User's Manual - Ultra Factor SRL
Contents
1. EZ 2000 6000 Users Manual Rev D 22 5 Feed the ribbon from the Ribbon Supply Shaft under the print head Wrap the ribbon around the Ribbon Rewind Shaft and stick it onto the empty ribbon roll Note DO NOT feed the ribbon under the Moveable Sensor EZ 2000 6000 Users Manual Rev D 23 2 3 PC Connection 1 Please make sure the printer is powered off 2 Take the power cable plug the cable switch to the power socket and then connect the other end of the cable to the printer power socket 3 Connect the cable to the USB parallel port on both side of printer and PC 4 Power on the printer the LCD display would show the printer model and F W version EZ 2000 6000 Users Manual Rev D 24 2 4 Driver Installation 1 Once the USB cable is connected from PC to the printer PC will automatically detect the new device and begin the installation process Welcome to the Found New Hardware Wizard Tha miran kepa eu stall a eve ver fora hades deve Freie Sew Hahei d gt USE Devce Int adr T ek ckck Maxi Insert the product CD mmm select Specify a Locate Driver Files 3 location and describe Where do you want Windows to search for driver files the path of the printer driver Search for driver tiles for the following hardware device Follow the instruction2. gt Self test 3 beeps Press and hold key and turn on the za E poveron mm printer until the buzzer beeps 3 times med gt 3 beeps gt After entering Self test Mode keep holding SOR peop gt key until the buzzer beep once i Press and hold key and turn on the gt i 2 beeps Press and hold gt amp keys and turn Go to default en twice on the printer until the buzzer beeps 2 times The printer setting will go to default Download Press and hold L key and turn on the mode L Power on 1 beep printer until the buzzer beeps once This mode is only for firmware downloading When Power on press and hold key Setting mode 3 beeps about 3 to 4 seconds until the buzzer beep 3 times EZ 2000 6000 Users Manual Rev D 37 With LCD monitor Item Key Beep LCD Message Description gt Press and hold key and turn Self test Power 3 beeps Self test on the printer until the buzzer ue beeps 3 times After entering Self test Mode Now in Dump Mode keep holding key until the buzzer beep once Press and hold key and turn Auto Il Power Auto sensing sensing o 3 beeps Mode on the printer until the buzzer beeps 3 times n gt Press and hold gt amp keys Go to Een gt PEEPS Goto default and turn on the printer until the default Power on twice buzzer beeps 2 times The printer setting will go to default Press and hold key and Download m Power 1 beep DL MODE turn on the printer unt
3. Check the power cable power on the printer LED light indicates error messages after Check for software setting or program printing stops command errors Replace with suitable label or ribbon Check if label or ribbon is all out Check if label is jammed tangled up Check if mechanism is closed Thermal Print Head not positioned correctly Check if sensor is blocked by paper label Check for abnormal cutter function or of no actions if cutter is installed Printing started but nothing was printed Check if label is placed upside down or if on the label label is not suitable for the application Select the correct printer driver Select the correct label and print type When printing label is jammed tangled Clean the label jam and if label is stuck on up Thermal Print Head please remove it by using soft cloth with alcohol When printing only part of the contents Check if label or ribbon is stuck on the were printed Thermal Print Head Check if application software has errors Check if start position setting has errors Check if ribbon has wrinkles Check if ribbon supply shaft is creating friction with the platen roller If the platen roller needs to be replaced please contact your reseller for more information Check if power supply is correct When printing part of the label wasnt Check if Thermal Print Head is stained or printed completely dusted Use internal command T to check Thermal Print Head can
4. 200 1 EN 55024 1998 A1 2001 A2 2003 EC 61000 4 2 1995 A1 1998 A2 2000 LEC 61000 4 3 2002 A1 2002 TEC 61000 43 4 1995 A1 2000 A2 2001 TEC 61000 4 5 1995 A 1 2000 EC 61000 4 6 1996 A1 2000 TEC 61000 4 11 1994 A4 1 2000 Meesurement Facilities Laboratory Name Compliance Certification Scrvices inc Tainan Lab Na 8 Jiu Cheng Ling Jiaokeng Village Sinhua Township Tainan Hsien 712 Taiwan R O C Tel 336 6 5902201 Fax 886 6 5802202 tits device has been shown te Pe in compliance wir and M tt ferted in accordance with the measurement procedures specified in the Standards Specifications listed above saved as tudicated tn the measurement report number 61030405 E Ej Fe Pr lt e P d ef CCL e Alex Chiu Manager Daie November 07 2006 EZ 2000 6000 Users Manual Rev D 6 VERIFICATION OF COMPLIANCE This Verification of Compliance is ebe issued to the below named company The e rest results of this report relate only to the tested sample identified in this report Technical Standard FCC 47 CFR PART 15 SUBPART B AND ANSI C63 4 2003 IC ICES 003 General Information Applicant GODEX INTERNATIONAL CO LTD 4F No 168 Liancheng Rd Jhonghe City Taipei County 235 Taiwan R O C Manufacturer GODEX INTERNATIONAL CO LTD 4F No 168 Liancheng Rd Jhonghe City Taipei County 235 Taiwan R O C Product Description EUT Description Thermal Transfer Printer Model Number EZ 6xxxPy
5. on both knobs of Ribbon Rewind Shaft and Ribbon Supply Shaft 1 represents the strongest tension and 4 is the weakest tension When the tension is too weak to pull the ribbon please decrease the tension of Ribbon Supply Shaft or increase the tension of Ribbon Rewind Shaft To adjust the ribbon shaft knob please push the knob inward and then start to turn If the ribbon wrinkles occurs during printing due to the differences of ribbon materials please increase the tension by turning Ribbon Rewind Shaft Knob clockwise For more detail about the ribbon wrinkle problem please refer to Chapter5 6 If a narrower ribbon is used especially when ribbon width is less than 2 the printer might have problem to pull the labels In this case please decrease the tension by turning Ribbon Supply Shaft Knob counterclockwise Moreover the Ribbon Roll maybe difficult to be removed because of the shape change that result from over power tension In this case please decrease both tensions of Ribbon Supply Shaft and Ribbon Rewind Shaft by turning Knobs counterclockwise EZ 2000 6000 User s Manual Rev D 50 5 4 Thermal Print Head Cleaning Unclear printouts some parts of label cannot be printed may be caused by dusty print head ribbon stain or label liner glue Therefore when printing it s necessary to keep the top cover closed Also check and prevent paper label from being stained or dusty to ensure print quality and t
