user guide - Smart-e
Contents
1.2. x x Pt T co 27 RS232 SM LED IR Emitter SM EYE IR Receiver Stereo Audio Output 1 Stereo Audio Output 2 Digital Audio Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX212SP D 3 Adjusting Equalisation and Contrast 3 1 To adjust equalization the pot labelled as EG may be rotated clockwise start by turning the pot completely ANTI clockwise and then slowly turn clockwise until equalization is correct As cable length increases the pot will need to be turned further clockwise To adjust contrast Gain as with equalization begin by turning the pot completely ANTI clockwise and slowly turn the pot clockwise until the desired image contrast Gain is displayed 4 Skew error compensation The SLX RX212 has built in delay lines to compensate for skew error in longer cable lengths Each video colour can be delayed up to 62ns which can be adjusted and set using the 3 buttons on the base of the unit 4 1 Press buttons INC and DEC together to enter the setting mode 4 2 Press button SET to select the colour to be delayed i e red green blue 4 3 Press the INC button to increase and DEC button to decrease the delay 44 Press buttons INC and DEC together to save the settings 4 5 Pressing buttons DE
3. MOUNTING HOLES ae 24 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX212 D SLX RX212SP D The SLX RX212 allows for the Long Range reception of UXGA RGsB YPrPb YUV Y C CVBS Stereo Audio and Infra Red or RS232 control signals when broadcasted along a single Cat5 UTP cable from a Smart e transmitter or matrix The signals are received along the Cat5 from the transmitter and then distributed as a Dual Screen output to the displays and control equipment via the appropriate connections and to speakers via a 3 5 mm mini jack 25 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628284 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX212SP D 1 Connecting SLX RX212 to the display device 1 1 Making sure that the Cat 5 cable is connected to the transmitter output connect the cable to the RJ45 socket on the receiver unit 1 2 If the cable connection is correct the power LED on the front of the receiver should illuminate power is sent up the Cat 5 cable 1 3 Connect the displays to the relevant connectors on the receiver see diagram below using the appropriate cable 1 4 If RS232 control is required then connect to the display via the 3 5mm minijack on the receiver using a C
4. 77 48X32 AV solution for marine environments also available SMW 16x16 and SMW 96x96 for more information visit our website or talk to one of our technical team tel 44 0 1306 628264 www smart e co uk S mart e Notice The information contained in this document is subject to change without notice Smart e makes no warranty of any kind with regard to this material including but not limited to implied warranties of merchantability and fitness for particular purpose Smart e will not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this material No part of this document may be photocopied reproduced or translated into another language without prior written consent from Smart e UK Ltd Edition 2 September 2008 Copyright 2008 Smart e UK Ltd Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Table of Contents Introducing SmartNet What s in the box What is SmartNet Why is SmartNet necessary How does SmartNet work Installation and Operation Transmitter Receiver Options Appendix Specifications Troubleshooting Limited warranty statement Partial Product List Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 5NA T 44 0 1306 628264 F 44 0 1306 628074 E info smar
5. SLX RX1 11 2 Connecting SLX RX1 11 to audio and Infra Red control 2 1 Connect the speakers or audio input on the display to the audio output on the receiver using a 3 5mm jack plug 2 2 If using the receiver to transmit Infra Red signals back down the cable to the transmitter unit then connect an eye to the jack position as shown in the diagram below If using the receiver to transmit Infra Red signals up to the display from the transmitter unit then connect a LED to the jack position as shown in the diagram below Please note connecting the IR eye will prevent the return RS232 path from the display Cat5 from Transmitter Matrix PSU connection is not required unit is RS232 powered from the mitter SM LED IR Emitter CEC Keng SM EYE IR Receiver 17 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX1 11 inti The receiver unit can compensate for cable losses over a length of 20 100m and for mounting purposes the unit is provided with two mounting hole points for fixing to the wall or screen See diagram below Simply hold receiver in place mark position of holes and set screws in these locations NB Always use screws with heads larger than the holes n MOUNTING HOLES As lt gt 4 4N 09 9 HeWS MMM IOIOI jr X Spmaart e
