Woods Equipment 1013460 User's Manual
Contents
1. Installation 5 Install Front Mounts With Woods LS84 Loader Mount Attach front mount 32 to the right loader mount using two cap screws 26 hardened flat washers 23 and hex nuts 27 23 57817 5 8 Hardened flat washer 26 902 5 8 NC x 2 HHCS GR5 27 230 5 8 NC Hex nut 32 1026846 Front mount LS84 only Woods LS84 Right Loader Mount CD6602B 1 With New Holland 14LA Loader Mount or Woods LC96 LC102 1009 1012 Loader Mount NOTE Front mounts can be installed over the loader mount or loader mount and mid mount mower bracket Pictures show mid mount installed 1 Remove two bolts connecting loader mount mid mount mower bracket to the tractor frame See Figure 5 2 Attach left front mount 8 to tractor using two cap screws 20 and hardened flat washers 23 If mid mount is installed use cap screws 19 See Figure 6 3 Attach right front mount 9 to tractor using two cap screws 20 and hardened flat washers 23 If mid mount is installed use cap screws 19 See Figure 7 SE ke Figure 5 Remove Hardware Left Side Shown Used with OEM or Woods a Figure 6 Left Front Mount Installed 19 or 20 r LC96 LC102 1009 1012 Loader 19 20 23 19 or 20 CD6602B 2 Figure 7 Front Mount Installation 8 1013475 9 1026847 307430 307429 57817 Left front mount Right front mount M16 x 2 0P x 70 mm Cap screw M16 x 2 0P x 55 mm Cap s2. 31 35 47 49 67 7 16 5 8 36 48 55 75 78 106 1 2 3 4 55 75 85 115 120 163 9 16 13 16 78 106 121 164 171 232 5 8 15 16 110 149 170 230 240 325 3 4 1 1 8 192 261 297 403 420 569 7 8 1 5 16 306 416 474 642 669 907 1 1 1 2 467 634 722 979 1020 1383 AA METRIC SERIES Metric Bolt Head TT A TORQUE K Identification Zoe Fa etric A CHART Grade 8 8 Grade 106 COARSE THREAD FINE THREAD A MARKING ON HEAD MARKING ON HEAD A ere SE Metric 8 8 Metric 10 9 Metric 8 8 Metric 10 9 ba Millimeters Size N m Ibs ft N m Ibs ft N m lbs ft N m Ibs ft Millimeters 6 x 1 0 10 mm 8 6 11 8 8 6 11 8 6 x 1 0 8x 1 25 13 mm 20 15 27 20 21 16 29 22 8x 1 0 10x 1 5 16mm 39 29 54 40 41 30 57 42 10 x 1 25 12 x 1 75 18 mm 68 50 94 70 75 55 103 76 12 x 1 25 14 x 2 0 21 mm 109 80 151 111 118 87 163 120 14x 1 5 16 x 2 0 24 mm 169 125 234 173 181 133 250 184 16x 1 5 18 x 2 5 27 mm 234 172 323 239 263 194 363 268 18x 1 5 20 x 2 5 30 mm 330 244 457 337 367 270 507 374 20x 1 5 22x 2 5 34 mm 451 332 623 460 495 365 684 505 22x 1 5 24 x 3 0 36 mm 571 421 790 583 623 459 861 635 24 x 2 0 30 x 3 0 46 mm 1175 867 1626 1199 1258 928 1740 1283 30 x 2 0 Typical Washer Flat Washer Installations Lock Washer N W e NN di N S Z o gel O a fo V 6 9 KI 8 9 00 2 0 A p p en d IX Bolt Torque amp Size Charts Rev 3 28 2007 BOLT SIZE CHART NOTE Chart shows bolt thread sizes and corresponding head wrench sizes for standard SAE and metric bolts S
3. Installation 11 Install Hydraulic Block and Fittings 1 Locate the hydraulic manifold block on the right 7 2472 5 16 Lock washer side of the tractor just under the fender Figure 8 307130 M8 x 1 25P x 40 mm Cap screw Jay end remove the EES 9 307134 M8 x 1 25P x 100 mm Cap screw 2 Attach hydraulic block 18 to tractor using new o 11 313049 Elbow 9 16 ORBM x 9 16 JICM rings 14 three cap screws 8 and one cap 14 62726 O ring 487 x 103 screw 9 plus washers 7 Make sure o rings are 15 63558 Elbow 9 16 JICM x 9 16 ORBM properly seated during installation 18 1011423 Hydraulic block 3 Install elbows 15 and 11 into ports shown in Figure 20 Point elbows rearward 14 e Om w oe el Sg 0 a dE 15 18 See NS AS aS OSS 11 9 E z CD6603 2 Figure 19 Hydraulic Manifold Location Figure 20 Hydraulic Block and Fitting Installation Install Hydraulic Hoses 1 Attach male quick coupler 17 to end of hose 2 2 Connect opposite end of hose 2 to 90 degree KE 15 elbow 15 in the hydraulic block Route hose over rear axle and out the back of the tractor 3 Attach straight end of hose 12 to 45 degree elbow 11 on the hydraulic block 4 Attach 90 degree end of hose 12 to elbow 13 connected to the bulkhead adapter bracket CD6603 5 2 1009493 Hose 40 x 3 8 NPTM x 9 16 JICF 11 313049 Elbow 9 16 ORBM x 9 16 JICM 12 360215 Hose 14 x 9 16 JICF x 9 16 JICF 13 38604 Elbow 9