6. oy USE Device on the Window and complete the driver The wizard searches for suitable drivers in its driver database on your computer and in i any of the following optional search locations that you specify installation To start the search click Next IF you are searching on a floppy disk or CD ROM drive insert the floppy disk or CD before clicking Next Optional search locations Floppy disk drives CD ROM drives je Specify a location a a rasen E O Microsoft Windows Update lt Back Cancel Found New Hardware Wizard l x Insert the manufacturer s installation disk into the drive IK selected and then click OR Cancel Copy manufacturer s files from Eis senes nstal Godex 2Zond4 w EZ 2000 6000 Users Manual Rev D 25 3 Accessory 3 1 Internal Rewinder for EZ 2000 Plus Note Peel off liner Max width 118mm Suggestion Liner thickness 0 06mm 0 25mm 1 Place the printer onto a smooth surface open the top cover and face the printer sideways Note Before the installation please power off the printer first 2 Turn the printer sideways and remove the Rewinder module cover plate EZ 2000 6000 Users Manual Rev D 26 Take off the U Shape Clip from the Liner Rewind Shaft Secure the Rewinder unit onto the printer After the Rewinder is installed plug the Rewinder Cable Connector onto the Rewinder Connector Rewinder I
7. 0 Q100 3 Option DO 700 AD Gap Sensor AD 129 162 Code Page 850 Keyboard Layout US International 195 3 4 5 Dump Mode When label setting and the print result don t match it s recommended to go into the Dump Mode to check whether there s a mistake in data transmission between the printer and the PC For example when printer receives 8 commands yet without processing these commands only printed out the contents of the commands this will confirm whether the commands were received correctly Test procedures to enter the Dump Mode are as follows 1 Power off the printer press and hold the FEED key 2 Power on the printer while still holding the FEED key 3 When LCD Display shows DUMP MODE BEGIN release the FEED key Printer will automatically print DUMP MODE BEGIN This means the printer is already in Dump Mode 4 Send commands to the printer and check to see if the print result matches the commands sent To cancel get out of the Dump Mode press the FEED key this time printer will automatically print out OUT OF DUMP MODE This indicates that printer is back in the standby mode Or power off to exit the Dump Mode 4 6 Auto Sensing Printer can automatically detect label black mark paper length and record it By this way without setting the print length the printer can accurately detect the label black mark positions 1 Check if the Moveable Sensor Mark is located at the right sen
8. 2 3rd Edition 1997 Class A ANSI C63 4 2001 CNS 13438 IEC60950 1 2001 GB4943 2001 GB9254 1998 GB17625 1 2003 EN60950 1 2001 CAUTION Danger of explosion if battery is incorrectly replaced Replace only with the equivalent type recommended by the manufacture Dispose of used batteries according to the manufacturer s instructions Specifications are subject to change without notice EZ 2000 6000 Users Manual Rev D 1 Safety Instructions Bitte die Sicherheitshinweise sorgf ltig lesen und f r sp ter aufheben 1 Die Gerate nicht der Feuchtigkeit aussetzen Bevor Sie die Gerate ans Stromnetz anschlieBen vergewissern Sie Sich dass die Spannung des Gerats mit der Netzspannung Ubereinstimmt Nehmen Sie das Ger t bei berspannungen Gewitter vom Netz Das Ger t k nnte sonst Schaden nehmen Sollte versehentlich Fl ssigkeit in das Ger t gelangen so ziehen sofort den Netzstecker Anderenfalls besteht die Gefahr eines lebensgef hrlichen elektrischen Schlags Wartungs und Reparaturarbeiten d rfen aus Sicherheitsgr nden nur von autorisierten Personen durchgef hrt werden Bei Wartungs und Reparaturarbeiten m ssen die Sicherheitsvorschriften der zust ndigen Berufsverb nde und Beh rden unbedingt eingehalten werden Bei Verletzungen unbedingt den Arzt aufsuchen und die gegebenenfalls die zust ndigen Stellen benachrichtigen Unterlassung kann zum Verlust der Versicherungsleistunge
9. 5200 Xon Xoff DSR DTR USB port V2 0 CF card socket Back lit LCD Display 128x64dots Graphic LCD Control Panel Three single color LED lamps Power Ribbon Media Three control keys FEED PAUSE CANCEL Power Operation 41 F to 104 F 5 C to 40 C Environment Operalc 4 F to 122 F 20 C to 50 C Humidity SCT 30 85 non condensing Free air Storage 10 90 non condensing Free air Length 516mm 20 31 Height 285 mm 11 22 Width 345 mm 13 58 Weight 16 7 Kg Cutter Stripper sensor with internal re winder Ethernet Adapter Parallel amp PS2 Adapter Applicator Interface digit in 1 digit out 3 5V 1 500mA Specifications are subject to change without notice Printer Dimension EZ 2000 6000 Users Manual Rev D 12 1 3 Communication Interface Parallel Interface Handshake DSTB connects to the printer BUSY connects to the host Interface cable Parallel cable compatible to IBM PC Pin out See below Strobe host printer Data 0 7 host Acknowledge printer Busy printer Paper empty printer Select printer Auto Linefeed host printer N C Signal Gnd Chasis Gnd 5V max 500mA Signal Gnd host Initialize host printer Error printer Signal Ground N C Select in host printer Serial Interface Serial Default 9600 baud rate no parity 8 data bits 1 stop biti XON XOFF protocol and Setting RTS CTS RS232 HOUSING 9 pin to 9 pin DB9SOCK
10. Number EZ 2XXXPyvy x 0 9 y 0 9 a 7 Brand Name GODEX THARO ACCUMAX SYSTEM WAVE Measurement Standard EN 55022 1998 A1 200G A2 2003 EN 61000 3 2 2000 EN 61000 3 3 1995 A1 2001 EN 55024 1998 A1 2001 A2 2003 IEC 61000 4 2 1995 A1 1998 A2 2000 TEC 61000 4 3 2002 A1 2002 TEC 61000 4 4 1995 rA1 2000 A2 2001 IEC 61000 4 5 19951A1 2000 TEC 61000 4 6 1996 A4 1 2000 TEC 61000 4 11 1994 A1 2000 Measurement Facilities Laboratory Name Compliance Certification Services Inc Tainan Lab Na 8 Jiu Cheng Ling Jiaokeng Village Sinhua Township Tainan Hsien 712 Taiwan AN OC Tel 8 6 6 3S802201 Fax 886 6 5802202 This device has been shown to be in compliance with and was tested in accordance with the measurement procedures specified tu the Standards amp Specifications listed above and as indicated in the measurement report number 61030404 E EZ 2000 6000 Users Manual Rev D 4 VERIFICATION OF COMPLIANCE This Verification of Compliance is hereby issued to the below named company The test results of this report relate only to the tested sample identified in this report Technical Standard FCC 47 CFR PART 15 SUBPART B AND ANSI C63 4 2003 IC ICES 003 General Information Applicant GODEX INTERNATIONAL CO LTD 4F No 168 Liancheng Rd Jhonghe City Taipei County 235 Taiwan R O C Manufacturer GODEX INTERNATIONAL CO LTD 4F No 168 Liancheng Rd Jhonghe City Taipei County 235 Taiwan R O C Product D