6. Operations outside product specifications c Mechanical abuse and exposure to severe conditions If Smart e receives during applicable warranty period notice of defect Smart e will at its discretion replace or repair defective product If Smart e is unable to replace or repair defective product covered by the Smart e warranty within reasonable period of time Smart e shall refund the cost of the product Smart e shall have no obligation to repair replace or refund unit until customer returns defective product to Smart e Any replacement product could be new or like new provided that it has functionality at least equal to that of the product being replaced Smart e warranty is valid in any country where the covered product is distributed by Smart e B Limitations of warranty TO THE EXTENT ALLOWED BY LOCAL LAW NEITHER SMART E NOT ITS THIRD PARTY SUPPLIERS MAKE ANY OTHER WARRANTY OR CONDITION OF ANY KIND WHETHER EXPRESSED OR IMPLIED WITH RESPECT TO THE SMART E PRODUCT AND SPECIFICALLY DISCLAIM IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY SATISFACTORY QUALITY AND FITNESS FOR A PARTICULAR PURPOSE C Limitations of liability To the extent allowed by local law the remedies provided in this warranty statement are the customers sole and exclusive remedies TO THE EXTENT ALLOWED BY LOCAL LAW EXCEPT FOR THE OBLIGATIONS SPECIFICALLY SET FORTH IN THIS WARRANTY STATEMENT IN NO EVENT WILL SMART E OR ITS THIRD PARTY SUPPLIERS BE
7. SLX RX111 Multi format Video Stereo Audio IR RS232 Inline Power Receiver Unit C C LU GN lt eg ICH made in uk MOUNTING HOLES ee 18 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628284 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX2 1 1 SLX RX211 The SLX RX21 1 allows for the Long Range reception of UXGA RGsB RGBS YPrPb YUV Y C CVBS Stereo Audio and Infra Red or RS232 control signals when broadcasted along a single Cat5 UTP cable from a Smart e transmitter or matrix The signals are received along the Cat5 from the transmitter and then distributed to the display and control equipment via the appropriate connection and to speakers via a 3 5 mm mini jack 19 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 DNA T 44 0 1306 628264 F 44 0 1306 828074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX2 1 1 1 Connecting SLX HX21 1 to the display device 4 1 Making sure that the Cat 5 cable is connected to the transmitter output connect the cable to the RJ45 socket on the receiver unit 1 8 If the cable connection is correct the power LED on the front of the receiver should illuminate power is sent up the Cat 5 cable 4 3 Connect the display to relevant connector on the receiver see diagram below using the appropriate cable 1 4 I
8. RS232 up to 115kbaud full duplex tx rx RS422 9600baud Connector Matrix Control RJ45 Voltage Frequency 90 230V 50 60Hz Connector IEC Mains Lead Fuse Rating Height BU 356mm 9U 400mm Inc PSU Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628284 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Technical Information SLX RX100 Video input Signal Type Connector UXGA YUV YPbPr YC CVBS RJ45 Bandwidth 400MHz Impedance Signal Type Bandwidth eOkHz OdB Impedance 10k Ohm Connector Signal Type Connector UXGA YUV YPbPr YC CVBS HD15 Bandwidth 4DOMHz Impedance 75 Ohm Signal Type Stereo Audio Bandwidth eO0kHz OdB Impedance 100 Ohm Connector 3 x 3 5mm mini jacks Female Requirement Connector 24VDC 500mA 5mm x 2 1mm 34 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628284 F 44 0 1306 828074 E info smart e co uk W www smart e co uk Technical Information Signal Type Connector Bandwidth Impedance Audio Inps Signal Type Bandwidt Impedance Connector Signal Type Connector Bandwidth Impedance Signal Type Bandwidt Impedance Connector Signal Type Connector Signal Type Connector Signal Type Connector Signal Type Connector Smart e UK Ltd e Hale SLX RX111 UXGA RGBS YUV YPbP
