King Canopy HC1020PCSL Instructions / Assembly
Contents
1. Hercules Snow Load 10ft X 20ft 10ft8in Wide x 20ft Deep x 6ft8in Side Height 9ft6in Center Height King Canopy Item HC1020PCSL With 8 Legs Cable Truss System Cover 4 Piece Zippered Side Wall Kit 2 Side Panels with Windows Rear Solid Panel and 1 Front Panel with Zippers WARNING Keep all flame and heat sources away from this tent fabric Meets the flammability requirements of Distributed by l CPAI 84 Section 6 and NFPA 701 l PIC America LTD It is not fire proof The fabric will burn if 1730 Five Points Lane Fuquay Varina NC 27526 setolnicantauous comiackyivi any flame source 1 800 800 6296 gt www kingcanopy com PARTS LIST 6X6 2PC 6x6 15PC 5X8 2PC 3W215PC 4W215PC BALLW 100 PFOOT2 PTCL1020FR6 T81020SWW W T81020EWZFR6 T81020EWFR6 PTCL1020VS SL1020C 8 pc 9pc 8 pc 6 pc 6 pc 100 pc 8 pc 1 pc 2 pc 1 pc 1 pc 1 pc 1 pc 78in pipes 2in diameter 78in pipes 1 1 2in diameter 68in pipes 2in diameter 3 way connectors 4 way connectors Elastic ball straps Foot pads Cover Sidewalls with windows Front wall with zippers End wall solid Valance tie downs 4 pack Four Snow Load Truss Cables FRAME ASSEMBLY Step 1 Separate all pieces according to size and shape and arrange per the illustration shown below a2 la E 68 68 68 68 78 I 78 78 78 68 68 682. 68 Set aside eight 78 pipes to use for legs 78 ee a 78 qp 2 78 Please note e The 68in 2 in diameter pipes are used to form the roof rafters e The 78in 1 1 2 in diameter pipes are used to form the roof perimeter e The 78in 2 in diameter pipes are used to form the legs of the unit Step 2 As you are assembling the pipes of this unit you will also need to begin installation of the Cable Truss System To do so place the large center loops of the Cable Truss System over each rafter peak 3 way connector and then attach rafter pipes to each connector With the rafter pipes and attached cable truss system lying on the ground the small outer loops should be slipped over each piece of 78in 1 1 2in diameter pipe Attach 3 way connectors at each end of the pipe and center the truss cable Repeat on opposite side of the roof perimeter and for each of the perimeter pipes Step 3 Connect the remaining perimeter and rafter pipes together starting with the center of the frame keeping the cable truss system centered on each section DO NOT CONNECT LEG POLES AT THIS POINT COVER ASSEMBLY Step 1 Unfold the cover with the grommets toward the cover s bottom and place over the frame The flared edges should be located at each of the 4 corners of the frame Step 2 Begin attaching the cover with the elastic ball straps by inserting the elastic cord of the ball strap underneath the cover and through the grommet Then
3. cable or rope through the eye of the anchor and pull tight Step 4 Now continue to screw each anchor into the ground until the eye of the anchor is flush with the ground This will secure the anchor rope even tighter NOTE You should check and tighten the rope frequently to ensure maximum stability of your canopy and to protect against wind damage ROOF PIPE z FITTING 3 or 4 way LEG PIPE IMPORTANT NOTICE PLEASE READ CAREFULLY Weare confident that you will be completely satisfied with your King Canopy unit Please take a moment to read the very important information below and call us with any questions you may have King Canopy PIC America LTD has no control over wind snow ice rain or any other weather condition and we are in no way responsible for any damage caused by the canopy or to the canopy We suggest you contact your insurance carrier just as you would for any other outside structure OTHER PRECAUTIONS WHICH MUST BE FOLLOWED Keep all flame and heat sources away from this tent fabric The tent fabric will burn if left in continuous contact with any flame source DO NOT cook underneath or near canopy DO NOT store or use flammable liquids underneath or near canopy DO NOT ignite or store fireworks underneath or near canopy DO NOT use bleach to clean cover DO NOT dry clean cover DO NOT wash cover in washing machine or dry in dryer Hand wash with mild soap and water only DO NOT allow rain water sn
4. eplacement If you know strong weather is predicted remove the cover or take down the canopy unit completely The cover is designed to be quickly and easily removed Warranty All components of this canopy feature a 1 year limited warranty and are warranted to be free from defects in material and workmanship for a period of 1 year You must complete and return the enclosed warranty card promptly after purchase Please retain your proof of purchase receipt you will be asked to provide this receipt in order to obtain warranty service Non Warranty Replacement Parts If after expiration of the warranty period you require replacement parts please contact us at 1 800 800 6296 We stock replacement parts and make them available to you at discounted prices Our customer service department will be pleased to assist you in any way possible Certain regions of the country are extremely hard on covers of any kind Normal wear and tear is not covered under the warranty and should be expected In order to receive a discounted or free replacement part you may be asked to return the part freight prepaid to our warehouse for inspection before we will send a replacement You must in all cases provide a copy of your receipt showing the date of purchase model number and price For missing parts replacement parts or any questions Please Call 8 00am 5 00pm EST Monday Friday 1 800 800 6296 or 1 919 552 2977 Or you can fax us at 1 919 552 5069 R
5. eplacement parts and customer service is also available through our website Please visit us at www kingcanopy com