4. in the Sub Frame Mount Installation section of this manual Any other use or modification of this mounting kit may result in serious injury or death m Hydraulics must be connected as instructed in this manual Do not substitute parts modify or connect in any other way m After connecting hoses check that all control lever positions function as instructed in the Opera tor s Manual Do not put into service until control lever and equipment movements are correct HR Safety instructions are important Read all attachment and power unit manuals follow all safety rules and safety decal information Replace ment manuals and safety decals are available from your dealer To locate your nearest dealer check the Dealer Locator at www WoodsEquipment com or in the United States and Canada call 1 800 319 6637 Failure to follow instructions or safety rules can result in serious injury or death E Know your controls and how to stop engine and attachment quickly in an emergency E Keep hands and body away from pressurized lines Use paper or cardboard not hands or other body parts to check for leaks Wear safety goggles Hydraulic fluid under pressure can easily penetrate skin and will cause serious injury or death 4 Point SFMK Rev 5 8 2006 E Make sure that all operating and service person nel know that if hydraulic fluid penetrates skin it must be surgically removed as soon as possible by a doctor familiar with this form of in
5. 16 JICM x 9 16 JICF 90 15 63558 Elbow 9 16 JICM x 9 16 ORBM 17 64800 Quick coupler male Figure 21 Hydraulic Hoses Installed Figure 22 Hydraulic Hose Installation 1 2 In S ta Ila tion MANO0406 Rev 9 7 2007 Install Bulkhead Adapter on Backhoe Mount 1 Attach bulkhead adapter 1 to crossmember between backhoe brackets Secure with nut sup plied with adapter 2 Attach elbow 10 and female quick coupler 16 to bulkhead adapter as shown in Figure 23 3 Position elbow and quick coupler to point upward 1 1006144 Adapter Bulkhead 3 8 NPTM x 3 4 JICM 10 313017 Elbow 3 8 NPTM x 3 8 NPTF 90 16 64299 Quick coupler female Install Hoses to Backhoe Valve NOTE Some hydraulic fittings supplied in this hose kit may not be required for this application 1 Attach hose 5 between the IN port on the back hoe valve and the bulkhead adapter on the cross member 2 Attach male quick coupler 17 to hose 4 3 Attach opposite end of hose 4 to the OUT port of backhoe valve 4 1010924 Hose 40 x 3 8 NPTM x 3 4 ORBM 5 1013479 Hose 10 x 3 4 JICF x 3 4 ORBM 17 64800 Quick coupler male Install Rear Tires When hydraulic hoses have been comply installed install rear tires NOTE On tractors equipped with Turf tires 13 6 16 adjust tire width to 46 6 inches center to center Figure 25 Rear Tire Spacing see ae been Installation 13 Mount Bac
6. 5 mm 4 24mm 125 Ibs ft 169 N m 24 M16 x 2 0P x 40 mm 2 24mm 125 Ibs ft 169 N m 26 5 8 NC x 2 8 15 16 170 Ibs ft 230 N m 28 5 8 NC x3 4 15 16 170 Ibs ft 230 N m Attach Backhoe Mounts to Backhoe NOTE Leave all hardware loose until backhoe has 3 1013464 Right backhoe mount been mounted to the tractor 4 1013465 Left backhoe mount 1 Attach right backhoe mount 3 and left backhoe 10 1012852 Crossmember link 6500 mount 4 to backhoe frame 15 1093 1 2 NC Hex nut 2 Secure into position using six three per bracket 17 1450 3 4 NC Hex nut cap screws 25 hardened flat washers 21 and BH6500 BH7500 only hex nuts 17 18 24576 1 2 NC x 1 3 4 Cap screw GR5 3 Secure crossmember 10 to backhoe brackets 21 57798 3 4 Hardened flat washer using four cap screws 18 hardened flat wash 22 57816 1 2 Hardened flat washer ers 22 and hex nuts 15 25 735 3 4 NC x 2 Cap screw GR5 BH70 X BH80 X BH6500 BH7500 CD6602 5 Figure 15 Backhoe Mounts Installed Figure 16 Backhoe Mount Installation Rev 5 2 2008 10 Installation WEE HYDRAULIC INSTALLATION A WARNING E Keep hands and body away from pressurized lines Use paper or cardboard not hands or other body parts to check for leaks Wear safety gog gles Hydraulic fluid under pressure can easily penetrate skin and will cause serious injury or death m Make sure that all operating and service per sonnel know that if hydraulic fluid penetrates skin it must b
