Home

CR-R885-BL : Reference and Installation Manual

1. if 1 in section 103 is selected this will override 0 to 3 in Display on Card Read see page 9 FACE LIGHT COLOUR Section 104 Default 0 The Face Light s colour can be blue or green as desired 12 Installation Manual This feature only applies when Face Light Operation programmed in Section 103 is set for Option 0 Face Light constant Enter Description 0 Blue Face Light 1 Green Face Light CHANGING THE INSTALLER CODE Section 200 Default 000000 The Installer Code is used to enter the reader s programming mode The Installer Code is six digits long where each digit can be any value from 0 to 9 PANIC ALARM A panic code can be generated and transmitted to the controller by pressing and holding the CLEAR and ENTER keys for 2 seconds 26 bit Wiegand 255 65534 37 bit Wiegand 65535 65534 This feature only applies when the communication format programmed in Section 002 is set for Option 1 26 bit Wiegand or Option 2 37 bit Wiegand RESETTING TO DEFAULT To reset the reader to factory defaults disconnect its power supply Press and hold the 1 and 2 keys simultaneously while reconnecting its power supply Proximity Reader 13 CARD PRESENTATION TEST Present the card to the reader as shown in the figure below Place the card parallel to the reader and move it toward the reader until the card code displays on the controller scree
2. x 118 5mm 2in x 19 5mm lin CE Compliant to all EU and EFTA countries except Greece according to RTT amp E directives Figure 1 Connection Drawing aoyds afgeo sapeas OY JE OM YILI OY O PIAUS Y JIOUUOI 40U OG JOffAHUOD AN Je piojys ay AEUNLLIO Adus tapea ay je paeujuua Apeaye Gum PISIUS BY YUM Eds e Geo Jepeal ey ye 40880 SAM PIONS BY JIGUUOI JOU OG SC037 Snes ajay sajqeo We aids S SI 99 4617 3924 0473UO9 SSAIIY weerga Buy indino puebaim Visual Feedback When information is entered on the reader s keypad FEEDBACK the red and or green LEDs will flash remain constant or extinguish depending on the operation Proximity Reader 5 Confirmation Beep When an operation is successfully entered the reader emits a rapid series of beep tones beep beep beep beep beep Rejection Beep When the system reverts to a previous status or an operation is incorrectly entered the reader emits one long beep tone beeeeeeeeeep PROGRAMMI NG Ensure that corresponding programming is completed in the control panel or controller connected to the reader To Program 1 Press and hold the CLEAR key for 4 seconds The reader emits a confirmation beep and the green LED illuminates 2 Enter the INSTALLER CODE Press the ENTER key default 000000 Reader emits a confirmation beep and the green LED flashes 3 Enter the 3 digit SECTION Press the
3. ENTER key Reader emits a confirmation beep and the green LED stops flashing 4 Enter the required DATA Press the ENTER key The reader emits a confirmation beep and the green LED flashes 6 Installation Manual 5 To program another section repeat steps 3 and 4 To exit programming mode press and hold the CLEAR key for 4 sec The reader emits a rejection beep and the green LED extinguishes CARD CODE OPTIONS Section 001 Default 3 The reader can also function as a keypad Enter Description 0 Keypad and reader disabled For programming only Reader only enabled A user must 1 present a valid card to the reader for Access Granted Keypad only enabled A user must enter 2 a valid code on the keypad for Access Granted Keypad and reader enabled A user 3 must present a valid card and enter a valid code for Access Granted KEYPAD COMMUNICATION FORMAT Section 002 Default 1 The reader must use the same keypad communication format as the controller Enter Description 0 8 bit Wiegand Motorola ARK 1 26 bit Wiegand also see section 006 2 37 bit Wiegand Proximity Reader 7 3 4 bits without parity 4 4 bits with parity 5 4 bits buffered without parity also see section 003 4 bits buffered with parity also see section 003 6 Note that BCD is not supported TRAN
