UM08 User's Guide
Contents
1. 4 BRIGHTNESS HIP 40 5 D WDR OFF 6 DEFOG OFF 7 RETURN RET 1 2 3 4 5 6 Shutter Digitally control amount of light the amount is smaller the image is darker and the frame rate is also slower AGC Auto Gain Control auto control the brightness based on setting when light is not enough SENS UP Only available when item 2 AGC value is larger than 0 use to increase Senor to light s sensibility Brightness Adjust image brightness D WDR Digital wide dynamic range Digitally adjusting exposure in areas of the frame to maintain optimum detail in both the shadows and highlights of the image DEFOG De Fog When observing under strong light or special environment use Defog function to see clear image Below fig for De Fog setting DEFOG LPOS SIZE ll 2 GRADATION LOW 3 DEFAULT lt 4 RETURN RET 6 1 POS SIZE Adjust de fog position and area 11 6 2 GRADATION To set gradation levels near the edge of defog area 6 3 DEFAULT Return to default setting 6 4 RETURN Return to last page 1 4 2 BACKLIGHT Press left right button to choose turn on off Backlight mode 1 OFF Disable backlight function 2 WDR Wide Dynamic Range WDR allows an imaging system to correct for the intense back light surrounding a subject and thus enhances the ability to distinguish features and shapes on the subject See below for setting WDR WDR 1 GAIN LOW 2 WDR OFFSET pi O 3 RETURN2. 4 2 1 START Start to do Static Dead Pixel correction 4 2 2 LEVEL Set the threshold value to judge if it needs 21 to be corrected 4 2 3 SENS UP Raise up the sensor s sensitivity to compensate the dead pixel 4 2 4 AGC Auto Gain Control When light is not enough AGC will follow the threshold setting to compensate the dead pixel 4 2 5 RETURN Return to last page 4 2 2 to be corrected 5 VERSION Firmware version 6 RETURN Return to last page 1 4 6 ADJUST See image adjust as below fig AD JUST 1 SHARPNESS HIP 8 2 LSC OFF A 3 RETURN RET 1 SHARPNESS Adjust Sharpness higher value increases the higher contrast along near edges of the image 2 LSC Lens Shading Correction Use Lens shading correction to average the luminance of image 22 1 4 7 RESET Return to factory default setting Press Left right button to choose CHANGE to return default RESET 1 FACTORY RESET A 2 RETURN RET 1 4 8 RETURN Exit from menu 1 5 Microscope introduction 1 5 1 IR Remote Area Indicator When both 9 and hLED indicator blinks the microscope is in standby mode Caution Please remove the transparent protection sheet on the IR receiver area 23 1 IR remote control aiming areaQ f The indicator will blink whenever buttons are pressed If the indicator did not blink means the signal was not delivered and please repress again 2 HDMI indicator g When lit up the microscop
3. Digital Zoom Ex DZ x4 0 means digital enlarge 4x 16 2 9 SHA Sharpness Ex SHA SET 5 means sharpness is 5 SHA SET 15 means the maximum 15 16 2 10 FRZ Image Freeze Ex FRZ ON means freeze image FRZB OFF means unfreeze image 16 2 11 WB White Balance Ex WB SET means calibrate white balance 16 2 12 NONE No Function 17 Auto White Balance Calibration To calibrate the white balance place the white balance card included in box under the lens focus until clear and choose On Because the white 8 balance is sometimes influenced by external light sources it is recommended to calibrate the white balance if the color seems off or incorrect J f 2 a NOIRS B 18 image eo ON Off to freeze or unfreeze the image 19 Sharpness On Off to set sharpness at Minimum and Maximum level 1 4 Microscope menu functions There are 8 functions in menu press Up and Down to choose item Left and Right to turn on off or adjust parameter 9 Enter means more functions press Menu to enter next function or confirm means no more settings Return to return last page or press Left or Right to choose End to return preview window MAIN MENU EXPOSURE ol 2 BACKLIGHT OFF 3 WHITE BAL 4 NR 5 SPECIAL 6 ADJUST Z RESET 8 EXIT ttttt gt 1 4 1 EXPOSURE To set exposure time see below EXPOSURE 1 SHUTTER AUTO 2 AGC JUL O 3 SENS UP