9. over a length of 20 100m and for mounting purposes the unit is provided with two mounting hole points for fixing to the wall or screen See diagram below Simply hold receiver in place mark position of holes and set screws in these locations NB Always use screws with heads larger than the holes m MOUNTING HOLES CL eXSHrX IS S e 4 ND Oe UEUUIS MMM CABLE COMPENSATION DEC 6 S E INC 6db Format 2 HD15 RGB SET CONTRAST CONTROL Wun Jeneoes Jeog OUI UI ZETSY MI oipny oeJejS oeprA 1euuoj niniw VGA YPbPr Sie Format R Both HD15s g ICH EQ 7 Gw ei made in uk MOUNTING HOLES ii 32 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA F 44 0 1306 628074 E info smart e co uk W www smart e co uk Technical Information SNX A8x32 Video Input 0 Signal Type UXGA RGBS YUV YPbPr YC CVBS Bandwidth 400MHz Impedance Connector Analogue Signal Type Stereo Audio Bandwidth 20kHz OdB Impedance 10k Ohm Analogue Audio Connector 48 x 2 RCA Female Digital Audio Connector 48 x 1 RCA Female Signal Type UXGA RGBS YUV YPbPr YC CVBS Bandwidth 400MHz Impedance 100 Ohm Connector 32 x RJ45 Signal Type Stereo Audio Bandwidth 20kHz OdB Impedance 100 Ohm Connector 32 x RJ45 Signal Type 30 500kHz modulated IR Connector de x RJ45 Signal Type 30 500kHz modulated IR Connector D15 to IR Blaster Signal Type
10. 74 E info smart e co uk W www smart e co uk Technical Information SLX RX212 D Video Input Signal Type Connector UXGA YUV YPbPr YC CVBS RJ45 Bandwidth 400MHz Impedance a 79 Ohm Audio Input 0 Analogue Signal Type Stereo Audio Digital Signal Type Digital Surround Sound Dolby DTS Bandwidth 2OkHz OdB Impedance 10k Ohm Connector Signal Type Connector UXGA YUV YPbPr YC CVBS 2 x HD15 RJ45 on SLX RX212D Bandwidth 400MHz Impedance Audio Outpt Analogue Signal Type Stereo Audio Digital Signal Type Digital Surround Sound Dolby DTS Bandwidth 20kHz OdB mpedance 100 Ohm Analogue Connectors dx 3 5mm minijacks Female RJ45 on SLX RX2 12D Digital Connector 1 x RCA Female 30 500kHz modulated IR 3 5mm mini jack Female 30 500kHz modulated 3 5mm mini jack Fema RS232 up to 115kbaud full duplex tx rx R5422 9600baud 3 5mm minijack Female RS232 up to 115kbaud full duplex tx rx RS422 9600baud 3 5mm mini jack Female 24VDC 500mA 5mm x 2 1mm 120x 94x26 mm 0 2kg 37 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Troubleshooting No video 1 Are the green LEDs on both the transmitter and receiver units If not check that the 24V power supply PSU is connected and the LED on the PSU is l
11. AB J19 1M The 24V PSU should be connected to the 2 5mm Female DC Jack adjacent to the RJ45 socket then plug the PSU into the Mains using the cable provided 24V PSU To Mains Cat5 from Transmitter Matrix nu C ez AA amp e VIDEO 2 RGBHV YPrPb VIDEO 4 CVBS etc RGBHV YPrPb CVBS etc 26 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628264 F 44 0 1308 828074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX212SP D 2 Connecting SLX RX212 to audio and Infra Red control 2 1 Connect the speakers or audio inputs on the displays to the audio outputs on the receiver using 3 5mm stereo mini jack cables 2 2 Connect the digital audio inputs on your display or amplifier to the digital audio output on the receiver using a standard RCA coaxial cable 2 3 If using the receiver to transmit Infra Red signals back down the cable to the transmitter unit then connect an eye to the jack position as shown in the diagram below If using the receiver to transmit Infra Red signals up to the display from the transmitter unit then connect a LED to the jack position as shown in the diagram below To connect RS232 use a 3 5mm mini jack plug to DY cable can be supplied by Smart e For female D9 CAB JDF 1M For male D9 CAB JDM 1M 24V PSU To Mains Cat5 from Transmitter Matrix n S EE eet wc e EP CUA VES
12. C and SET together will reset all delays to zero Note Although all 3 colours can be delayed it is usually only necessary to delay 2 of the colours to achieve skew error compensation Dach asi S lt gt 4 EINEN DTN MMM INC CABLE COMPENSATION DEC XS 6db ZLEXY XIS 9 EWS SET CONTRAST CONTROL YUN JeAie263 Jeu BUI UI ZEZTSY MI oIpny 08J9 S o9pIA 1euuo nni VGA YPbPr Gef ll Q5 made in uk Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk In this example the Green is under equalized and the Hed is slightly over equalized Skew error test signal In this example colours are in alignment and hence correctly equalized Skew error test signal Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 DNA 44 0 1306 628264 44 0 1306 628074 info smart e co uk www smart e co uk Installation and Operation SLX RX2 12SP D 5 Setting the jumpers on the Receiver 5 1 On the SLX RX212 you are able to select the format of video outputted by the HD15s by altering the jumpers on the base of the unit shown in the diagram below Aro pq fe e 4 n 02 9 i amp UIS MAM H INC CABLE COMPENSATION E n N o SUN RN DEC d CL eXH X S ei 6db SET CONTRAST CONTROL HUN 13413999Y Je 0g el MI oipny oeiejg oeplA ewu VGA YPbPr