4. PIN and Proximity Reader For Access Control Systems CR R885 BL S 6 8 0 Z o Installation and Operating Instructions V1 1 We hope this product performs to your complete satisfaction Should you have any questions or comments please visit www paradox com and send us your comments PARADOX 8 E C UR F SYSTEMS TABLE OF CONTENTS Selecting an Installation Site 2 Mounting and Wiring i 2 Mounting on Metal Surfaces 3 Technical Specifications eee ee ee 3 Feedback siii naanethedasatadanadamammvonin 5 Programmingis ios rea giro e ia 6 Card Code Options aaa 7 Keypad Communication Format 7 Transfer Limit for 4 bits Buffered Format 8 Display on Card Read 9 Keypad LOCKOUt cee ee eee ee tees eae ee eas 9 26 bit Wiegand Card Family Code Setting 10 Reader s Interface 10 Check in Supervision cence eee 11 Buzzer Setting cece cence ceca eeeeeeenaee 11 Face Light Intensity eens eee eee 12 Face Light Operation ereere rrere 12 Face Light COlOUr aes 12 Changing the Installer Code 13 Panic Alar Mesia iii AAA lai 13 Resetting to Default eens eee eee 13 Card Presentation Test eee 14 Warranty ea iii 15 P
5. SFER LIMIT FOR 4 BITS BUFFERED FORMAT Section 003 Default 00 This feature sets the number of digits retained in memory before the data is sent to the controller For example if section 003 is set at 05 the reader will transmit once five digits are entered on the keypad This feature only applies when the format programmed in Section 002 is set for Option 5 4 bits buffered without parity or Option 6 4 bits buffered with parity Enter Description If section 002 is Option 5 4 bits buffered without parity If section 002 is Option 6 4 bits buffered with parity 01 to 11 01 to 10 8 Installation Manual DISPLAY ON CARD READ Section 004 Default 3 The response from a card being presented to the reader can be adjusted according to the installation s requirements Enter Description 0 Display on Card Read disabled 1 Red Status LED flashes 2 Green Status LED flashes 3 Red and green Status LEDs flash 4 Face Light flashes 5 Face Light and red Status LED flash 6 Face Light and green Status LED flash 7 Face Light and both Status LEDs flash Select 0 in Face Light Operation see page 12 to enable options 0 to 3 in section 004 or select 1 in Face Light Operation see page 12 to enable options 4 to 7 in section 004 If section 103 page 12 is set to 1 the face light
6. e the cable to the controller and connect as shown in Figure 1 Connection Drawing on page 5 MOUNTING ON METAL SURFACES Although the read range may slightly decrease the reader can be mounted on metal However do not box in or surround the card reader with any kind of metal If the reader must be installed in a metal enclosure ensure that the face of the card reader is not covered and that at least 1 6 4cm remain between the card reader and the metal on all sides of the card reader TECHNICAL SPECI FI CATIONS Input Voltage Typical 13 8Vdc min 11 0Vdc max 14 5Vdc Input Current Typical 65mA 12 5Vdc with card 105mA Consumption Typical 812mW 12 5Vdc with card 1 31MW Frequency Exciter Field 125KHz Pulse Modulated receive low 12 500KHz Receive high 15 625KHz Operating Temp 25 C 13 F to 65 C 149 F Output formats Reader 26 and 37 bit Wiegand Keypad 8 26 and 37 bit Wiegand 4 bit with or without parity and 4 bits buffered with or without parity Cable Distance 152 4m 500ft Proximity Reader 3 Suggested Cables Indicators Weight Material Dimensions Approvals 4 Installation Manual 22AWG 0 8mm Multi conductor Alpha 5196 5198 18AWG 1 2mm Multi conductor Alpha 5386 5388 Belden 9553 18AWG 6 conductor stranded w overall shield Beeper red LED green LED blue or green Face Light 280g 9 8 oz Black UV resistant ABS plastic 99 5mm 5 75in
7. n At this point the card is read decoded data transmitted to the controller and the controller has responded accordingly To read the card again remove and re insert the card into the reader s field 14 Installation Manual WARRANTY For complete warranty information on this product please refer to the Limited Warranty Statement found on the website www paradox com terms Your use of the Paradox product signifies your acceptance of all warranty terms and conditions 2003 2007 Paradox Security Systems Ltd All rights reserved Specifications may change without prior notice One or more of the following US patents may apply 7046142 6215399 6111256 6104319 5920259 5886632 5721542 5287111 5119069 5077549 and RE39406 and other pending patents may apply Canadian and international patents may also apply The PIN and Proximity Reader is a trademark or registered trademark of Paradox Security Systems Ltd or its affiliates in Canada the United States and or other countries Proximity Reader 15 Notes 16 Installation Manual For technical support in Canada or the U S call 1 800 791 1919 Monday to Friday from 8 00 a m to 8 00 p m EST For technical support outside Canada and the U S call 00 1 450 491 7444 Monday to Friday from 8 00 a m to 8 00 p m EST Please feel free to visit our website at www paradox com PAR AD OX 8 EC UR rer SYSTEMS paradox com Printed in Canada 11 2007 PPIN E102