7. AE Bolt Thread Sizes 5 16 3 8 1 2 000000 MM 100 125 SOOC AT Metric Bolt Thread Sizes 8MM 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS LCE Agriculture ASABE wiissitnccsencees American Society of Agricultural amp Biological Engineers formerly ASAE ASAE American Society of Agricultural Engineers AUP siieeicttohinienndacne Automatic Transmission Fluid BSPP onanan British Standard Pipe Parallel DGPITM British Standard Pipe Tapered Male EN ee E O ees Constant Velocity COW raie naa a oae aE enee Counter Clockwise ENN eeneg Clockwise SE Female H EE Full Thread GA EE Gauge GRIS Cte E Grade 5 etc FIGS EE Hex Head Cap Screw e EE Heat Treated WNC aiana Joint Industry Council 37 Degree Flare LUE WEE Left Hand RE Left UE Meier AU De Millimeter E E geess Male let ME Mega Pascal KEE Newton Ke National Coarse NF uiaiia anni a ged National Fine NPDOM National Pipe Straight Mechanical VR RE National Pipe Tapered NPT SWF National Pipe Tapered Swivel Female ORBM science eli eerste O Ring Boss Male Beideler Pitch EE ege deeg Power Beyond SMe EE Pounds per Square Inch Po OR EE Power Take Off OD hers feted eer Quick Disconnect PRP seide aonn a a Right Hand ROPS eseu esggebee gr Roll Over Protective Structure EM Sees ees ee E Revolutions Per Minute RT RE Right EE Society of Automotive Engineers Ji Le Unified Coarse E T Unified Fine IL Unified Special Bolt Torqu
8. WOODS 1013460 4 POINT SUB FRAME MOUNTING KIT for Backhoe Models BH70 X BH80 X BH6500 BH7500 on New Holland Tractors T2220 TC29DA TC33DA TC34DA FWA or Case IH Tractor Farmall 31 Farmall 35 DX34 FWA with Woods LS84 LC96 LC102 1009 1012 Loaders New Holland 14LA Loader or Case IH L340 Loader Includes Hose Kit 1013484 a UA Tested Proven Unbeatable MANO406 Rev 5 2 2008 JINKS ul oe MANWAL TO THE DEALER Assembly and proper installation of this product is the responsibility of the Woods dealer Read manual instructions and safety rules Make sure all items on the Dealer s Pre Delivery and Delivery Check Lists in the Operator s Manual are completed before releasing equipment to the owner The dealer must complete the Product Registration online at the Woods Dealer Website or complete the mail in form included with the Operator s Manual If using the mail in form the dealer is to return the prepaid postage portion to Woods give one copy to the customer and retain one copy Failure to register the product does not diminish customer s warranty rights TO THE OWNER Read this manual before operating your Woods equipment The information presented will prepare you to do a better and safer job Keep this manual handy for ready reference Require all operators to read this manual carefully and become acquainted with all adjustment and operating procedures before attempting to operate R
9. WOODS Backhoe Operator s Manual for backhoe assembly instructions Leave all hardware loose until sub frame has been fit up or otherwise specified in the instructions This mount can be installed on tractors equipped with a New Holland mid mount mower Sub frame can be installed with mower attached but may be easier if mower is removed from tractor 1 Place jackstands under rear axle and remove both rear tires 2 Disconnect the anti sway bars Figure 1 from the anti sway brackets and remove front half Store front half of anti sway bars for later use when backhoe is removed 3 Attach back half of anti sway bars to the side of 3 point arm to prevent them from pivoting during backhoe operation 4 Remove top link 5 Remove ROPS hardware and spacer from both sides of rear axle See Figure 2 6 With spacer removed cut bottom flange off of spacers Spacer will be reused when sub frame is installed Make sure cut is flush with side flanges See Figure 3 W A E BZ DP11 i Figure 1 Remove Front Half of Anti Sway Link Bars Right Side Shown Figure 3 Remove Flange As a valued customer Woods appreciates your comments Once sub frame and hydrau lic hoses have been installed please take a few minutes to complete the Sub Frame Mount Evaluation sheet that was supplied with your sub frame Your comments will help us continue to bring you quality products Rev 5 2 2008 MAN0406 Rev 9 7 2007
10. ative dealer distributor service person salesperson or employee of any company including without limitation WOODS its authorized dealers distributors and service centers is authorized to alter modify or enlarge this Warranty Answers to any questions regarding warranty service and locations may be obtained by contacting Woods Equipment ALITEC Compan pany BMP 2606 South Illinois Route 2 site rman oes CENTRAL FABRICATORS Oregon IL 61061 GANNON GILL WAIN ROY 800 399 6637 fax frre www WoodsEquipment com HM sa WOODS 800 319 6637 tel F 8494 Rev 6 23 2005 WARRANTY All Models Except Mow n Machine Zero Turn Mowers and Woods Boundary Utility Vehicles Please Enter Information Below and Save for Future Reference Date Purchased From Dealer Model Number Serial Number Woods Equipment Company WOODS warrants this product to be free from defect in material and workmanship Except as otherwise set forth below the duration of this Warranty shall be for TWELVE 12 MONTHS COMMENCING ON THE DATE OF DELIVERY OF THE PRODUCT TO THE ORIGINAL PURCHASER Woods backhoe models BH70 X BH80 X and BH90 X are warranted for two 2 years from the date of delivery to the original purchaser The warranty periods for specific parts or conditions are listed below Part or Condition Model Number Warranted Duration from date of delivery to the original pur