11. PH Spring Box pressure use a flat tip screwdriver to turn the screw clockwise to increase the pressure counterclockwise to decrease the pressure EZ 2000 6000 User s Manual Rev D 52 5 6 Ribbon Shield Adjustment 1 Due to the differences in the ribbon materials if ribbon wrinkles occur during printing please adjust the ribbon shield screw Example If ribbon wrinkles occur as a please turn the ribbon shield screw A clockwise and if ribbon wrinkles occur as b please turn the ribbon shield screw B clockwise ENDEL TEST LABEL EI Ill N 123456789 COMPANY NAME SAM PLE SAMPLE mi all NN 1234567890 1234567890 a b It is recommended to adjust by a half of a circle each time to fully control the printing quality and status Perform the printing test after adjustment and if a ribbon wrinkle has not been removed please perform the adjustment one more time Each adjustment on the screw can not be turned more than two circles Note If the screws are turned more than acceptable range then paper feed may not be smooth In this circumstance please restore the ribbon shield screws and do the adjustment again EZ 2000 6000 User s Manual Rev D 53 5 7 Adjust the Cutter The cutter adjusting hole is on both sides of cutter The cutter will not work properly if there is a paper jam Please power off the printer and use a 3mm hexagon screwdriver to insert into the hole Turn the screwdrive
12. Page852 Default US German Spanish Italian Finnish Dutch Belgian Default Recall Label Recall Label Recall label from memory card Keyboard Setup Setting the keyboard Keyboard Mode Code page Setup Setting the code page Printing Option Set the print quantity Clock Setup Set the clock and clock display Exit KB Modell Exit PS2 KB Mode Default ON Buzzer Setup ON OFF EZ 2000 6000 Users Manual Rev D 41 Keyboard Setup Default ON Smart Backfeed ON This function must install stripper or cutter OFF Default OFF ON When password protect enable the password is reguired for entering Setting Mode OFF Default ON Top of Form ON Start each printing from the Top of Form position OFF Go to default Set the IP address of Ethernet module to factory default setting Preview Note 1 Default Setting is the original settings from the factory if other changes are made on the settings then follow the new settings Password Note 2 Printer will store the previous settings after power off thus if settings are to be changed again please enter the Setting Mode to reset EZ 2000 6000 Users Manual Rev D 42 The diagram of Setting Mode Darkness 0 19 Stop Position Printhead Position Print Mode Option Setup COM P
13. T DBOPLVG 5V max 500mA O ONO G R 0 N NE E AT PRINTER PC Note The total current output from parallel port and serial port altogether can not exceed 500mA EZ 2000 6000 Users Manual Rev D 13 USB Interface Connector Type Internal Interface Ne h TXD 2 2 RXD RXD 3 3 TXD CTS 14 4 RTS GND 5 5 GND RTS 6 6 CTS 7 8 CTS 9 10 11 GND W e 12 N C 1 1 N C SCC RO a s CTS 4 4 RTS ao lt ZZ Ais pC N C 7 7 N C Rs b CTS i 9 9 10 10 11 11 12 12 EZ 2000 6000 Users Manual Rev D 14 Applicator wafer Applicator module 1 5V O o w Printing out 3 Printing 4 Print error Printed out Printed Print in Print 8 9 10 EZ 2000 6000 Users Manual Rev D 15 1 4 Printer Parts Appearance 6 Power Socket The communication ports may vary depending on product types EZ 2000 6000 Users Manual Rev D 16 Internal 12 11 1 o 10 3 4 5 9 6 8 7 Ribbon Rewind Shaft i Ribbon Supply Shaft Printer Mechanism 6 PrintHed Lee ooo 8 Label Guide 9 Label Tension Plate Movable sensor EZ 2000 6000 Users Manual Rev D 17 Control Panel 1 2 3 B OWER RIBBON Pp FEED PAUSE J CANCEL MEDIA LED RIBBON LED POWER LED LCD Product type dependent CANCEL Key 6 PAUSE Key FEED Key 8 MINUS Key In setting mode 9 MENU Key In setting mode PLUS K
14. USTMENT 2 222 220 20022002000n0n nun 48 5 1 Print Head Module Installation Removal Instruction nennen 48 Se PEL Print LIne AG USTI EN ze seen 49 5 3 Ribbon Tension Adjustment nena 50 5 4 Thermal Print Head Cleaning EE 51 5 5 Print Head Balance and Pressure Adjustment eee eeeeeeeeeaeeeeeeeeaeeeeeeeaaaees 52 5 6 Ribbon Shield Adjustment ses ennerien rearea naana D3 D527 HAUSE ING OUIET eege ee nee 54 9 8 GF Gard lnsirUelon sa nina es ooo o 54 5 9 TTOUDlESNOOUN e WEE 55 EZ 2000 6000 Users Manual Rev D 9 1 Barcode Printer 1 1 Printer Accessories After unpacking please check the accessories that come with the package and store appropriately Barcode printer Power cable USB Cable Label Roll Sample Ribbon Empty Ribbon Roll Auick Start Guide CD includes label editing software QLabel Manual 20000000 EZ 2000 Plus EZ 6000 Plus _ 1 2 General Specifications Model EZ 2100 Plus EZ 2200 Plus Resolution 1203 dpi 8 dot mm Print Mode Thermal Transfer Direct Thermal CPU 32Bit Memory WMD Flash 16MB SDRAM Print Speed 2 IPS 6 IPS 2IPS 7IPS 2 IPS 6 IPS Min 13mm 0 51 Min 13mm 0 51 Print Length wa 4572mm 180 Max 2159mm 85 Print Width 104 mm 4 09 Z 2300 Plus Sensor Type Adjustable transmissive sensor and reflective sensor left aligned Type Label gap and black mark sensing SEMI VAN Detection Label length auto sensing or pro
15. User s Manual EZ 2000 Plus EZ6000 Plus P N 920 011911 00 7 FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This eguipment has been tested and found to comply with the limits for a CLASS A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at own expense EMS AND EMI COMPLIANCE STATEMENT FOR EUROPEAN USERS This equipment has been tested and passed with the requirements relating to electromagnetic compatibility based on the standards EN 55022 1998 A1 2000 A2 2003 CISPR 22 Class A EN 55024 1998 A1 2001 A2 2003 IEC 61000 4 Series EN 61000 3 2 2000 amp EN 61000 3 3 1995 The equipment also tested and passed in accordance with the European Standard EN55022 for the both Radiated and Conducted emissions limits EZ PLUS SERIES TO WHICH THIS DECLARATION RELATES IS INCONFORMITY WITH THE FOLLOWING STANDARDS EN55022 1998 CLSPR 22 Class A EN55024 1998IEC 61000 4 Serial EN61000 3 2 2000 EN 6100 3 3 1995 CFR 47 Part 15 CISPR 2