13. IDEO TYPE SELECTION CONTRAST CONTROL x x kel o E E d E CABLE COMPENSATION made in uk Contrast control adjusts signal gain Cable compensation adjusts all three Colours together from 0 to 300m Model SLX RX100 13 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX100 3 Sync Processing For VGA applications the Transmitter adds the Horizontal and Vertical Sync Pulses to the Blue and Red channels However since the unit has been designed for use with other types of video the Receiver provides the ability to pass both the Red and Blue channels transparently or process them to remove the Sync Pulses lt Q gt O Green e Red O O O Blue 3 1 For composite y c and Y P P component the jumpers must be set in the Video position 3 2 For VGA the jumpers must be set in the VGA position The example below shows the jumpers set for composite s video or component lt 0 2 ed Blue 14 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 5NA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX1 11 SLX RX111 The SLX RX111 allows for the Short Range reception of UXGA RGsB RGBS YPrPb YUV and Long Range reception of Y C CVBS Stereo Audio and Inf
14. LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES WHETHER BASED ON CONTRACT TORT OR ANY OTHER LEGAL THEORY AND WHETHER ADVISED OF THE POSSIBILITY OF SUCH DAMAGES D Local law To the extent that this warranty statement is inconsistent with local law this warranty statement shall be considered modified to be consistent with such law 39 Product Range SmartLynx X SmartLynx X SmartCast System SmartNet X Matrix Switches SmartNet X Matrix Bundles Partial Product List Product Code SCX TX600 SCX TX550 TUSC 1042 SOX TX120E SOX TX550E SLX RX100ES SNX 8x8 SNX 16x16 SNX 8X8IRP SNX 8X8RSP Description Transmitter and Receiver Pair Transmitter and Receiver Pair Transmitter and Receiver Pair with RS232 1R Transmitter and Receiver Pair with RS232 1R Dual Transmitter and Receiver Pair with RS232 IR One to Six Transmitter Unit One to Five Transmitter Unit with RS232 1R SmartCast Eurocard Rack Up to 16 cards Dual Screen Transmitter Eurocard One to Five Transmitter Eurocard with RS232 IR Eurocard Receiver for UGXA YUV Y C and Audio 8 x 8 Distribution Matrix 16 x 16 Distribution Matrix Up to 256 x 256 Complete Infrared Controlled 8X8 Matrix Package Complete RS232 Controlled 8X8 Matrix Package Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 DNA T 44 0 1306 628284 F 44 0 1306 628074 E info smart e co uk W www smart e co uk
15. LX RX100 1 Connecting SLX RX100 to the display device 4 1 Making sure that the Cat 5 cable is connected to the matrix transmitter output connect the cable to the RJ45 socket on the receiver unit If the cable connection is correct the power LED on the front of the receiver should illuminate power is sent up the Cat 5 cable Connect the display to relevant connector on the receiver see diagram below using the appropriate cable Cat5 from f Transmitter Matrix PSU connection is not required unit is powered from the Cat5 cable Speakers Monitor 12 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 5NA T 44 0 1306 628284 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX100 The Receiver unit is preset for approximately 50m which is sufficiently accurate for most applications However if the image does not look sharp enough then follow the instructions below 2 1 Whilst looking at an image on the display preferably a long horizontal bar adjust the CABLE COMPENSATION dial 2 2 Looking at the right hand edge of the bar you will see the image change A highlighting bright edge means over compensation whilst a blurred dark edge means under compensation 2 3 Adjust the dial until both effect are neutralized The Contrast control dial is factory pre set and usually needs no adjustment UXGA Stereo Audio Line Power Receiver Unit V