6. ow or ice to accumulate on top of cover DO NOT hang or suspend anything from the frame grommets truss system or ball straps of the unit REMOVE canopy cover before a storm or disassemble entire canopy unit if possible REMOVE rain water snow and ice from canopy cover This is a temporary structure and is not recommended for use as a permanent structure PRODUCT INFORMATION Defective Parts We try our best to eliminate any defective parts that are shipped with our products If however you should find a defective part we will replace free of charge any part which is defective You will need to provide proof of purchase showing date of purchase and provide us with detailed description of the defective component Your replacement will be shipped by ground shipping freight prepaid Next day or express shipping will require freight collect and paid for by you the consumer Damages from improper anchoring strong winds snow ice or rain are not considered defects Improper Anchoring Strong Winds Rain Snow or Ice King Canopy PIC America LTD does not guarantee these canopies under strong weather conditions These canopies are designed to protect against damages caused by sun rain tree sap birds etc They are not designed to hold roof loads that accompany snow ice or heavy rains If your canopy is not anchored securely it can be lifted by the wind and will fly away If your canopy takes flight we are not responsible for any r
7. ps located at the bottom of each leg skirt over the flanged clip on the foot pads FINISH ASSEMBLY OF YOUR CANOPY To complete the assembly and securing of your unit finish installing elastic ball straps completely around the unit at the top and bottom wherever there is a grommet Ball straps at the bottom of each side panel should be attached to the flanged clip on the foot pads Lastly attach the 4 valance tie downs from the top grommet to the bottom grommets securing to the foot pads using the clips on end of the straps ANCHORING YOUR UNIT This canopy is designed for use as a temporary structure After assembly the canopy MUST BE securely anchored to the ground to prevent damage from winds Your canopy will act like a kite in the wind if not properly and securely anchored to the ground Severe winds will cause the frame to twist and unanchored legs will fall thereby collapsing the canopy If severe winds are expected you must remove the cover from the frame to prevent damage Step 1 Measure out at least 36in from each leg Screw each anchor into the ground leaving 2in between the ground and the eye of each anchor We strongly recommend that your unit be anchored 36in from each leg although this may not be possible in all cases DO install anchors as close to 36in away from legs as possible Step 2 Tie anchor cable or rope around the connector at the top of each leg of the canopy Step 3 Securely tie the other end of the
8. pull cord taut until ball stops Wrap the cord around the pole and under the ball This will hide the ball under the cover and provide a more finished look to your unit e Start by attaching 2 elastic ball straps at each of the four corners e Continue attaching straps from left to right in a zigzag pattern down both sides of the canopy e Attach straps at the front and back of the unit again using a zigzag pattern until all straps are secured Note The ball straps are long enough to accommodate various cover lengths If your straps need a tighter fit they can be shortened by making an additional knot in the cord strap Slide the ball upward to reveal the tied knot Tie a new knot above the old one The size of the knot will determine how short the strap becomes Slip the ball down over the new knot and secure DO NOT CONNECT LEG POLES AT THIS POINT WALLS AND LEGS ASSEMBLY Step 1 Unfold each of the walls e The back wall solid and front wall with zippers e The side walls of the unit feature 3 windows each Step 2 Find the hook amp loop fastening strips on one length of the first sidewall to be assembled These strips are to be placed on the top pipe of your canopy structure by wrapping the fastening strips over the perimeter poles Repeat with second side wall rear wall and front wall Note You may attach the side and rear walls with the window shades facing either the inside or outside of the unit They are designed
9. to be assembled either way Inside View of Hook Aea and Loop Fasteners NOW CONNECT THE LEG POLES TO THE ROOF ASSEMBLY WITH THE COVER ALREADY POSITIONED ON TOP OF THE UNIT Step A First insert the pipes for the middle poles into the 3 and 4 way connectors and then connect the end leg pipes in the same way See illustration Step B Push the eight foot pads onto the bottom of each leg NOTE the foot pads are NOT for anchoring the canopy d f Step C Connect the hook amp loop fastening strips down the length of each leg insert First U YD Step 3 After connecting the top of the side walls and installing the leg pipes into the connectors on the perimeter of the unit use elastic ball straps to connect the end of each sidewall to the 4 corners of the unit IMPORTANT Once the legs and cover are assembled your canopy will act like a kite in the wind It is imperative that the canopy anchors be installed NOW INSTALLING THE LEG SKIRTS Step 1 After the legs have been connected to the roof using the 3 and 4 way connectors and your canopy has been securely anchored attach the leg skirts using elastic ball straps and the grommets at the top of the unit Make sure that the end walls are underneath the flared leg covers to minimize rain and other elements from entering inside the canopy unit Step 2 Next secure the flared leg covers over the 4 corners and outside the walls by fastening the fabric loo
Download Pdf Manuals
Related Search