16. and then blinks for each pressing The Speed buzzer will beep when the adjustment reaches the maximum or minimal Direct Thermal Thermal Ribbon light blinks Transfer Ribbon light blinks and Media light flashes The Media light blinks for each pressing and the buzzer will beep when the adjustment reaches the maximum or minimal EZ 2000 6000 Users Manual Rev D 39 With LCD monitor Press and hold key about 3 to 4 seconds until the buzzer beep 3 times and LCD shows Setting mode The LCD monitor will show different options on the bottom LCD Language English Enter Mext Exit After entering to Setting mode the first highlight on LCD monitor indicates the current item for setting LCD Language In setting type the first line indicates the English current item and the second line indicates current setting Enter g In adjustment type the first line indicates the current item and the second line indicates current value Plus press key to increase the value Minus press key to decrease the value Next press key to go to next item Below are general descriptions of setting items Default 15 Set the darkness of printing result The setting value is from 0 to 19 and the default value is Default 12 Stop Position Set the stop position of printing The setting value is from 0 to 60 Default 0 Printhead Position Set the pos
17. er onto a smooth surface and open the top cover Unscrew two screws as indicated in figure and remove the left top cover from the printer Unscrew the screws of parallel port cover and remove the cover EZ 2000 6000 User s Manual Rev D 34 Align the Parallel PS2 module to the parallel port and secure the module onto the back plate Connect one end of the 30 pin connector cable to the main board and the other end to the Parallel PS2 module 6 The Parallel PS2 module installation is complete EZ 2000 6000 User s Manual Rev D 35 4 Control Panel 4 1 Control Panel Introduction Without LCD monitor Control keys FEED PAUSE LED indicators Power Power on After turning on the power the Ribbon and Media lights Ready Power will flash alternately until the completion of initialization Ribbon Ribbon status indication Media status indication With LCD monitor Control keys gt FEED I PAUSE LED indicators Power Power on After turning on the power the Ribbon and Media lights will flash alternately until the completion of initialization Ribbon status indication Meda Media status indication Ready Power EZ 2000 6000 Users Manual Rev D 36 4 2 Control Keys Introduction gt FEED Key After pressing the FEED key printer will send the media according to media type to the specified stop position When printing with continuous media pressin
18. escription EUT Description Thermal Transfer Printer Model Number EZ 2xxxPyyy x 0 9 y 0 9 a z Brand Name GODEX THARO ACCUMAX SYSTEM WAVE Laboratory Name Compliance Certification Services Inc Tainan Lab No 8 Jiu Cheng Ling Jiaokeng Village Sinhua Township Tainan Hsien 712 Taiwan R O C Tel 886 6 580220 Fax 836 6 5802202 This device has been shown to be in compliance with and was tested in accordance with the measurement procedures specified in the Standards amp Specificarions listed above and as indicated ir the measurement report number 61030404 D JET RER e Alex Chiu Manager Date November 07 2006 EZ 2000 6000 Users Manual Rev D 5 CE VERIFICATION OF COMPLIANCE This Verification of Compliance is hereby issued to the below named company The test pas o fll ga only e tested sample identified in be Technical Standard EMC DIRECTIVE 89 336 EEC EN 55022 EN 55024 General Information Applicant GODEX INTERNATIONAL CO LTD 4F No 168 Liancheng Rd Jhonghe City Taipei County 235 Taiwan R O C Manufacturer GODEX INTERNATIONAL CO LTD 4F No 168 Liancheng Rd Jhonghe City Taipei County 235 Taiwan ROC Product Description EUT Description Thermal Transfer Printer Model Number EZ 6xxxPyyy x 0 9 y 0 9 a z Brand Name GODEX THARO ACCUMAX SYSTEM WAVE Measurement Standard EN 55022 1998 A1 2000 A2 2003 EN 61000 3 2 2000 EN 61000 3 3 1995 A1
19. ever out and flip it upward to the right Remove the U Shape Clip 6 Install the media into the printer Note Label liner thickness is recommended to be 0 06mm 10 with basic weight 659 6 7 Suggestion When using the stripper module set the stop position to 12 in QLabel and the E value is 12 Peel off a few labels from the liner about 400mm of liner and then feed the liner through the Printer Mechanism and around the Label Feed Guide EZ 2000 6000 User s Manual Rev D 30 Wrap the liner around the Liner Rewinder Shaft and use the U Shape Clip to secure the liner Flip the print head lever downward and then push it back to the original position Note Make sure the liner rewind is in correct direction 10 Screw the bottom front cover back onto the printer Press lower part of the stripper sensor to flip it open Flip the stripper sensor to the sensor detecis position Close the top cover to complete stripper installation EZ 2000 6000 Users Manual Rev D 31 3 4 Cutter Installation 1 Cutter Cover EZ 2000 Plus 2 Cutter Cover EZ 6000 Plus 3 Cutter 4 Locks 5 Screws x 2pcs Note1 Do not cut self adhesive labels The traces of adhesive will pollute the rotary knife and impair safe operation Note2 The service life of EZ 2000 Cutter is 500 000 cuts with paper weights 1609 and 250 000 cut
20. ey In setting mode EZ 2000 6000 User s Manual Rev D 18 2 Printer Installation This printer model has the following print modes Thermal Transfer When printing ribbon must be installed to transfer the print contents onto the TT media Direct Thermal When printing no ribbon is necessary it only requires direct thermal media DT Please check the specific print mode and then go into the Setting Mode after power on the printer 2 1 Label Installation Place the printer on a horizontal surface and open the top cover Follow the seguence and direction as the figure shows pull the Print Head Lever out and flip it upward to the right Pull the Label Alignment Guide to the direction as the blue arrow 1 indicates Flip the Label Supply Guide upward as the blue arrow 2 indicates EZ 2000 6000 Users Manual Rev D 19 Place the label roll onto the Label Roll Bar and align the label to printer s inner wall To avoid the damage of media please do not sgueeze label roll too hard Pull the Label Alignment Guide back and make it fit the edge of label roll Note Please always hold the bottom of the Label Alignment Guide when moving Follow the direction as the figure shows to feed the label Put the label under the Moveable Sensor and stretch it to the Tear Off Bar Note Moveable Sensor should be aligned to the position of label gap black mark and punch hole You can adju