8. ption 2 37 bit Wiegand When no actions are performed on the reader for a period of time it will communicate its status to the controller every 30 seconds by sending a code to confirm its presence 26 bit Wiegand 255 65535 37 bit Wiegand 65535 65535 If the reader does not communicate its status every 30 seconds the controller can be programmed to generate an alarm Enter Description 0 Check in Supervision disabled 1 Check in Supervision enabled BUZZER SETTI NG Section 101 Default 3 The number of beep tones emitted as a response to a card being presented to the reader can be adjusted from 0 disabled to 7 7 rapid beep tones Enter Description Number of beep tones per response 0 to 7 Proximity Reader 11 FACE LIGHT INTENSITY Section 102 Default 4 The Face Light s illumination can be adjusted according to the installation s requirements from 0 extinguished to 8 brightest Enter Description 0 to 8 Face Light s intensity level FACE LIGHT OPERATION Section 103 Default 0 The Face Light can be set to remain illuminated continually or can follow the Status LEDs state Enter Description O Face Light constant 1 Face Light follows Status LEDs If O in section 103 is selected this will override options 4 to 7 in Display on Card Read see page 9 In addition
9. roximity Reader 1 INSTALLATION For the reader to function correctly with the access control system some programming may be required in the controller or control panel of the host system For further instructions refer to the appropriate manual Only explanations directly concerning the reader s programming will be included in this manual SELECTING AN INSTALLATION SITE e Avoid wiring the reader s cables in the same conduit as AC power cables lock power or signal wiring e Reader wiring must remain a minimum of 30cm 12in away from other wiring such as wiring for AC power computer data telephones electric locks etc e Avoid sites within 1 1m 3 5ft of computer monitors or CRTs e Avoid sites near sources of broad spectrum EMI noise such as motors pumps generators DC to AC converters AC switching relays power supplies and light dimmers e Avoid sites near potential sources of RF signals such as cellular phones two way radios etc MOUNTING AND WI RI NG After selecting a site for the reader use the mounting plate as a guide to drill two holes to secure the mounting plate and a hole for the cable 0 95cm to 2 54cm 0 375in to lin wide Place a grommet around the edge of the hole for the cable Prepare the reader s cable by cutting the cable 2 Installation Manual jacket back 3 175cm 1 25in and stripping the wires back 0 635cm 0 25in Splice the reader s wires with a recommended cable wire Rout
10. will also flash KEYPAD LOCKOUT Section 005 Default 0 The reader s keypad comes with a feature that will lock the keypad for 60 seconds when an installer code is entered incorrectly 3 consecutive times Proximity Reader 9 Enter Description 0 Keypad Lockout disabled 1 Keypad Lockout enabled 26 BIT WIEGAND CARD FAMILY CODE SETTI NG Section 006 Default 000 When the keypad is enabled the card s family code must be programmed in order for the keypad to recognize the user s PIN When a user enters a PIN on the keypad the reader will automatically add the family code programmed in section 006 to the beginning of the PIN before transmitting the data to the controller Therefore also ensure that all cards to be used with the reader contain the same family code This feature only applies when the communication format programmed in Section 002 is set for Option 1 26 bit Wiegand Enter Description 0 to 255 Cards Family Code READER S INTERFACE Section 007 Default 0 The reader must be programmed to use the same communication format as the controller Enter Description 0 26 bit Wiegand 1 37 bit Wiegand 10 Installation Manual CHECK IN SUPERVISION Section 008 Default 0 This feature only applies when the communication format programmed in Section 002 is set for Option 1 26 bit Wiegand or O

CR-R885-BL : Reference and Installation Manual

Contents

Download Pdf Manuals

Related Search

Related Contents