4. color from current image 4 MANUAL Manually adjust blue and red values to find correct white color Refer to below fig MANUAL WB 1 BLUE HN 50 2 RED HIP BO 3 RETURN RET 1 4 4 NR Noise Reduction NR To obtain high quality output image and increase file compression See below 2D83D NR 1 2DNR ON 2 3DNR ONA 3 RETURN RET 1 2D NR ON OFF Edge Preserving 2D NR 2 3D NR ON OFF Motion Adaptive 3D NR See below 3D NR 1 SMART NR OFF 2 LEVEL HN 85 3 START AGC LUN O 4 END AGC JU O 5 RETURN RET 3 1 SMART NR Distinguish the moving object not moving noise and auto close the 3D NR 3D SMART NR L SENSITIVITY HN SO 2 RETURN RET 3 1 1 SMART NR The sensitivity to detect the moving object The lower value gets higher sensitivity 3 1 2 RETURN Return to last page 3 2 LEVEL The threshold to judge noise 3 3 START AGC Start auto gain control When AGC value is higher than setting will start auto gain 3 4 END AGC End auto gain control When AGC value is higher than setting will end up auto gain 3 5 Return Return to last page 3 Return Return to last page 16 1 4 5 SPECIAL Set special functions SPECIAL L D lt EFFECT ad 2 MOTION OFF 3 LANGUAGE ENG 4 DEFECT lt 5 VERSION 010000 6 RETURN RET 1 D EFFECT There are few more functions in D EFFECT but 1 3 1 4 and 1 6 function can only turn on one item at one time Press Left or right to turn on or
5. 07 657 9561 Address 10 F No 1 Section 1 Syuecheng Road Dashu District Kaohsiung City 840 Taiwan R O C Website http www vitiny com HTTP WWW VITINY COM MicroLinks Technology Corp All rights reserved
6. off See below functions D EFFECT JFREEZE OBE 2 MIRROR OFF 3 D ZOOM OFF 4 SMART D ZOOM OFF 5 NEG IMAGE OFF 6 DIS OFF 7 RETURN RET 1 1 FREEZE Turn ON OFF to freeze image If Freeze function is turn on the 1 2 Mirror function can not be used at the same time 17 1 2 MIRROR Image rotatory Horizontal or Vertical 1 3 D ZOOM Digitally enlarge the chose area Digital zoom selection can from 1 62 times See below setting for D Zoom D ZOOM 1 PIP 2 D ZOOM X 2 0 3 PAN amp TILT d 4 DEFAULT a 5 RETURN RET 1 3 1 PIP No function 1 3 2 D Zoom Set digital zoom times 1 3 3 PAN amp TILT To set the enlarge position 1 3 4 DEFAULT Return to default setting 1 3 5 RETURN Return to last page 1 4 SMART D ZOOM Assign 1 or 2 areas to enlarge the image from 1 62 times whenever detected the object moves The Smart D zoom will automatically enlarge the assigned area for few seconds and then return to original image 18 1 4 1 1 4 2 1 4 3 1 4 4 1 4 5 1 4 6 1 4 7 1 4 8 1 5 NEG SMART D ZOOM LSELEGT AREA1 2 DISPLAY ONA 3 SENSITIVITY MANN 3 0 4 PIP os 5 D ZOOM X 4 0 6 TIME HE 3 7 DEFAULT ol 8 RETURN RET SELECT Choose the enlarge area totally 2 areas DISPLAY Display enlargement frame Position and area can be set in 1 4 1 SENSITIVITY The sensitivity to detect whenever object moves The lower value gets the higher sensitivity PIP No Fu
7. to decrease exposure when the image is too bright 10 Menu on Screen Open close menu for setting Refer to Section 1 4 11 Up Choose the previous item 12 Down Choose the next item 13 Left Choose the next value 14 Right Choose the last value 15 Video Ratio 8 Digital zoom function can set x1 0 x2 0 x4 0 and x8 0 16 Status Bar Status bar tells Field of View FOV Magnification MAG or ON OFF the status see area 4 The area _ e tells the operation status and only show 3 seconds pak MAG 141 Btax EE 16 1 Area Od 16 1 1 FOV Field of View FOV display image on the effective horizontal size of screen 16 1 2 MAG Magnification The magnification size will change depending on the lens position screen size and image ratio 16 1 3 WD Working Distance 16 2 Area e 16 2 1 OZ Optical Zoom Ex OZ 4500 L means zoom in 500 means sensor position 16 2 2 SZ Step Zoom Ex SZ 1500 Same format as OZ 16 2 3 AFS Single Autofocus Ex AFS A500 A means 7 search focus in current area 500 means sensor position AFS W500 W means search focus in whole area 16 2 4 AFC Continuous autofocus A and W are same function as AFS 16 2 5 LED LED levels Ex LED 12 12 means the LED level 16 2 6 EV Exposure Value Ex EV M5 means EV is 5 EV 5 means EV is 5 16 2 7 MR Motor Reset 16 2 8 DZ