21. g the FEED key will feed media out to a certain length When printing labels pressing the FEED key will feed one label at a time if the label is not sent out in a correct position please proceed with the Auto Sensing see page45 Pause Key When pressing the Pause key in standby mode the printer will go into the Pause Mode and LCD Display will indicate EZ xxxx Vx xxx Pause At this status printer wont be able to receive any command Then pressing the Pause key once again the printer will get out of the Pause mode and go back to standby mode Pressing the Pause key while printing printer will pause the print job When the Pause key is pressed one more time the printer will continue with the rest of the print job For example if the print job contains 10 labels press the Pause key to stop printing after 2 labels are printed When pressing the Pause key again printer will finish the printing of the remaining 8 labels LJ Cancel Key Pressing the Cancel key while printing the LCD Display will show Print job is cancelled it means the printer cancels the current print job For example if the print job contains 10 labels press the Cancel key after 2 labels are printed the remaining 8 labels won t be printed and the printer goes back to standby mode With different combinations of FEED PAUSE and CANCEL keys the printer can perform various functions as follows Without LCD monitor kem Key Beep Description
22. gram command setting Length 450 m 1471 ft Type transfer ribbons wax hybrid and resin in widths of 30 to 110 mm 1 18 to 4 33 Auto ink inside and ink outside Core inner diameter 25 4 mm 1 Max Ribbon roll diameter 76 mm 2 99 Printer Language EZPL Firmware downloadable Application QLabel IV EZPL only DLL amp Driver Microsoft Windows NT 4 0 2000 and XP Ribbon Label Roll Max 203mm 8 0 with 76 2mm 3 ID core Core Diameter 38 1mm 1 5 gt 76 2mm 3 Width Tear 25 4mm 1 gt 118 0mm 4 64 Width Cutter Max 117mm 4 61 Width Stripper Rewind 25 4mm 1 118 0mm 4 64 Thickness 0 06 0 25mm EZ 2000 6000 Users Manual Rev D 10 11 resident alphanumeric fonts included OCR A 8 B those are expandable 8 Resident Fonts times horizontally and vertically All bit mapped fonts in 8 orientations Scalable Font Code Page 850 8 852 in 4 orientations Windows bit mapped in 8 orientations True Type font Ver 2 XX and Asian Bois BON oag fonts in 4 orientations Image Handling BMP PCX Support ICO WMF JPG EMF file through software Code 39 Code 93 Code 128 subset A B C UCC EAN 128 K Mart UCC EAN 128 UPC A E add on 2 amp 5 2 of 5 2 of 5 with Shipping Bearer Barcodes Bars EAN 8 13 add on 2 8 5 Codabar Post NET EAN 128 DUN 14 MaxiCode HIBC Plessey Random Weight Telepen FIM China Postal Code RPS 128 PDF417 Datamatr
23. il the mode on VX XX buzzer beeps once This mode is only for firmware downloading a When Power on press and hold en 3 beeps Setting mode key about 3 to 4 seconds until the buzzer beep 3 times EZ 2000 6000 Users Manual Rev D 38 4 3 Setting mode In the Setting Mode changes can be made according to reguirement on the printing mode options media type and parallel interface printer can only go into setting when connected to PC by parallel cable USB cable or serial cable 1 Power on the printer and make sure it is on Ready to print status 2 Press and hold Pause key about 3 to 4 seconds until the buzzer beep 3 times for product types that with LCD monitor the LCD will display Setting Mode 3 In the Setting Mode the keys have the following functions MINUS Enter MENU NEXT F PLUS Exit 4 Before exiting the Setting Mode printer will prompt user whether to save the settings After user s response on whether do or do not save the settings printer will return to standby mode Without LCD monitor Press and hold key about 3 to 4 seconds until the buzzer beep 3 times Blinking Steady l Ribbon Media Description Exit i men i i Ribbon amp Media lights flash without i simultaneously saving Ribbon light flashes and then blinks for each pressing The Darkness buzzer will beep when the adjustment reaches the maximum or minimal Media light flashes
24. ith the 1 sign is default setting 43 EZ 2000 6000 Users Manual Rev D 4 4 Self Test The Self Test function will help user to check whether the printer is operating normally In Self Test Mode the printer will print out a test sample each time when the FEED key is pressed To break off the Self Test procedure please power off the printer Below are the Self Test procedures 1 Power off the printer press and hold the FEED key 2 Power on the printer while still holding the FEED key release the FEED key after hearing 3 beeps 3 After about 1 second printer would automatically print out the following and the LCD Display would show Self Test Model amp Version Serial port setup Test pattern Number of DRAM installed Image buffer size Number of forms Number of graphics Number of fonts Number of Asian fonts Number of Databases Free memory size Speed Density Ref Point Print direction Label width Form length Cutter Stripper Mode Gap sensor AD Code Page Keyboard Layout Self Test includes the internal printer data setting This means the printer is operating normally EZ 2000 6000 Users Manual Rev D 44 EZXXXX VX XXX Serial port 96 N 8 1 1 DRAM installed Image buffer size 2200K 000 FORM S IN MEMORY 000 GRAPHIC S IN MEMORY 000 FONT S IN MEMORY 000 ASIAN FONT S IN MEMORY 000 DATABASE S IN MEMORY 769K BYTES FREE MEMORY AS6 H8 ROOO R200 W10
25. ition of print head when printing The setting value is from 100 to 100 Default Thermal Transfer Thermal Transfer when printing a ribbon must be installed Printing mode to transfer the print contents onto the media Direct Thermal when printing no ribbon is necessary it only requires direct thermal media Default Option OFF Strip Mode turn on the stripper function Option Setup Cutter Mode turn on the cutter function Applicator Mode turn on the applicator function None select this to turn off the stripper and cutter functions Default Gap paper Black Mark for label or plain paper with black mark in the back Gap for labels with liner and gap or hang tags The default is set to be gap paper Continuous for continuous paper Sensor Setup EZ 2000 6000 Users Manual Rev D 40 Baud Rate Default 9600 bits 4800 bits 9600 bits 19200 bits 38400 bits 57600 bits 115200 bits Parity Default None Parity COM Port Set None Parity Odd Parity Even Parity Data Bits Default 8 bits 7 bits 8 bits Stop Bits Default 1 bit 1 bits 2 bits Default Auto Mode Auto Mode auto sense the label type black mark gap amp plain Auto Sensor Mpaper and length Gap Mode detects gap paper Black Mark Mode detects black mark label Default English English Simplified Chinese Traditional Chinese LCD Language Spanish Italian Deutsch French Default Code Page 850 Code Page Code Page850 Code