11. ave been discovered routed through the dealer and distributor from whom the purchase was made transportation charges prepaid WOODS shall complete such repair or replacement within a reasonable time after WOODS receives the product THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY WOODS MAKES NO OTHER WARRANTY EXPRESS OR IMPLIED AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE WOODS shall not be liable for any incidental or consequential losses damages or expenses arising directly or indirectly from the product whether such claim is based upon breach of contract breach of warranty negligence strict liability in tort or any other legal theory Without limiting the generality of the foregoing Woods specifically disclaims any damages relating to i lost profits business revenues or goodwill ii loss of crops iii loss because of delay in harvesting iv any expense or loss incurred for labor supplies substitute machinery or rental or v any other type of damage to property or economic loss This Warranty is subject to any existing conditions of supply which may directly affect WOODS ability to obtain materials or manufacture replacement parts No agent represent
12. chaser BW1260 BW1800 8 years BB48X BB60X BB72X BB84X BB600X BB720X BB840X BB6000X lt BB7200X BB8400X DS1260 DSO1260 DS1440 TS1680 BW 126 2 BW180 2 yeats Gearbox PHD25 PHD35 PHD65 PHD95 2162 3240 DS96 DS120 RCC42 RM550 2 components RM660 2 RM990 3 PRD6000 PRD7200 PRD8400 7144RD 2 9180RD 2 5 years 9204RD 2 S15CD S20CD S22CD S25CD 27CD RDC54 RD60 RD72 3 years a year if used in rental or commercial applications RMS550 2 RM660 2 RM990 3 PRD6000 PRD7200 PRD8400 7144RD 2 3 vente 9180RD 2 9204RD 2 y BB600 BB720 BB840 BB6000 BB7200 BB8400 BW126 2 BW180 2 io vear BW1260 BW1800 2162 3240 DS1260 DSO1260 DS1440 TS1680 years Blade spindles Rust through Under no circumstances will this Warranty apply in the event that the product in the good faith opinion of WOODS has been subjected to improper operation improper maintenance misuse or an accident This Warranty does not apply in the event that the product has been materially modified or repaired by someone other than WOODS a WOODS authorized dealer or distributor and or a WOODS authorized service center This Warranty does not cover normal wear or tear or normal maintenance items This Warranty also does not cover repairs made with parts other than those obtainable through WOODS This Warranty is extended solely to the original purchaser of the product Should the original purchaser sell o
13. crew use without mid mount bracket 5 8 Hardened flat washer 6 Installation MAN0406 Rev 9 7 2007 Install Tractor Brackets With Woods LS84 Loader Mount 1 Place left tractor bracket 2 under left side of 4 Place right tractor bracket 1 under right side of tractor Use a hydraulic floor jack to help raise tractor Use a hydraulic floor jack to help raise and hold tractor bracket in position Attach left tractor bracket 2 to left loader mount using two cap screws 26 hardened flat washers 23 and hex nut 27 Attach tractor bracket to the bottom of rear axle and hold tractor bracket in position Attach right tractor bracket 1 to front mount 32 using two cap screws 26 hardened flat washers 23 and hex nut 27 Attach tractor bracket to the bottom of rear axle using two cap screws 16 four hardened flat using two cap screws 16 four hardened flat washers 22 hex nuts 15 and modified spacer washers 22 hex nuts 15 and modified spacer NOTE Place tractor spacer between ROPS brackets with flange on top 1 1013462 Right tractor bracket 2 1013463 Left tractor bracket 15 1093 1 2 NC Hex nut 16 13563 1 2 NC x 6 Cap screw GR5 22 57816 1 2 Hardened flat washer 23 57817 5 8 Hardened flat washer 26 902 5 8 NC x 2 Cap screw GR5 16 27 230 5 8 NC Hex nut 22 32 1026846 Right front mount Tractor Spacer Woods LS84 Loader Mount Used wit