8. 40 995 940 _ WD mm 175 0 69 5 64 0 58 5 155 5 152 5 49 5 147 0 440 _ FOV mm 13 12 11 10 95 9 185 8 75 ee Focus section 19 20 21 22 23 24 25 26 Sensor position 885 815 730 635 520 390 215 40 WD mm 41 0 38 0 35 0 32 5 30 0 27 5 25 0 225 FOV mm 7 65 6 55 5 45 4 36 Mag X 68 1 73 4 79 5 86 7 95 4 106 119 132 30 10X object lens focus distance from 6 2mm 10mm 0 244 0 393inch 10X object lens on 21 5 Reference data Faisons 2 o ee WD mm 10 9 7 94 9 1 88 85 182 179 176 2 1 1 7 1 5 207 216 227 a l Focus section 10 11 12 13 14 Sensor position 920 740 530 270 40 J WD mm 73 70 67 64 62 J 7 Fovimm 14 13 12 11 02 J J Mag X 340 1366 397 433 467 1 7 Microscope accessory 1 7 1 White balance card The white side is used to calibrate the white balance If the object is tiny place it onto the white balance card and move the card instead of the object 31 2 Printed Notice Please read the following information before operating 2 1 Maintenance Please abide by the following rules while storing or using this product 2 1 1 Keep dry do not place the product in a humid environment Dry surroundings help extend the life of the product 2 1 2 Avoid temperature shock temperature shock for example taking the product into a Warm room from a cold environment
9. DC 5 0V 2 0A Input AC 100 240V 50 60Hz Power 0 225A Max Consumption A C 106 L x106 W x152 T mm Host weight around 310 grams Operation Temperature 5C 50 C Humidity lower than environment 85 No Condensation For any changes please visit http www vitiny com 33 Safety Instructions As an electronic product please do not use the device in any place in which electronic products are prohibited Keep the device away from water sources to avoid electric shock as it is not waterproof Keep the device away from chemicals or substances with explosive or fire hazards Switch the device off near gas stations In the case that there are foreign substances or water inside the device or the device is dropped or damaged please switch off and remove the power supply to avoid fire and electric shock Do not look steadily into Light sources after switching on the host as it is harmful to your eyes Please use only the product accessories provided in the box for connections Do not use any outside products without approval of original factory Please remove the power supply from the microscope when not in use Do not disassemble the machine for inspection For any problems occurring in the machine itself please power off the device and contact us through e mail mltc vitiny com 34 35 ViTiny UMO8 Warranty Product O Modelno O SA O Purchase DD MM YYYY date Purchaser Teno O Address O Ema
10. RET 2 1 GAIN Set WDR gain level to raise up brightness of darker image 2 2 WDR OFFSET Wide Dynamic Range OFFSET 2 3 RETURN Return to last page 12 3 BLC Back Light Compensation To adjust brightness for darker image in back light environment 3 1 GAIN To adjust brightness level 3 2 AREA Choose the back light compensation area and size 3 3 DEFAULT Return to default setting 3 4 Return Return to last page or press left or right to choose End to return preview window BLC 1 GAIN MIDDLE 2 AREA wel 3 DEFAULT 4 RETURN RET 4 HSBLC High Suppress Back Light Compensation To identify the over luminance area by backlight and proceed masking the area 13 HSBLC SELECT AREA1 2 DISPLAY ON 3 LEVEL mpn 20 4 MODE ALL DAY 5 BLACK MASK ON 6 DEFAULT lt 7 RETURN RET 4 1 SELECT Select the areas which needs to be adjusted 4 areas are selectable 4 2 DISPLAY Display the selected area 4 3 LEVEL Set value to judge if the image is too bright 4 4 MODE Super back light compensation mode 4 5 ALL DAY Day mode 4 6 NIGHT Night mode 4 7 BLACK MASK Reverse the over exposed area 4 8 DEFAULT Return to factory default setting 4 9 RETURN Return to last page 1 4 3 MANUAL WB Calibrate the white balance 1 AWB Auto white balance 2 ATW Auto tracing white area and calibration 14 3 AWC gt SET Semi auto white balance Use to track the white
11. Tie ymMos User s Guide DiGi Microscope Version 1 0A Contents Product Introduction cccceceeeeeees 2 1 1 Packing Contents 2 1 2 Assemble microscope with stand 2 1 3 IR Remote controller 4 1 4 Microscope menu functions 9 1 5 Microscope introduction 23 1 6 Microscope FOCUS 27 17 Microscope accessory 31 Printed NOCE neninn sn 32 2 1 Maintenance 32 2 2 Product Specification 33 2 3 Safety Instructions 34 1 Product Introduction 1 1 Packing Contents The box contains 1 microscope and 8 accessories The Object Lens 4X is already assembled onto microscope DiGi Microscope White Balance Card HDMI Cable IR Remote Control S107 Stand Object Lens 4x Stand assemble guide Object Lens 10x 1 2 Assemble microscope with stand 1 2 1 Fix microscope Tighten the microscope onto stand a Refer to Stand assembling instruction for detailed explanation LELLET E 5 se LA H Btac Me X ET mie ONVO ba Lo bay H r an LETILL 1 2 2 Start to use microscope Connect the HDMI cable b and adaptor c within the box to HDMI monitor and power See below Btac DS etree eee N k mme ee PL kuk sloku j f j E j j 4 mm ve me L ee eee eee eee iko LL 1 2 3 Power On Off Press Power to turn o