26. ix code amp QR code Serial port RS 232 Baud rate 4800 115200 Xon Xoff DSR DTR USB port V2 0 CF card socket Ud eet Back lit LCD Display 128x64dots Graphic LCD Control Panel Tas GET keys Three single color LEDs Power Ribbon Media FEED PAUSE CANCEL Three control keys FEED PAUSE CANCEL Power 100 240VAC 50 60 Hz Real Time Clock Standard Operation 41 F to 104 F 5 C to 40 C Storage 4 F to 122 F 20 C to 50 C Humidity Operation 30 85 non condensing Free air Storage 10 90 non condensing Free air Length 512 mm 20 15 Height 291 mm 11 45 Width 274 mm 10 78 Environment Printer Dimension Weight 15 Kg Cutter Internal re winder Ethernet Adapter Parallel PS2 Adapter Applicator Interface 1 input 3 outputs power 500mA 5V Specifications are subject to change without notice EZ 2000 6000 Users Manual Rev D 11 Model EZ 6200 Plus EZ 6300 Plus Resolution 203 dpi 8 dot mm 300 dpi 12 dot mm Print Mode Thermal Transfer Direct Thermal CPU 32 Bit Memory 4MB Flash 16MB SDRAM Print Speed 2 IPS 6 IPS 2 IPS 4 IPS Print Length Min 13mm 0 51 Max 3000mm 118 Min 13mm 0 51 Max 1371mm DAT Print Width 168 mm 6 61 Sensor Type Adjustable transmissive sensor and reflective sensor left aligned Type Label gap and black mark sensing Detection Label length auto sensing or program command setting Sensor Detection Label Ro
27. lace with new label roll Possible causes card tags paper falling into the gap behind the platen Deng e roller can t find setting label gap black mark black mark paper out Please adjust according to actual usage Please follow the Instruction on Chapter 5 8 to format the CF Card CF Card is not formatted CF Card blinking not found simultaneously EZ 2000 6000 Users Manual Rev D 46 i Delete unnecessary Memory 2 beeps Memory is i or use CF Card Rewinder 2 beeps Rewinder is Remove the labels Full P twice full on rewinder Use X4 i command to print E ch 2 2 beeps Can t find out all the files then found Z twice the file check whether the file exist and the names are correct Filename S 2 beeps File name an ae repeated VE twice is repeated download again EZ 2000 6000 Users Manual Rev D 47 o Maintenance and Adjustment 5 1 Print Head Module Installation Removal Instruction 1 Open the top cover Note Power off when removing print head module Pull the Print Head Lever out and flip it upward to the right Note When remove print head module please dismount the cutter first To remove the print head module hold on the front of the print head module and pull it out If user cannot successfully remove the print head by hand the screwdriver can be used for assistant as the figure shows To install the print head module h
28. ll Max 203mm 8 0 with 76 2mm 3 ID core Core Diameter 38 1mm 1 5 76 2mm 3 Width Tear 50 8 mm 2 178 0mm 7 Width Cutter Max 165mm 6 5 Width Heavy duty cutter Max 172mm 6 8 Width Stripper Rewind 50 8 mm 2 gt 178 0mm 7 Thickness 0 06 0 25mm Length 450 m 1471 ft Ribbon Type transfer ribbons wax hybrid and resin in widths of 60 to 174 mm 2 36 to 6 85 Auto ink inside and ink outside Core inner diameter 25 4 mm 1 Max ribbon roll diameter 76mm 2 99 Application QLabel IV EZPL only Software BPP amp Driver Microsoft Windows NT 4 0 2000 and XP 11 resident alphanumeric fonts included OCR A 8 B those are expandable 8 Resident Fonts times horizontally and vertically All bit mapped fonts in 8 orientations Scalable Fonts Code Page 850 amp 852 in 4 orientations Fonts Download Windows bit mapped in 8 orientations True Type font Ver 2 XX and Asian fonts In 4 orientations Image Handling BMP PCX Support ICO WMF JPG EMF file through software Code 39 Code 93 Code 128 subset A B C UCC EAN 128 K Mart UCC EAN 128 UPC A E add on 2 amp 5 2 of 5 2 of 5 with Shipping Bearer Barcode Bars EAN 8 13 add on 2 amp 5 Codabar Post NET EAN 128 DUN 14 MaxiCode HIBC Plessey Random Weight Telepen FIM China Postal Code RPS 128 PDF417 Datamatrix code amp QR code Serial port RS 232 Baud rate 4800 11
29. n f hren EZ 2000 6000 Users Manual Rev D 2 Safety Instructions Please read the following instructions seriously 1 Keep the eguipment away from humidity Before you connect the eguipment to the power outlet please check the voltage of the power source Disconnect the eguipment from the voltage of the power source to prevent possible transient over voltage damage Don t pour any liquid to the equipment to avoid electrical shock ONLY qualified service personnel for safety reason should open equipment Don t repair or adjust energized equipment alone under any circumstances Someone capable of providing first aid must always be present for your safety Always obtain first aid or medical attention immediately after an injury Never neglect an injury no matter how slight it seems EZ 2000 6000 Users Manual Rev D 3 CE VERIFICATION OF COMPLIANCE This Verification of Compliance is hereby issued ro the below named company The test results of this report relate only ro the tested sample identified in this report Technical Standard EMC DIRECTIVE 89 336 EEC EN 55022 EN 55024 General Information Applicant GODEX INTERNATIONAL CO LTD 4F No 168 Liancheng Rd Jhonghe City Taipei County 235 Taiwan R O C Manufacturer GODEX INTERNATIONAL CO LTD 4F No 168 Liancheng Rd Jhonghe City Taipei County 235 Taiwan R O C Product Description EUT Description Therma Transfer Printer Model
30. nstallation completes EZ 2000 6000 Users Manual Rev D 27 3 2 Rewind Bracket Installation for EZ 2000 EE 1 Face the printer front and unscrew the bottom cover screw 2 Remove the bottom front Cover Note Before the installation please power off the printer first 3 Mount the label rewind bracket onto the printer mechanism and secure the screws into place Label rewind bracket installation completes Install the media into the printer Feed the label through the Printer Mechanism and around the Label Feed Guide Wrap the label around the Liner Rewinder Shaft and use the U Shape Clip to secure the liner Note Make sure the label rewind is in correct direction EZ 2000 6000 Users Manual Rev D 28 Close the top cover to complete Label rewind bracket and Rewinder installation Note1 Before starting to rewind labels please make sure the printer s Label Rewind Bracket is installed properly as instructed Note2 When use stripper function Please dismount the rewind bracket first EZ 2000 6000 Users Manual Rev D 29 a 3 Stripper Installation for EZ 2000 Plus Face the printer front and unscrew clockwise the bottom front cover screw 2 Remove the bottom front cover Note Before the installation please power off the printer first After Rewinder installation complete face the printer sideways Pull the print head l
