Sea Gull Lighting 47251-758 Installation Guide
Contents
1. INSTALLATION AND SAFETY INSTRUCTIONS CAP NUTS G OUTLET BOX WIRE CONNECTORS RETAINING RING B gt KEEA FIGURE 1 GROUNDING amp UNIVERSAL MOUNTING BAR LOCK UP UNIVERSAL MOUNTING BAR J OUTLET BOX GREEN SCREWS K GROUNDING SCREW L WIRE CONNECTOR Lo FIGURE 2 NOT SUPPLIED MOUNTING SCREWS I WARNING BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF EITHER THE FUSE REMOVED OR THE CIRCUIT BREAKER OFF GENERAL You don t need special tools to install this fixture Be sure to follow the steps in the order given Under no circumstances should a fixture be hung on house electrical wires nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system Read instructions carefully If you are unclear as to how to proceed consult a qualified electrician NOTE Proper wiring is essential for the safe operation of this fixture CANOPY F NOT SUPPLIED Carefully remove the fixture from the carton and check that all parts are included as shown in Figure 1 amp 2 Be careful not to misplace any of the screws or parts which are needed to install this fixture S60 gul ighting Installation And Safety Instruction HC 604 082203 Line art shown may not exactly match the fixture enclosed However the installation instructions do apply to this fixture Fill In Item Number On Carton And File This Sheet For Fixtu2. re Reference ITEM INSTALLATION HC 604 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET STEP 1 Insert fixture mounting screws I into threaded holes of universal mounting bar J Run screws all the way down to the heads STEP 2 Place universal mounting bar J against outlet box not supplied and screw in place using outlet box screws K not supplied Be sure the mounting screws are PERFECTLY VERTICAL so fixture hangs straight d O 2s STEP 3 A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below GROUP A CONNECT TO BLACK GROUP B CONNECT TO WHITE HOUSE WIRE HOUSE WIRE BLACK WHITE PARALLEL WIRE ROUND amp SMOOTH WHITE OR GREY WITH TRACER BROWN GOLD OR BLACK WITHOUT TRACER CON o O PARALLEL WIRE SQUARE amp RIDGED WHITE OR GREY WITHOUT TRACER BROWN GOLD OR BLACK WITH TRACER Se NOTE When parallel wire is used the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box Do Not twist wires together before using wire connectors C Fit a wire connector not supplied over the wires and screw the connector clock
3. tall glass A Secure with retaining ring B STEP 3 Install lamps CLEANING To clean wipe fixture with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abrasive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts All parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts
4. wise until you feel a firmness D Try gently to pull the connector off the wires If you can pull the connector off carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner STEP 4 GROUNDING INSTRUCTIONS The green grounding screw L is to be inserted into the hole with two raised dimples provided on the universal mounting bar J Wrap the ground wire from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw L on the universal mounting bar J If uninsulated ground wire is on the universal mounting bar connect the ground wire from the fixture if supplied and the outlet box to it using a small wire connector not supplied See Figure 2 NOTE Underwriters Laboratories U L does not require all fixtures to have ground wires These fixtures still meet all U L specifications The listing mark of Underwriters on the product identifies products manufactured under its listing and Follow Up Service Programs NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 1 After wires are connected tuck them carefully inside the outlet box Position canopy F over mounting screws I and secure in place with cap nuts G STEP 2 Ins
Download Pdf Manuals
Related Search