12. e is in HDMI mode If light blinks means microscope does not connect with monitor 24 1 5 2 Power USB HDMI port Caution Please hold the cable when remove from microscope and do not disassemble cables forcefully gs HF 0 USB fee T FE S A 4 M moon 1 lOsdP ioooo Jooo o eee ee LEETE eee 1 HDMIC i The HDMI port is used to connect the microscope to a screen When the device is in HDMI mode connect the microscope to the screen using the HDMI cable from the box For TV screen connections make sure to choose the homologous image ratio and format 2 USBO i USB port to use for future firmware update 3 Power Power adaptor is only compatible with the cord in the box 25 1 5 3 Stand gear box Assemble the stand and then screw the microscope onto the universal joint on the gear box 1 5 4 LED Light socket 1 LED m Provides luminance for object lens 4x total 30 LEDs 2 Light socket n Provides luminance for object lens 10x Optional accessory 26 1 6 Microscope Focus There are two ways to focus First choose focus distance to adjust the microscope height then tuning focus by remote controller until clear On the contrary first to choose the image sensor position then adjusts the microscope height Focus distance distance from object lens to object Image sensor position The image sensor position 1 6 1 Focus T
13. echnigues 1 Fixed focus distance 27 Use knob cor pto adjust the distance from the object lens to the object When the distance is closer the magnification size is higher When the focus distance is fixed use the remote controller or far distance control mode on the application program to focus the image 2 Fixed image sensor position The status bar will show on the screen please refer to Section 1 3 16 Use the remote controller to adjust the image sensor position based on magnification size FOV or working distance When the image sensor position is fixed focus the image by using knob to adjust the height and knob to fine tune 28 1 6 2 Magnification chart 26 focus section setting is based on the whole focus area per 4x object lens 10x object lens only have 15 focus sections The sensor position tells the magnification size Mag field of view FOV or working distance WD The below chart is measured on 4 3 ratio on 21 5 screen it s only a reference data might not be accurate enough Based on the image ratio preview window size field of view and magnification size will change 29 1 4X object lens focus distance from 22 5mm 226mm 0 885 8 897inch 4X object lens on 21 5 Reference data O BS OT S C O Sensor position 1615 1595 1565 Fov mm 40 35 30 25 20 18 16 15 14 aaa SSS Sensor position 1290 11250 1205 1150 1115 1080 10
14. l O Distributor Seal for Confirmation Stamp is necessary for validation of the Warranty X Distributor s seal shall include name of the shop telephone and address Please ask the distributor to fill in the name of the shop address purchase date and other contents to protect your rights and validate your one year Warranty since upon the purchase date Contents of Warranty The warranty is provided free of charge for faults caused by manufacturing within one year from the purchase date Non warranty 1 Product appearance parts such as the outer casing knobs and LED cover etc charged spare parts are limited to one year after completing the product manufacturing Consumption goods of the host itself such as LED lights and lens Product accessories and fittings such as the power supplier HDMI cable white balance card remote controller etc Services caused by any of the following situations in the period of the Warranty shall not be provided free of charge l 2 3 Improper use or disassembly repair or refitting Any damages to the device caused by external or environmental factors Discrepancy of product serial number unfilled or unidentified warranty Any inspection or repair service after the period of warranty will be charged as follows 1 Service fees including transportation fees of product inspection 2 Repair fees 3 Fees of replaced parts ViTiny Service Center Tel 07 657 9551 Fax
