harmless and are not associated in any way with the main power supply AN WARNING To reduce the risk of electric shock turn Power Switch
9. pick up dirt Possible Causes Remedies Crack or hole in Hose Check Hose and replace if needed Clog in vacuum Follow instructions on pg 10 for clearing clogs Dirt Container full Empty Dirt Container l Dirt Container or Upper Tank not installed Position correctly and lock in place properly Check and clean Upper Tank Pre Motor and Post Filters are dirty Motor Filters Vacuum cleaner is difficult to push Possible Causes Remedies Incorrect Height Adjustment Adjust Powerfoot to correct height setting Visible dirt escaping from cleaner Possible Causes Remedies l Dirt Container full Empty Dirt Container Filters missing or installed incorrectly Check Upper Tank Pre Motor and Post Motor Dirt Container installed incorrectly Filters for correct installation Pull out and re insert Dirt Container correctly If suggested solutions do not correct the problem call Esta aspiradora cumple las siguientes directivas de EMC 89 336 EEC 92 31 EEC y 93 68 EEC Directiva sobre seguridad en aparatos de bajo voltaje 73 23 EEC y 93 68 EEC If you have any comments or questions regarding Samsung products contact the SAMSUNG customer care center Customer CareCenterm WebSite _ _ 0870 SAMSUNG 726 7864 SOUTH AFRICA 0860 7267864 SAMSUNG DJ68 00148F REV 0 2
10. the plug not the cord Do not handle plug or appliance with wet hands Do not put any object into vacuum openings Do not operate with any opening blocked Keep free of dust lint hair and anything that may reduce air flow Keep hair loose clothing fingers and all parts of body away from openings and moving parts Do not use to pick up anything that is burning or smoking such as cigarettes matches or hot ashes Do not use without dust bag and filters in place Turn off all controls before unplugging Use extra care when cleaning on stairs Do not use to clean up flammable or combustible liquids such as gasoline Do not use the vacuum in areas where such liquids may be present Store your cleaner indoors in a cool dry area Do not use extension cords or plug into an electrical outlet with inadequate current carrying capacity Avoid vacuuming up sharp objects Always turn this appliance off before connecting or disconnecting the hose replacing bags or removing the bottom plate for maintenance Unplug electrical appliances before vacuuming them Save these instructions To reduce the risk of electrical shock this appliance has a polarized plug with one blade wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit in the outlet reverse the plug If it still does not fit contact a qualified electrician to replace the outlet Do not change the plug in
11. turn Power Switch OFF and disconnect plug from electrical outlet before performing troubleshooting checks Air Passageway If the clog persists follow the instructions for Checking the Rotating Floor Brush on page 9 and inspect the Air Passageway for obstructions Troubleshooting Check this list of possible problems and solutions before bringing your vacuum to a service center Vacuum cleaner won t run Possible Causes Remedies l Power cord not firmly plugged in Check electrical plug Blown fuse or breaker Check replace fuse Reset breaker Vacuum cleaner won t pick up dirt Possible Causes Remedies Incorrect Height Adjustment Adjust Powerfoot to correct height setting Hose not attached to suction opening Grasp Quick Reach Handle and firmly push Hose Crack or hole in Hose Wand onto the suction opening Check Hose and replace if needed Vacuum cleaner won t pick up dirt continued Possible Causes Remedies Broken or worn Drive Belt Replace Drive Belt see pg 9 Rotating Floor Brush bristles worn Replace brush Rotating Floor Brush jammed Remove brush and clean debris from brush ends Clog in vacuum Follow instructions on pg 10 for clearing clogs Dirt Container full Empty Dirt Container l Dirt Container or Upper Tank not installed Position correctly and lock in place properly Check and clean Upper Tank Pre Motor and Post Filters are dirty Motor Filters Tools won t
Download Pdf Manuals
Related Search