31. o prolong the print head life Print head cleaning instructions are as follows Power off the printer Open the top cover Take out the ribbon Open the print head by lifting the Print Head Lever If there are label pieces or other stain on the print head see blue arrow please use a soft cloth with industrial use alcohol to wipe away the stain Note 1 Weekly cleaning on the print head is recommended Note 2 When cleaning the print head with soft cloth make sure there is no any metal or hard particles attached on it EZ 2000 6000 User s Manual Rev D 51 5 5 Print Head Balance and Pressure Adjustment 1 Open the top cover Pull the Print Head Lever out and flip it upward to the right When printing with different label materials or using different ribbon types unbalanced print quality may occur due to the media material differences Moreover when one side of the printout is not printed clearly or ribbon wrinkle occurs it s necessary to adjust the position or pressure of TPH Spring Box 3 Move the TPH Spring Box as showed on the figure to change the print position Normally the wider the paper the right TPH Spring Box is farther to the right out the narrower the paper the right TPH Spring Box is farther to the left in If the problem is still not solved please move to next step to adjust the pressure of TPH Spring Box To adjust the T
32. old on the front of the print head module and slide down along the track Align the male end with protruding pins with the female end pin base and push the print head module down EZ 2000 6000 Users Manual Rev D 48 5 2 TPH Print Line Adjustment Please contact your local dealer for technical support 1 Open the top cover Pull the Print Head Lever out and flip it upward to the right TPH print line adjustment When the printing is stiff or printing with thick paper the print line needs to be moved forward paper feed direction in order to achieve better printing quality Use a flat tip screwdriver and turn the screws A clockwise to move the TPH forward TPH position adjustment for the left and right screws A need to be identical to make sure that the print line and the roller platen are parallel to each other Turning the screws A one circle the TPH will move 0 5mm It is recommended to adjust by a quarter of a circle each time to fully control the printing quality and status If the adjustment is failed please slowly turn the screws A counterclockwise all the way to the end using a flat tip screwdriver And redo the adjustment from the beginning EZ 2000 6000 Users Manual Rev D 49 5 3 Ribbon Tension Adjustment The ribbon shaft tension can be adjusted by turning the ribbon shaft knob clockwise or counterclockwise There are 4 different levels of tension and marked with 1 4
33. on will be taken for products not in conformance with UL s requirements and continued use of the UL Mark may be withdrawn Sincerely Reviewed by n E Pudge a Ara M r ope Jim Kaa Joseph Chang i Engineer Project Engineer Department 30135T Al Department 3013BTA Tel 02 26967790 E mail joseph chang amp tw ul com Fax 02 2890 7430 E mail jim kao idtw ul com CC Compliance Certification Services Inc E mail peifang wud itw ccsemc com Attn Ms Grace Wu EZ 2000 6000 Users Manual Rev D 8 1 BARCODE PRINTER 2222er 10 1 13 PIIMIEF ACEESSONES ira nea eine nike Mai vanili elan 10 1 2 ENEE te LE 10 1 3 Communication Interface nena 13 PTL Parts oa en nao r at u oa dl han 16 2 PRINTER INSTALLATION 22 19 ERE e Rat de WEE 19 2 2 nibbon Installation nes ensure 22 234 PG Gonnecl nsseea een 24 2 4 Driver Installation EE 25 3 AGGESSOR Vs TETE ET ae 26 3 1 Internal Rewinder for EZ 2000 blue 26 3 2 Rewind Bracket Installation for EZ 2000 Plus eee nene 28 3 3 Stripper Installation for EZ 2000 TC 30 3 4 G ter Installations sa lee 32 3 5 Parallel PS2 Adapter Installation nn 34 4 CONTROL PANEL oooeeoone KEREN KEREN KEE nanosa nano ena uses KEEN 36 4 1 Control Panel Introduction na 36 4 2 Control KEY Se Leit ele de EE 37 E dn Te Bee e EE 39 4 45 SEIT ES nennen 44 4 5 DUMP Mode EE 45 4 6 JOO CA O ara ae Bee hal 45 A EMOCMOSSageS un rien 46 5 MAINTENANCE AND ADJ
34. ort Setup Auto Sensor LCD Language CodePage Setup Keyboard Setup Keyboard Mode Buzzer Setup Srrart Backfeed Password Too of Form Ethene 2 7 0 60mm 100 100 Thema Transfe Direct Thema Strip Moce Cutter Mode Appicdor Mode None Black Mak Gap Continuous Baud Rae Panty Daa Bits Stop Bits Auto Mode Gap Mode Black Mak Moce Engisi Simplified Chinese Tradtiona Chinese Espanol Itdiano Deutsch Fragas T rkce Code Page 850 Code page 852 US UK French Genre Spanish Italian Finnish Dutch Bdgan Recall Laod Keyboard Setup Code page setup Printing Opion ClokSdup ExitKB Mod Enter Keyboard Code Page 850 Printer Prorpts Recall Land Clock Saiting Code page 852 Indefinite Sdect Laba Clock Display Fixed Print Ouartity ON OFF ON OFF ON OFF ON OFF Go to defauit Preview Items w
35. print completely Check the media quality The printout is not in desired position Check if sensor is covered by paper or dust Check if liner is suitable for use please contact reseller for more information Check if label roll edge is aligned with Label Width Guide When printing page skipping occurs Check if error occurs on label height setting Check is sensor is covered by dust Unclear printout Check print darkness setting Check if Thermal Print Head is covered with glue or stain straight successfully 0 16mm unexpected cutting occurs Check if Paper Feed Rods are sticky working correctly Check if label is installed properly Note Your dealer is knowledgeable about GODEX printers printing software and your unique system Please contact your local dealer for technical support EZ 2000 6000 Users Manual Rev D 55
36. r clockwise to remove the jammed label After the jammed label is removed power on the printer again The cutter will reset automatically Note The label paper used for cutting is suggested to be at least 30mm in height 5 8 CF Card Instruction All the EZ 2000 Plus and EZ 6000 Plus series models have built in CF Card slot on the back of the printer If the built in memory is insufficient for storing label formats graphics or fonts users can use CF Card as external memory to provide more memory space When using the CF card please follow the instruction as below 1 Please power off the print before installing or removing CF Card from the card slot 2 The CF Card cannot be used for printer s external memory until it is formatted in FAT16 When the printer has detected that the CF card is not formatted in FAT16 the LCD will show the message of CF card not formatted press FEED to format 3 If user wants to format the CF Card please follow the instruction to press the FEED key and then the printer will format the CF Card in FAT16 4 After the format is complete a file folder named Godex would be created automatically This folder is for storing all the data from the printer please dont do any change on it 5 The capacity of CF Card that is supported by the printer is from 128MB to 1GB EZ 2000 6000 Users Manual Rev D 54 Problem Recommended Solution LCD Display shows no message after
