Casablanca 99055 Instructions / Assembly
Contents
1. screwdriver Remove the plug button Then follow the TYPE C ASSEMBLY INSTRUCTIONS on pages 8 9 MA007 01 07 26 13 L 1 888 830 1326 TYPE A ASSEMBLY INSTRUCTIONS Mounting Screw Partially install the two mounting screws into the bottom of the lower switch housing Using the single pin connectors connect the black or blue wire from the fan to the black wire from the light kit Connect the white wire from the fan to the white wire from the light kit Switch Housing If your fan does not have pin connectors on the wires coming from the switch housing install the wiring harness provided Using the provided wire connectors connect the white wire from the fan to the white wire from the wire harness and connect the black or blue wire from the fan to the black wire from the wire harness Mounting Lift the light kit up to meet the lower switch housing Wrap keyhole slots around the screws and twist counterclockwise Tighten screws Do not allow the light kit to hang only by the wire connections MA007 01 07 26 13 TYPE A ASSEMBLY INSTRUCTIONS CONTINUED Grommeted Pull Chain Hole After the light kit is mounted to the fan feed Installing the bulb Install a bulb into each the pull chains from the fan s switch housing of the sockets When necessary replace and the light kit through the grommeted with bulbs of the same type and wattage holes in the base of the light kit Extension chains are2. from the fan s of the sockets When necessary replace switch housing and the light kit through with bulbs of the same type and wattage the grommeted holes in the base of the light kit Extension chains are provided if necessary Both pull chains must line up with the grommeted holes to operate properly Installing the globe sold separately Position the Installing the Pull chain pendant indentations in the outer rim of the globe so that they Attach the pull chain pendant to the line up with the tabs on the inside surface of the light end of the short chains coming from the fixture rim Carefully lift the globe up inside the light switch housing and the light kit Turn fixture as far as it will go Rotate the globe in a clockwise direction until it is held tightly in place by the four tabs MA007 01 07 26 13 power on Your installation is complete L 1 888 830 1326 TROUBLESHOOTING Lights don t come on e Make sure that the bulbs are properly installed Make sure power switch is on Pull the pull chain to make sure it is on Check the circuit breaker to ensure the power is turned on Check the pin connections in the light kit Refer to the fan manual for locating the fan s wiring Verify that the light and power wires are correctly connected to the ceiling and the light kit ONE YEAR WARRANTY This product is warranted to the original purchaser by Casablanca Fan Company Hunter Fan Company aga
3. Decorative Low Profile Integrated Kit Installation Manual Models 99050 99051 99052 99053 99054 99055 Compatible with 2xxxx Types A Z 51000 58999 fan series 59500 59999 fan series Select Casablanca fans MA007 01 07 26 13 1 888 830 1326 BEFORE YOU BEGIN Read entire installation instructions carefully before beginning installation and save these instructions Switch Housing Your light kit is compatible with most ceiling fans The light kit will attach to the fan s switch housing Begin on page 3 where you will choose the type of switch housing that most closely resembles the one on your fan From there you will be directed to the set of assembly instructions that are appropriate for installing the light kit to your fan READ AND SAVE THESE INSTRUCTIONS This product conforms to UL Standard 507 AWARNINGS w 1 To reduce the risk of fire electrical shock or personal injury mount fan directly from building structure and or an outlet box marked acceptable for fan support of 70 Ibs 31 8 kg and use the mounting screws provided with the outlet box w 2 To avoid possible electrical shock before installing or servicing your fan disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location If you cannot lock the circuit breakers in the off position securely fasten a prominent warning device such as a tag to the service panel A CAU
4. TIONS c 1 All wiring must be in accordance with national and local electrical codes ANSI NFPA 70 If you are unfamiliar with wiring use a qualified electrician MA007 01 07 26 13 1 888 830 1326 WHICH ASSEMBLY METHOD WILL I USE Choose one of the four images below that most closely resembles the switch housing on your fan then follow the instructions under the image Housing Cap If your fan s switch housing cap resembles this one remove the cap screws with a Phillips head screwdriver Then follow the TYPE A ASSEMBLY INSTRUCTIONS on pages 4 5 NSS gt gt SS Z NDS py awh yk 3 Housing a Screw B If your fan s switch housing cap resembles this one remove the switch housing screws using a Phillips head screwdriver Then remove the plug button using a standard screwdriver Then follow the TYPE B ASSEMBLY INSTRUCTIONS on pages 6 7 Housing Cap If your fan s switch housing cap resembles this one remove the whole switch housing by removing the switch housing screws with a Phillips head screwdriver Remove the two cap screws from the inside of the switch housing Reinstall the switch housing Tighten the switch housing screws Then follow the TYPE A ASSEMBLY INSTRUCTIONS on pages 4 5 Switch Housing PI Screw ha If your fan s switch housing cap resembles this one remove the whole switch housing by removing the switch housing assembly screws with a Phillips head