16. M cable supplied to the topmost Comms In RJ45 on the front of the matrix 4 2 Connect the D9 end of the CAB R19 1M to either of the supplied serial converters 4 3 For a control system with a D9 port use the AL 300 4 4 For a control system with a USB port use the AL 310 4 5 Finally connect the chosen serial converter to your control system using the applicable standard cable USB or D9 To Control System D9 port To Control System USB port Top Comms OUT of Upper Module connects to Top Comms IN of Lower Module 6 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation 5 Connecting the Power Supplies 5 1 On the rear panel of the unit using the cables supplied link the Canon connector marked PSU 1 to the corresponding connector also marked PSU 1 on the Power supply directly below it Then connect the two Canon connectors marked PSU 2 in the same fashion as above see diagram below y Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628284 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation 6 System Power up 6 1 Turn the system on by plugging in the power adapter to the SmartLynx if they are not yet connected See diagram opposite Power up your computer Observe both tra
17. co uk W www smart e co uk Installation and Operation SLX RX2 1 1 3 Adjusting Cable Compensation Equalization and Contrast Control 3 1 To adjust equalization the pot labelled as Cable Compensation may be rotated clockwise start by turning the pot completely ANTI clockwise and then slowly turn clockwise until equalization is correct As cable length increases the pot will need to be turned further clockwise The Contrast Control adjustment Gain is factory set at OdB Leave at preset unless you require to compensate for another piece of equipment in the chain i e old display which has lost brightness 4 Skew error compensation The SLX RX211 has built in delay lines to compensate for skew errors in longer cable lengths of Cat6 cable Each video colour can be delayed up to G2ns which can be adjusted and set using the 3 buttons on the base of the unit 4 1 Press buttons INC and DEC together to enter the setting mode 4 2 Press button SET to select the colour to be delayed i e red green blue indicated by the respective LED 4 3 Choose the most delayed colour the one which is to the right of the other colours and delay the other 2 colours to that position 4 4 Press the INC button to increase and DEC button to decrease the delay 4 5 Press buttons INC and DEC together to save the settings 46 Pressing buttons DEC and SET together will reset all delays to zero No
18. f RS232 control is required then connect to the display via the 3 5mm minijack on the receiver using a CAB J19 1M Cat5 from Transmitter Matrix PSU connection is not required unit is powered from the C Cat5 cable soneyz ces NE pm onam Component YPbPr S Video Y C UXGA RGBHV Scart RGBS or Composite 20 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX2 1 1 2 Connecting SLX RX21 1 to audio and Infra Red control 2 1 Connect the speakers or audio input on the display to the audio output on the receiver using a 3 5mm jack plug 2 2 If using the receiver to transmit Infra Red signals back down the cable to the transmitter unit then connect an eye to the jack position as shown in the diagram below If using the receiver to transmit Infra Red signals up to the display from the transmitter unit then connect a LED to the jack position as shown in the diagram below Please note connecting the IR eye will prevent the return RS232 path from the display Cat5 from Transmitter Matrix PSU connection is not required unit is RS232 powered from the SM LED IR Emitter Cat5 cable SM EYE IR Receiver 2 1 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 DNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e
19. ine equalization and compensation p Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628264 F 44 0 1306 828074 E info smart e co uk W www smart e co uk Installation and Operation 1 Preparing for installation Start installation process by ensuring that all video displays and audio devices are compatible with the computers being used This is accomplished by connecting the devices directly to the computer and checking that the devices operate as desired without the SmartNet system Stereo Analogue Optional Infra Red Receiver Eye SLX RX212 Cat5 to Receivers d Digital Audio Amplifier Monitor 2 Optional VI Monitor 1 SLX RX111 Monitor Install CAT 5 wiring between desired locations In order to minimize system operation difficulties avoid routing the system cables near fluorescent lights air conditioners or machines that may create electrical noise 3 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation 2 Connect Transmitter to the signal sources and Matrix 2 1 Connect the video output of the source device to the input of the matrix using the applicable interface cable if relevant 2 2 Connect the audio output of the source device to the audio input of the matrix using the appropriate cable 2 3 Co