15. n microscope Choose HDMI mode or Auto on HDMI monitor to output image x H Optical Zoom Va A 1 Ne K a N n ve LS 7 Q 4 3 2 1 3 IR Remote controller The microscope operation and functions is controlled by the IR remote controller 1 Power Turn on off 2 HDMI No Function 3 PC CAME No Function 4 Snapshot No Function 19X18 15 17 5 LED Adjustment 12 levels of brightness 5 1 Increase Increase LED brightness 5 2 Decrease Decrease LED brightness 5 3 On Off Turn the LED on off When turn on the LED the brightness will return to the situation before turn off 6 Motor Reset Recalibrates entire operation Returns to the lens position If a loss of electricity occurred during operation please reset the operation 7 Manual focus 7 1 Zoom in Zooms in speed increases when held 7 2 Zoom outG Zooms out speed increases when held 7 3 Step zoom in zoom in by steps 7 4 Step zoom outG zoom out by steps 8 Autofocus Press one time to search focus in current area press and hold for 2 seconds to search focus in whole area 8 1 Single Autofocus Focuses one time 8 2 Continuous autofocus Re focuses when image blurred 9 Exposure Value 18 levels of exposure value are selectable from 9 Auto 9 9 1 Increase Use to increase exposure when the image is too dark 9 2 Decrease Use
16. nction D Zoom Set magnification times TIME Set the enlargement waiting time DEFAULT Return to default setting Return Return to last page IMAGE Turn On Off Negative image 1 6 DIS Digital Image Stabilization function 19 1 7 RETURN Return to last page 2 MOTION Detect the moving object see below setting MOTION LSELECT AREA1 2 DISPLAY ONA 3 SENSITIVITY HP 30 4 MOTION VIEW ON 5 DEFAULT 6 RETURN RET 2 1 SELECT Select the areas which needs to be detected 4 areas are selectable 2 2 DISPLAY Display the selected area Position and area can be set in 2 1 2 3 SENSITIVITY The sensitivity to detect whenever object moves The lower value gets the higher sensitivity 2 4 MOTION VIEW Mark specific area to identify the moving object 2 5 DEFAULT Return to default setting 2 6 RETURN Return to last page 3 LANGUAGES 16 languages are selectable 4 DEFFECT Dead Pixel compensation 20 DEFECT LLVE DPC AUTO 2 STATIC DPC ON A 3 RETURN RET 4 1 LIVE DPC Dead Pixel Correction Correct the live dead pixel during preview LIVE DPC A LEVEL HII BO 2 RETURN RET 4 2 1 LEVEL Set the threshold value to judge if it needs RETURN Return to last page 4 2 STATIC DPC Static Dead Pixel Correction scan and find the dead pixel then save the position for correction Note Please do not change this setting 1 START l Z LEVELE HINTS 3 SENS UP x 8 4 AGC HIS 5 RETURN RET
17. will cause internal condensation inside the machine Please put the device inside the protection bag or handbag to prevent temperature shock and avoid using the device in an environment with extreme temperatures 2 1 3 Avoid dropping the device may malfunction if it encounters strong collision vibration or distortion 2 1 4 Turn the microscope off before cutting off the power supply do not forced cut off the power supply 2 1 5 Do not face the lens against strong light or sunshine for extended periods of time Strong light rays may degrade sensitive elements and generate white stains on images 2 1 6 Handle the device carefully do not disassemble cables forcefully and avoid contact with the lens since they are subjected to damage 2 1 7 Make sure to switch the power supply off and unplug the power cable if the device is not in operation for an extended period of time Store the device ina dry environment with excellent ventilation Do not expose the machine in an environment lower than 52C or higher than 502C 2 1 8 While carrying put the device inside the box to prevent from being damaged 32 2 2 Product Specification CMOS Sensor 2 million pixels CMOS sensor Object lens 4X 40 10 160 0 17 Lens Object lens 10X 10 0 25 160 0 17 NE E AA Object lens 4X 12x 130x 1 Object lens 4X 8 210x 460x on 21 5 monitor White LED x 30pcs Adaptor DC Input HDMI port Output 1080P 1920 1080 Pixel image Adaptor Power supplier Output
Download Pdf Manuals
Related Search