5. connect the black or blue wire from the fan to the black wire from the wire harness Switch Housing Screw Lift the light kit assembly up so that the screw holes in the lower switch housing line up with the holes in the upper switch housing Install the switch housing screws and tighten securely Do not allow the light kit to hang only by the wire connections MA007 01 07 26 13 TYPE B ASSEMBLY INSTRUCTIONS CONTINUED Socket Grommeted Pull Chain Hole After the light kit is mounted to the fan feed Installing the bulb Install a bulb into each the pull chains from the fan s switch housing of the sockets When necessary replace and the light kit through the grommeted with bulbs of the same type and wattage holes in the base of the light kit Extension chains are provided if necessary Both pull chains must line up with the grommeted holes to operate properly Installing the globe sold separately Position the Installing the Pull chain pendant indentations in the outer rim of the globe so that they Attach the pull chain pendant to the line up with the tabs on the inside surface of the light end of the short chains coming from the fixture rim Carefully lift the globe up inside the light switch housing and the light kit Turn fixture as far as it will go Rotate the globe in a clockwise direction until it is held tightly in place by the four tabs MA007 01 07 26 13 power on Your installat
6. inst defects in material and workmanship for one 1 year from date of purchase During the warranty period we will repair or at our option replace a defective product at no charge For information on how to obtain service contact the Casablanca Hunter Service Department by calling our toll free number at 888 830 1326 Damage to the product caused by mishandling improper installation or modification is not covered by this warranty This warranty is given in lieu of all other warranties expressed or implied Some states do not allow limitations of time on an implied warranty therefore the above limitations may not apply in every case This warranty states specific legal rights which may vary from state to state If you have problems installing or operating your light kit do not return this product to the dealer Call our Consumer Affairs Hotline 888 830 1326 Monday through Friday 8 00 am to 4 30 pm Central 10 MA007 01 07 26 13
7. ion is complete 1 888 830 1326 TYPE C ASSEMBLY INSTRUCTIONS Switch Housing Connector If your fan does not have pin connectors on the wires coming from the switch housing install the wiring harness provided Using the provided wire connectors connect the white wire from the fan to the white wire from the wire harness and connect the black or blue wire from the fan to the black wire from the wire harness Lower Switch Housing Lift the lower switch housing up so that the screw holes line up with the holes in the upper switch housing Install the switch housing screws and tighten securely Feed the wires through the center hole in the switch housing Then using the single pin connectors connect the black or blue wire from the fan to the black wire from the light kit Connect the white wire from the fan to the white wire from the light kit Switch Housing Lift the light kit up tucking the wires into the hole in the switch housing Install the center stem of the light kit into the lower switch housing by turning the threaded rod clockwise into the threaded hole Continue turning until tight Do not allow the light kit to hang only by the wire connections MA007 01 07 26 13 TYPE C ASSEMBLY INSTRUCTIONS CONTINUED Socket Grommeted Pull Chain Hole After the light kit is mounted to the Installing the bulb Install a bulb into each fan feed the pull chains
8. provided if necessary Both pull chains must line up with the grommeted holes to operate properly Installing the globe sold separately Position the Installing the Pull chain pendant indentations in the outer rim of the globe so that they Attach the pull chain pendant to the line up with the tabs on the inside surface of the light end of the short chains coming from the fixture rim Carefully lift the globe up inside the light switch housing and the light kit Turn fixture as far as it will go Rotate the globe in a clockwise direction until it is held tightly in place by the four tabs MA007 01 07 26 13 power on Your installation is complete 1 888 830 1326 TYPE B ASSEMBLY INSTRUCTIONS Feed the wires through the center hole in the switch housing the washer and the nut Then install the switch housing by twisting clockwise onto the threaded rod Install the washer and nut onto threaded rod and tighten securely Using the single pin connectors connect the black or blue wire from the fan to the black wire from the light kit Connect the white wire from the fan to the white wire from the light kit Switch N Housing ire N N Connector N If your fan does not have pin connectors on the wires coming from the switch housing install the wiring harness provided Using the provided wire connectors connect the white wire from the fan to the white wire from the wire harness and
Download Pdf Manuals
Related Search