20. it Check the cable compensation dials on the underside of the unit Over compensation of the Red and Blue channels can cause the display to misinterpret the sync pulses and not display an image 2 Is the video source a laptop or floating a floating source is one which has no earth reference i e uses a double insulated PSU or a figure 8 mains cable If so make sure the PSU is an earthed unit when not using the PSU supplied 3 Is the audio input level too high The audio level should be set to line level OdB or 700mV peak to peak to prevent interference Display has problems syncing 1 Is the audio input level too high The audio level should be set to line level OdB or 700mV peak to peak to prevent interference 38 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628284 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Appendix Limited Warranty Statement A Extent of limited warranty 1 Smart e UK Ltd warrants to the end user customers that Smart e product specified above will be free from defects in materials and workmanship for the duration of 3 years which duration begins on the date of purchase by the customer Customer is responsible for maintaining proof of date of purchase Smart e warranty covers only those defects which arise as a result of normal use of the product and do not apply to any a Improper or inadequate maintenance or modifications b
21. mul Format R oth HD15s g B uf el made in uk Viewed from underside of board where the pots reside Video on Second HD15 Video on Both HD15s Red Green Blue Oo Q RAO O O BleeO 0O O L1 l For YPrPb O OO 30 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628264 F 44 0 1306 828074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX2 12D 6 How to Cascade the SLX RX212D 6 1 As well as having all the functions of the regular SLX RX212 the SXL RX212D also has the ability to be cascaded for up to 5 units 6 2 In order to cascade the SLX RX212Ds Cat5 cable should be used to join together the supplementary units with the Cat5 output on the first unit to be joined to the Cat input on the second unit etc See diagram below All additional SLX RX212Ds connected after the initial unit MUST have their own power supply units attached DC24V 20W PSU SLX RX212D Cascading Cat 5 cable m E from Smart e Cat 5 cable Cat 5 cable transmitter To next SLX RX212D To next SLX RX212D 6 4 All SLX RX2 12Ds then connect to display and audio equipment as shown for the standard unit on the previous pages 31 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk 12SP D The receiver unit can compensate for cable losses
22. n of the SLX RX10OO see page SLX RX1 11 UXGA RGBS RGsB YPrPb Y C CVBS Stereo Audio and R8232 or Infra Red control option For Instructions on Installation of the SLX RX11 1 see page SLX RX21 1 Same as SLX RX111 but with greater range and skew compensation For Instructions on Installation of the SLX RX211 see page 9 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 5NA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Receiver Options SLX RX212SP D Dual Screen Output UXGA RGsB YPrPb Y C CVBS and Stereo Audio with RS232 or Infra Red control option SLX RX21 2D can be cascaded For Instructions on Installation of the SLX RX212 see 1Q Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628284 F 44 0 1306 828074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX100 SLX RX100 The SLX RX100 allows for the reception of UXGA RGsB YPrPb YUV Y C CVBS and stereo audio when broadcasted along a single Cat5 UTP cable from a Smart e transmitter or matrix The unit then distributes the received signal to a display via a HD15 connection and to speakers via a 3 5mm mini jack 11 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 DNA T 44 0 1306 628264 F 44 0 1306 828074 E info smart e co uk W www smart e co uk Installation and Operation S