14. e amp Size Charts Rev 3 28 2007 Appendix 21 WARRANTY Replacement Parts For All Models Except Mow n Machine Zero Turn Mowers and Woods Boundary Utility Vehicles Woods Equipment Company WOODS warrants this product to be free from defect in material and workmanship for a period of ninety 90 days from the date of delivery of the product to the original purchaser with the exception of V belts which will be free of defect in material and workmanship for a period of 12 months Under no circumstances will this Warranty apply in the event that the product in the good faith opinion of WOODS has been subjected to improper operation improper maintenance misuse or an accident This Warranty does not cover normal wear or tear or normal maintenance items This Warranty is extended solely to the original purchaser of the product Should the original purchaser sell or otherwise transfer this product to a third party this Warranty does not transfer to the third party purchaser in any way There are no third party beneficiaries of this Warranty WOODS obligation under this Warranty is limited to at WOODS option the repair or replacement free of charge of the product if WOODS in its sole discretion deems it to be defective or in noncompliance with this Warranty The product must be returned to WOODS with proof of purchase within thirty 30 days after such defect or noncompliance is discovered or should h
15. e surgically removed as soon as possible by a doctor familiar with this form of injury or gangrene serious injury or death will result CONTACT A PHYSICIAN IMMEDIATELY IF FLUID ENTERS SKIN OR EYES DO NOT DELAY A WARNING E Make sure all hydraulic hoses fittings and valves are in good condition and not leaking before starting power unit or using equipment Check and route hoses carefully to prevent dam age Hoses must not be twisted bent sharply kinked frayed pinched or come into contact with any moving parts Operate moveable components through full operational range to check clear ances Replace any damaged hoses immediately Assemble Bulkhead Bracket 1 Connect bulkhead adapter 3 to bulkhead bracket 6 and secure using hex nut provided with adapter 2 Attach female quick coupler 16 to the backside of bulkhead adapter 3 and elbow 13 to the front side Position elbow to point upward 3 Remove front hex nut and washer that connect offset bar to the right tractor bracket 4 Place bulkhead bracket on the inside of the trac tor bracket and secure into position using hex nut and washer previously removed Figure 17 Bulkhead Bracket Installed 3 1009495 Adapter 3 8 NPTM x 9 16 JICF 6 1013521 Bulkhead bracket 13 38604 Elbow 9 16 JICM x 9 16 JICF 90 16 64299 Quick coupler female 3 8 CD6603 1 Figure 18 Bulkhead Bracket Installation MAN0406 Rev 9 7 2007
16. eeves if damaged or if protective sleeve cannot be properly positioned or secured Safety Rules continued on next page Safety 3 SAFETY RULES AA ATTENTION BECOME ALERT YOUR SAFETY IS INVOLVED A Safety Rules continued from previous page H Make sure all hydraulic hoses fittings and valves are in good condition and not leaking before starting power unit or using equipment Check and route hoses carefully to prevent damage Hoses must not be twisted bent sharply kinked frayed pinched or come into contact with any moving parts Operate moveable components through full operational range to check clearances Replace any damaged hoses immediately H Always wear relatively tight and belted clothing to avoid getting caught in moving parts Wear sturdy rough soled work shoes and protective equipment for eyes hair hands hearing and head and respirator or filter mask where appropriate m Power unit must be equipped with ROPS or ROPS cab and seat belt Keep seat belt securely fastened Falling off power unit can result in death from being run over or crushed Keep foldable ROPS system in locked up position at all times H Remove seat and upper support assembly before installing or removing backhoe from tractor Failure to comply may result in equipment failure and or personal injury m Make sure attachment is properly secured adjusted and in good operating condition H A minimum 20 of tractor and equipment