37. s with paper weights 200g Note3 The service life of EZ 6000 Cutter is 500 000 cuts Face the printer and unscrew the screw to remove the bottom front cover Note Please power off the printer before installing the cutter module 2 Open the top cover and unscrew the two screws in the front to remove the tear off bar EZ 2000 6000 Users Manual Rev D 32 Hold the cutter and secure the cutter kit onto the printer Plug the cutter cable connector onto the cutter connector Tie the cables with the secure locks and stick the locks onto the bottom plate Hang up the cutter cover to the cutter and screw the bottom Cover screw Install the media into the printer Close the Top Cover to complete the cutter installation Note1 k Make sure the printer is set to ele activate cutter function on 0 Plus 6000 Plus Note2 The label paper used for cutting is suggested to be at least 30mm in height Suggestion When installing the cutter module set the stop position to 26 for EZ 2000 or 30 for EZ 6000 in QLabel and the E value is 26 for EZ 2000 or 30 for EZ 6000 EZ 2000 6000 Users Manual Rev D 33 3 5 Parallel PS2 Adapter Installation 1 Parallel Cable Fa 2 Parallel PS2 Adapter KA 3 Connector Cable 1 ECH 4 Screw x 2pcs E Make sure the power is off and the power cable is unplugged Place the print
38. services are provided on behalf of Underwnters Laboratones Inc UL or any authorized licensee of UL UL s investigation of your product has been completed under the above project number and the subject product was determined to comply with the applicable requirements This letter temporarily supplements the UL Follow Up Services Procedure and serves as authorization to apply the UL Listing Mark only at the factory under UL s Follow Up Service Program to the subject products which are constructed as described below similar to products covered in the UL Follow Up Services Procedure File E214553 Volume X1 To provide the manufacturer with the intended authorization to usethe UL Mark the addressee must send a copy of this Notice and all attached material to each manufactunng location as currently authonzed in File F214683 Volume X1 This authorization is effective from the date of this Notice and only for products at the indicated manufacturing locations Records in the Follow Up Services Procedure covenng the product are now being prepared and will be sent to the indicated manufacturing locations in the near future Please note that Follow Up Services Procedures are sent to the manufacturers only unless the Applicant specifically requests this document Products that bear the UL Mark shall be identical to those that were evaluated by UL and found to comply with UL s requirements If changes in construction are discovered appropriate acti
39. sing position 2 Power off the printer press and hold the Cancel key 3 Power on the printer while still holding the Cancel key after printer beeps 3 times and the LCD Display shows Auto Sensing mode release the Cancel key Printer will automatically detect the label size length and record 4 LCD Display shows the results of measurement Printer goes back to standby mode after displaying the measurement EZ 2000 6000 Users Manual Rev D 45 4 7 Error Messages If problems occur that prevent the printer printing normally the printer will beep as warning and error messages will be displayed vilu oe e Quickly blinking Slowly blinking Lightison n EH h TI Message i Thermal Re open the Print Head both lights Print Head Thermal Print Head is opened are on is not firmly and make sure it is closed closed tightly Entering Thermal the ao blinking Print Head Cooling ZN Zw simultaneously temperatur Process e high Ribbon not installed and printer Out of shows error ribbon or message check Ribbons ribbon used up or sensor ribbon Replace with new supply ribbon roll shaft not Printer goes back to standby mode after cooling Make sure the printer is in the Direct Thermal mode Make sure the movable sensor mark is at the Unable to correct position if media or detect the sensor is still check i unable to detect media gap paper and then go sensor through Auto Sensing again Rep
40. st the position with Moveable Sensor Lever EZ 2000 6000 User s Manual Rev D 20 i wr a m n a JE e Align the label edge inward and fix the label outside in Label Guide Adjust the Label Guide with the label Note The Label should be put within Label Feed Guide as the figure shows 10 Flip the Print Head Lever back to its Original position Close the top cover to complete the label installation EZ 2000 6000 User s Manual Rev D 21 2 2 Ribbon Installation Place the printer on a horizontal surface and open the top cover Follow the seguence and direction as the figure shows pull the Print Head Lever out and flip it upward to the right Place a new ribbon roll onto the Ribbon Supply Shaft and place the empty ribbon roll onto the Ribbon Rewind Shaft The right bottom figure shows two different installing directions according to s types of Ribbon outside installation Ribbon inside installation ink outside the roll ink inside the roll O A Ink EN Outside gt fo Inside 4 KRK ERN Va KRA OO Ink Outside mo o Inside ER dE REESS A N QRS ET
41. yy x 0 9 y 0 9 a 7 Brand Name GODEX THARO ACCUMAX SYSTEM WAVE Laboratory Name Compliance Certification Services Ine Tainan Lab No 8 Jiu Cheng Ling Jiaokeng Village Sinhua Township Tainan Hsien 712 Taiwan RO Tel 886 6 380220 Fax 886 6 3802202 This device has been shown to be in compliance with and was tested tu accordance with the measurement procedures specified in the Standards amp Specifications listed above and as indicated in the measurement report number 61030405 D po FOP Ce Alex Chiu Manager Date November 07 2006 74 EZ 2000 6000 Users Manual Rev D 7 HE RESNE SERCE Underwriters Laboratories Underwriters Laboratories Talwan Co Ltd Taiwan Go Ltd Sih 11268 B K Rome UF 280 Da Yeh Road Patou Tnipal City Talwar 112 Tot 808 2 2908 7700 Fox 98 3 2091 29044 https ww LOOM PA NOTICE OF AUTHORIZATION TO APPLY THE UL MARK January 12 2007 MR Wallace Tsai Godex International C O Compliance Certification Services Inc 6th FL 605 Jhongshan Rd sinhua Township Tainan Hsien 71243 Tw Fax number 2 22408795 E mail wallacetsai gqodex com tw Reference File E214683 Project 06NK90314 Report Reference Number E214683 A2 UL 1 Amendment 1 Product s USL UL CUL FOR PRINTER Model EZ 6xxxPyyy where x 0 9 y 0 9 az employing the alternate R C power Mean Well Type USF225 24 and main board Dear Mr Tsal Any information and documentation involving UL Mark
Download Pdf Manuals
Related Search