23. nnect the digital audio output of the source device to the digital audio input using a standard RCA cable Digital audio Input number should correspond to that used for Video from the same source If using RS232 or Infra Red see installation details on the following pages Stereo Audio Digital d Audio Blu Ray DVD Player YPrPb 4 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 5NA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation 3 Connecting the Infra Red Blaster for Source Device control 3 1 Using the IR Blaster control cable attach one end into the IR control port on the rear of the SNX 48x32 and the other end to the rear of the 1U Blaster unit 3 2 Then plug the IR emitter LED into the relevant 3 5mm jack socket on the front of the Blaster unit and position the LED at the device to be controlled Making sure that the Blaster port number corresponds to the video input number on the SNX 48x32 3 3 See IR output 1 on the Blaster corresponding to video input 1 on the Matrix in the diagram below Blu Ray DVD Player YPrPb Input 1 SM LED IR Emitter 5 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation 4 Controlling the switch with R5232 4 1 Connect the CAB R19 1
24. nsmitter and receiver power LED are ON and source device is switched on 7 Preparing and connecting System CAT 5 cable The SmartLynx utilizes category 5 CAT 5 unshielded twisted pair UTP cable to transport signal between transmitter and receiver CAT 5 cable is more desirable than coaxial cable due to its low cost and ease of installation This cable is used for LAN applications and is found in abundance already installed in many buildings The category 5 is a standard which establishes minimum requirements for telecommunications cabling within a commercial building The standard covers various aspects of wiring including telecommunications outlets Following is the wiring standard for terminating CAT 5 cable using HJ 45 connector Pins 1 amp 2 u ninin Pins 3 amp 6 Pins4 amp 5 P 12345678 Pins 7 amp 8 Connectors RJ 45 Capacitance 14 pf ft 46 2 pf m Conductor Gauge 24 AWG Impedance 100 15 ohms 4 Pair 8 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Receiver Options 8 SmartLynx Receiver Options There are a number of different receiver options available to accompany the matrix please check the model number and relevant page number reference below SLX RX1 00 a NE P d UXGA RGsB YPrPb Y C CVBS and Stereo Audio For Instructions on Installatio
25. r YC CVBS RU45 400MHz Stereo Audio 20kHz OdB 10k Ohm UXGA HD15 RGBS YUV 3xRCA YC 4pin minidin CVBS 400MHz Stereo Audio 20kHz OdB 100 Ohm 3 x 3 5mm mini jacks Female 30 500kHz modulated IR 3 5mm mini jack Female ated IR RS232 up to 115kbaud full duplex tx rx RS422 9600baud RS232 up to 115kbaud full duplex tx rx RS422 9600baud 3 5mm mini jack Female 24VDC 500mA 5mm x 8 1mm 35 House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Technical Information SLX RX2 11 Video input Signal Type Connector UXGA RGBS YUV YPbPr YC CVBS RJ45 Bandwidth 4DOMHz Impedance Ado Signal Type Stereo Audio Bandwidth eOkHz OdB Impedance 10k Ohm Connector Signal Type Connector UXGA HD1 5 RGBS YUV 3xRCA YC 4pin minidin CVBS Bandwidth 400MHz Impedance Signal Type Stereo Audio Bandwidth eO0kHz OdB Impedance 100 Ohm Connector 3 x 3 5mm mini jacks Female Signal 30 500kHz modulated IR 3 5mm mini jack Female 30 500kHz modulated IR RS232 up to 115kbaud full duplex tx rx RS422 9600baud RS232 up to 115kbaud full duplex tx rx RS422 9600baud 3 5mm mini jack Female e4VDC 500mA 5mm x 8 1mm 36 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RHS SNA T 44 0 1306 628284 F 44 0 1306 8280
26. r than commonly specified product limitations of 5m In this case several choices are available but most are expensive and bulky which is in some cases simply not practical due to space limitations in the conduits The SmartNet allows the transmission of AV signals over a standard Cat5 UTP cable over distances of up to 300m with full IR or RS232 control options The actual distance is a function of the signal resolution and cable quality The following is a rough guide to distance and resolution Cat5 Cable Length Maximum Recommended Resolution 200m UXGA 1600x1200 200m 1080p 1920x1080 300m SXGA 1280x1024 How does SmartNet work The Smart e SmartNet systems are switch transmitter and receiver pairs designed to extend video audio and IR RS232 signals over UTP amp STP unshielded amp shielded twisted pair category 5 Cat5 cabling They are supplied with a UK power supply and consist of a transmitter with a video input connectors vary by model an audio input and a Cat5 output and a receiver with a cato input and corresponding outputs Certain models are also supplied with looping cato outputs local outputs and or IR or H8232 connections The extended signals depend on the model but supported signals are UXGA CVBS YPbPr Y C RGsB and RGBS analogue format plus Stereo Analogue amp Digital Surround sound Audio The basic concept behind this product is the ability to encode and decode analogue signal combined with precise l