17. eplacement manuals can be obtained from your dealer To locate your nearest dealer check the Dealer Locator at www WoodsEquipment com or in the United States and Canada call 1 800 319 6637 The equipment you have purchased has been carefully engineered and manufactured to provide dependable and satisfactory use Like all mechanical products it will require cleaning and upkeep Lubricate the unit as specified Observe all safety information in this manual and safety decals on the equipment For service your authorized Woods dealer has trained mechanics genuine Woods service parts and the necessary tools and equipment to handle all your needs Use only genuine Woods service parts Substitute parts will void the warranty and may not meet standards required for safe and satisfactory operation Record the model number and serial number of your equipment in the spaces provided Model Date of Purchase Serial Number see Parts section for location Provide this information to your dealer to obtain correct repair parts Throughout this manual the term NOTICE is used to indicate that failure to observe can cause damage to equipment The terms CAUTION WARNING and DANGER are used in conjunction with the Safety Alert Symbol a triangle with an exclamation mark to indicate the degree of hazard for items of personal safety This is the safety alert symbol It is used to alert you to potential personal A injury hazards Obey all safety me
18. h 3 Woods L 84 o7 23 Loader Only CD6602B 2A 32 Figure 8 Tractor Brackets Installed with LS84 Loader Installation 7 MAN0406 Rev 9 7 2007 Install Tractor Brackets 1 Place left tractor bracket 2 under left side of tractor Use a hydraulic floor jack to help raise and hold tractor bracket in position 2 Attach left tractor bracket to left front mount 8 using two cap screws 26 hardened flat washers 23 and hex nut 27 NOTE Tractors equipped with mid mount mower place tractor bracket on the inside of front mount as shown in Figure 9 Tractors without mid mount mower place on the outside of front mount 3 Attach tractor bracket to the bottom of rear axle using two cap screws 16 four hardened flat washers 22 hex nuts 15 and modified spacer NOTE Place tractor spacer between ROPS Figure 9 Left Tractor Bracket Attached brackets with flange on top to Front Mount 4 Repeat steps to install right tractor bracket 1 1013462 Right tractor bracket 1013463 Left tractor bracket 1013475 Left front mount 9 1026847 Right front mount 15 1093 1 2 NC Hex nut 16 13563 1 2 NC x 6 Cap screw GR5 22 57816 1 2 Hardened flat washer 23 57817 5 8 Hardened flat washer 26 902 5 8 NC x 2 Cap screw GR5 5 8 NC Hex nut on Tractor Spacer CD6602B 2B Figure 10 Tractor Bracket Installation 8 Installation ME Install Cross Brace 1 Remove PTO sh
19. hoe stabilizer arms or along side of tractor to avoid being trapped should the boom swing control be accidentally activated A WARNING m Remove seat and upper support assembly before installing or removing backhoe from power unit Failure to comply may result in equipment failure and or personal injury 1 Position tractor on a hard level surface and cen ter the backhoe boom 2 Lower stabilizers and take backhoe weight off tractor 3 Lower boom and dipper to form 90 degree angle and rest bucket on the ground 4 Remove the seat assembly 5 Remove klik pins from bolt and nut assemblies 6 Use 1 1 2 inch open end wrench supplied with the mounting kit to remove hex nuts Return wrench to storage position see Figure 26 10 11 12 13 13 Use the boom to relieve excess pressure on 1 inch bolts and remove bolts Tilt backhoe main frame to separate slots on the backhoe brackets from the tractor brackets Raise stabilizers until backhoe brackets slide out of hooks on the bottom of the tractor brackets Move tractor forward to clear backhoe brackets Place 6 inch blocks under backhoe mainframe and raise stabilizers to lower backhoe to the stor age position on blocks as shown Boom and dip per should be at 90 degree angle Turn off engine set brakes and remove key Disconnect backhoe hydraulic system See STORAGE on page 17 Reinstall seat assembly NOTE For instruc
