Rust-Oleum Automotive 253438 Use and Care Manual
Contents
1. during use Hold can upright 10 12 from surface and spray ina steady back and forth motion slightly overlapping each stroke Keep the can in motion while spraying Remove any overspray from the auto finish immediately For best results apply 2 coats allowing 1 2 minutes between coats Do not use near open flame DRY amp RECOAT Dry time and recoat times are based on 70 F and 50 relative humidity Allow more time at cooler temperatures The surface can be recoated within 1 hour or after 24 hours Allow 72 hours for full cure before placing objects in the truck bed CLEAN UP Wipe off tip when finished Clean up wet paint with xylene or mineral spirits Properly discard empty container Do not burn or place in home trash compactor CLOGGING If the valve clogs twist and pull off spray tip and rinse ina solvent such as mineral spirits Do not insert any object into can valve opening Form GDH 429 Rev 081114 TECHNICAL DATA AUTOMOTIVE TRUCK BED COATING AEROSOL PHYSICAL PROPERTIES TRUCK BED COATING AEROSOL Resin Type Alkyd Pigment Type Varies with color Solvents Aromatics hydrocarbons and Ketones MIR 1 20 Max Fill Weight 15 ounces Recommended Dry Film 1 0 1 5 mils Thickness DFT Per Coat 25 37 5y Practical Coverage 15 20 sq ft can at Recommended DFT 1 4 1 9 m can Dry Times at 70 80F Touch 1 hour 21 27 C and 50 re Relative Humidi2. Pp TECHNICAL DATA ATO 16 AUTOMOTIVE TRUCK BED COATING AEROSOL DESCRIPTION AND USES Rust Oleum Auto Truck Bed Coating is designed to provide a durable abrasion resistant textured non skid finish to truck beds It provides a barrier from rust and protects the surface from impact scratches weather and fading It reduces road noise and contours to the exact shape of the truck bed For use on bare or primed metal truck beds Not for use on surfaces that will come in direct contact with heat or high temperatures such as mufflers exhaust components etc Rust Oleum Truck Bed Coating features an advanced spray system that allows you to spray at any angle even upside down for those hard to reach areas A comfort spray tip with a wider finger pad reduces fatigue caused by continuous spraying PRODUCTS SKU 15 ounces Description 253438 Tan 248914 Black PAINTING APPLICATION PAINTING CONDITIONS Use outdoors or in a well ventilated area such as an open garage Use when temperature is between 50 90 F 10 32 C and humidity is below 85 to ensure proper drying Avoid spraying in very windy and dusty conditions Cover surrounding area to protect from spray mist SURFACE PREPARATION Bare Metal or Sound Rust Surfaces Remove all dirt grease oil salt and chemical contaminants by washing the surface with a commercial detergent or other suitable cleaning method Rinse with fresh water and allow to thoroughly dry Rem
3. ove loose paint and rust with a wire brush or 120 220 grit sandpaper Remove all sanding dust with a clean cloth Protect and mask off all surrounding areas to prevent overspray For best results spot prime bare or rusted surfaces Previously Painted Surfaces Thoroughly clean the area with a commercial detergent or other suitable cleaning method Rinse with fresh water and allow to thoroughly dry Note Cleaning is recommended before and after wire brushing or sanding Use a wire brush to remove any loose or peeling paint Sand the surface with 120 220 grit sandpaper The use of 249321 Primer Sealer or any of the sandable primers 249419 Red 252472Light Gray or 249415 Gray will enhance corrosion resistance and improve hiding PRODUCT APPLICATION cont WARNING If you scrape sand or remove old paint you may release lead dust LEAD IS TOXIC EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS SUCH AS BRAIN DAMAGE ESPECIALLY IN CHILDREN PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE Wear a NIOSH approved respirator to control lead exposure Clean up carefully with a HEPA vacuum and a wet mop Before you start find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1 800 424 LEAD or log on to www eps gov lead APPLICATION Shake can vigorously for one minute after the mixing ball begins to rattle If mixing ball fails to rattle DO NOT STRIKE CAN Contact Rust Oleum Shake often
4. ty Recoat Within 1 hour or after 24 hours Full Cure 72 hours Dry Heat Resistance 200 F 93 C Shelf Life 5 years Flash Point 156 F 104 C Safety Information For additional information see MSDS The technical data and suggestions for use contained herein are correct to the best of our knowledge and offered in good faith The statements of this literature do not constitute a warranty express or implied as to the performance of these products As conditions and use of our materials are beyond our control we can guarantee these products only to conform to our standards of quality and our liability if any will be limited to replacement of defective materials All technical information is subject to change without notice 7 Rust Oleum Corporation Form GDH 429 nl RU ST O L E U M 11 Hawthorn Parkway Phone 877 385 8155 Rev 081114 Vernon Hills Illinois 60061 www rustoleum com BRANDS An RPM Company
Download Pdf Manuals
Related Search