27. ra Red or HS232 control signals when broadcasted along a single Cat5 UTP cable from a Smart e transmitter or matrix The signals are received along the Cat5 from the transmitter and then distributed to the display and control equipment via the appropriate connection and to speakers via a 3 5 mm mini jack 15 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 DNA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation SLX RX1 11 1 Connecting SLX BX1 11 to the display device 1 1 Making sure that the Cat 5 cable is connected to the transmitter output connect the cable to the RJ45 socket on the receiver unit 1 8 If the cable connection is correct the power LED on the front of the receiver should illuminate power is sent up the Cat 5 cable 1 3 Connect the display to relevant connector on the receiver see diagram below using the appropriate cable 1 4 If R5232 control is required then connect to the display via the 3 5mm minijack on the receiver using a CAB J19 1M Cat5 from Transmitter Matrix PSU connection is not required unit is powered from the Leg Cat5 cable Component YPbPr S Video Y C UXGA RGBHV Scart RGBS or Composite 16 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 5NA T 44 0 1306 628264 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Installation and Operation
28. t e co uk W www smart e co uk Introducing SmartNet Cat5 AV Switch What s in the box Thank you for buying the Smart e SmartNet Cato AV Switch amp Extender Depending on the configuration of your system various quantities of the parts below may be included in your shipment If any of the accessories listed below are missing please contact the Smart e dealer you purchased products from or contact Smart e customer support at 44 0 1306 628264 If you ordered a SmartNet Cat5 Matrix Switch SNX 48x32 X BU 8U Inc PSU If you ordered SmartLynx Digital Audio Receivers E Digital Audio Cascade able SLX AX212 Cat5 oo nit SLX AX212D Cat5 uS nit 1 Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA T 44 0 1306 628284 F 44 0 1306 628074 E info smart e co uk W www smart e co uk Introducing SmartNet Cat5 AV Switch What is SmartNet The SmartNet systems are a combination of high quality video and audio Switches transmitter and receiver devices designed to transmit high resolution computer video and or audio signals over Cat5 wire AV stands for Audio Visual and includes such signal formats as Broadcast Video TV video signal Computer Video VGA SVGA SXGA and etc signals and various formats of Audio signals Why is SmartNet necessary Sometimes you may have numerous source devices to be displayable upon screens Or that AV signals need to be transmitted over distances greate
29. te Although all 3 colours can be delayed it is usually only necessary to delay 2 of the colours to achieve skew error compensation CONTRAST CONTROL ow g db W EQ LEDs rA a 9 u ew S ag a CAI LE COMPENSATION i eon Qe Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 DNA T 44 0 1306 628284 F 44 0 1306 628074 E info smart e co uk W www smart e co uk In this example the Red signal is most delayed and the Green signal the least delayed Skew error test signal In this example colours are in alignment and hence correctly equalized Skew error test signal Smart e UK Ltd e Hale House Barns e Oakwoodhill e Ockley e Surrey e RH5 SNA 44 0 1306 628264 44 0 1306 628074 info smart e co uk www smart e co uk Installation and Operation SLX RXe 1 1 The receiver unit can compensate for cable losses over a length of 20 100m and for mounting purposes the unit is provided with two mounting hole points for fixing to the wall or screen See diagram below Simply hold receiver in place mark position of holes and set screws in these locations NB Always use screws with heads larger than the holes ae MOUNTING HOLES LLEXY XIS m lt gt 4 NOS UEUUIS MAAN En CONTRAST i CONTROL 6db TO 6db o Ser CABLE COMPENSATION i i A Pas N az Dc N i Sg ERE a2 vs rol 9 0 ZS o 2G ao o ER lt Z BE c Se pong lt 9 IOl e
Download Pdf Manuals
Related Search