20. ia EE 15 63558 1 Elbow 9 16 JICM x 9 16 ORBM 1013479 Hose 10 x 3 4 JICF x 3 4 ORBM 1r LEE EE Geet 17 64300 2 Quick coupler male 18 1011423 1 Hydraulic block 307130 M8 x 1 25P x 40 mm HHCS 307134 M8 x 1 25P x 100 mm HHCS 10 313017 Elbow 3 8 NPTM x 3 8 NPTF 90 4 1 5 1 6 1013521 1 7 2472 4 5 16 Lock washer 8 3 9 1 HHCS Hex Head Cap Screw Standard Hardware Obtain Locally MANO0406 Rev 9 7 2007 P ar t S 1 9 application BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific Fasteners must always be replaced with the same grade as specified in the manual parts list Always use the proper tool for tightening hardware SAE for SAE hardware and Metric for metric hardware Make sure fastener threads are clean and you start thread engagement properly All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 amp J1701M JUL 96 L SAE SERIES SAE Bolt Head m TORQUE Identification A A CHART SAE Grade 2 SAE Grade 5 SAE Grade 8 No Dashes 3 Radial Dashes 6 Radial Dashes MARKING ON HEAD Diameter Wrench SAE 2 SAFO SAF 8 Inches Size lbs ft N m lbs ft N m lbs ft N m 1 4 7 16 6 8 10 13 14 18 5 16 1 2 12 17 19 26 27 37 3 8 9 16 23
21. ield 7 1013474 Cross brace 2 Attach cross brace 7 to rear of tractor using two 15 1093 1 2 NC Hex nut cap screws 24 and hardened flat washers 23 18 24576 1 2 NC x 1 3 4 Cap screw GR5 3 Attach to right and left tractor brackets using four 22 57816 1 2 HArdened flat washer two per side cap screws 18 hardened flat 23 57817 5 8 Hardened flat washer washers 22 and hex NUS S 24 64062 M16 x 2 0P x 40 mm Cap screw 4 Install PTO shield CD6602 3 Figure 11 Cross Brace Installed Figure 12 Cross Brace Installation Install Offset Bars 1 Place right offset bar 5 on the outside of right 5 1013472 Right offset bar tractor bracket 6 1013473 Left offset bar 26 23 57817 5 8 Hardened flat washer 26 902 5 8 NC x 2 Cap screw GR5 28 27 230 5 8 NC hex nut 28 34473 5 8 NC x 3 Cap screw GR5 2 Secure to front holes using two cap screws hardened flat washers 23 and hex nuts 27 3 Secure to rear holes using two cap screws hardened flat washers 23 and hex nuts 27 a ws em 4 Repeat steps to install left offset bar 6 CD6602 4 Figure 14 Right Offset Bar Installation see seen Installation 9 Torque Mounting Hardware TORQUE SPECIFICATIONS Wrench Ref Cap Screw Qty Size Required Torque 16 1 2 NC x6 4 1 2 85 Ibs ft 115 N m 18 1 2 NC x 1 3 4 4 1 2 85 Ibs ft 115 N m 19 M16 x 2 0P x 70 mm 4 24mm 125 Ibs ft 169 N m 20 M16 x 2 0P x 5
22. jury or gan grene serious injury or death will result CON TACT A PHYSICIAN IMMEDIATELY IF FLUID ENTERS SKIN OR EYES DO NOT DELAY E To prevent contamination during maintenance and storage clean and then cover hose ends fit tings and hydraulic ports with tape H Check that all hardware is properly installed Always tighten to torque chart specifications unless instructed otherwise in this manual m This mounting kit is designed to provide secure mounting and adequate operator clearance for most operators when properly installed Check clearance dimensions shown below to be sure you have installed seat bracket correctly In some cases it may be necessary to adjust the seat to the lowest position and or as far forward as possible in order to achieve the ideal 40 inch clearance For 36 5 inch radius operation taller operators may need to wear a hardhat for greater comfort and safety 36 5 TO 40 RADIUS TO OVERHANG E Air in hydraulic systems can cause erratic oper ation and allows loads or equipment components to drop unexpectedly When connecting equipment or hoses or performing any hydraulic maintenance purge any air in hydraulic system by operating all hydraulic functions several times Do this before putting into service or allowing anyone to approach the equipment H Protective hose sleeves must cover all hydrau lic hoses within 20 inches of the operator and be secured onto metal hose fittings Replace hoses or sl
23. khoe to Tractor E This mounting kit is designed to provide secure mounting and adequate operator clear ance for most operators when properly installed Check clearance dimensions shown below to be sure you have installed seat bracket correctly In some cases it may be necessary to adjust the seat to the lowest position and or as far forward as possible in order to achieve the ideal 40 inch clearance For 36 5 inch radius operation taller operators may need to wear a hardhat for greater comfort and safety 36 5 TO 40 RADIUS TO OVERHANG SUB FRAME m The only time the backhoe may be operated from a position other than the operator seat is during backhoe attachment and removal Opera tor must e Read Mounting Kit Manual instructions on attaching and removing backhoe and use extreme care e Always stand between rear tire and backhoe stabilizer arms or along side of tractor to avoid being trapped should the boom swing control be accidentally activated A WARNING H Remove seat and upper support assembly before installing or removing backhoe from power unit Failure to comply may result in equipment failure and or personal injury Check Hydraulic System Check all hydraulic fittings and lines to be sure they are tight and free of kinks or twists Mount Backhoe 1 Remove the backhoe seat assembly 2 Back tractor up to backhoe and center mount between the tractor rear tires Position tractor so that the hydra
24. or any incidental or consequential losses damages or expenses arising directly or indirectly from the product whether such claim is based upon breach of contract breach of warranty negligence strict liability in tort or any other legal theory Without limiting the generality of the foregoing Woods specifically disclaims any damages relating to i lost profits business revenues or goodwill ii loss of crops iii loss because of delay in harvesting iv any expense or loss incurred for labor supplies substitute machinery or rental or v any other type of damage to property or economic loss This Warranty is subject to any existing conditions of supply which may directly affect WOODS ability to obtain materials or manufacture replacement parts No agent representative dealer distributor serviceperson salesperson or employee of any company including without limitation WOODS its authorized dealers distributors and service centers is authorized to alter modify or enlarge this Warranty Answers to any questions regarding warranty service and locations may be obtained by contacting Woods Equipment ALITEC Company BMP 2606 South Illinois Route 2 CENTRAL FABRICATORS Post Office Box 1000 GANNON Oregon IL 61061 S 800 319 6637 tel GILL 800 399 6637 fax We d WAIN ROY En HM eis WOODS F 3079 Rev 4 4 2008 PART NO MANO406 Woods Equipment Company 2606 South Illinois Route 2 P
25. ost Office Box 1000 Oregon Illinois 61061 800 319 6637 tel 800 399 6637 fax Wi PO www WoodsEquipment com ai d Saul Fhe BR 2005 Woods Equipment Company All rights reserved WOODS the Woods logo and Tested Proven Unbeatable are trademarks of Woods Equipment Company All other trademarks trade names or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respective companies or mark holders Specifications subject to change without notice
26. r otherwise transfer this product to a third party this Warranty does not transfer to the third party purchaser in any way There are no third party beneficiaries of this Warranty WOODS makes no warranty express or implied with respect to engines batteries tires or other parts or accessories not manufactured by WOODS Warranties for these items if any are provided separately by their respective manufacturers WOODS obligation under this Warranty is limited to at WOODS option the repair or replacement free of charge of the product if WOODS in its sole discretion deems it to be defective or in noncompliance with this Warranty The product must be returned to WOODS with proof of purchase within thirty 30 days after such defect or noncompliance is discovered or should have been discovered routed through the dealer and distributor from whom the purchase was made transportation charges prepaid WOODS shall complete such repair or replacement within a reasonable time after WOODS receives the product THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY WOODS MAKES NO OTHER WARRANTY EXPRESS OR IMPLIED AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE WOODS shall not be liable f
27. racket 19 307430 4 M16x2 0P x 70 mm HHCS 3 1013464 1 Right backhoe bracket 20 307429 4 M16x2 0P x55 mm HHCS 4 1013465 1 Left backhoe bracket 21 57798 6 3 4 Hardened flat washer 5 1013472 1 Right offset bar 22 57816 16 1 2 Hardened flat washer 6 1013473 1 Left offset bar 23 57817 16 5 8 Hardened flat washer 7 1013474 1 Cross brace 24 64062 2 M16 x 2 0P x 40 mm HHCS 8 1013475 1 Left front mount 25 735 6 3 4 NC x2HHCS GR5 9 1026847 1 Front mount OEM LC96 LC102 Idr 26 902 8 5 8 NC x2HHCS GR5 10 1012852 1 Crossmember BH6500 link 27 230 12 5 8 NC Hex nut 11 1006883 1 1 1 2 Open end wrench 28 34473 4 5 8 NC x3 HHCS GR5 12 1007320 2 1 NC x 3 1 2 HHCS GR5 29 66649 4 Pin safety 09 x 2 31 not shown 13 1006861 2 1 NC Slotted hex nut 30 6737 4 Pin 7 16 x 3 1 4 not shown 14 62043 2 1 4 x 1 3 4 Klik pin 31 1006885 2 Decal warning pinch point 15 1093 16 1 2 NC Hex nut 32 1026846 1 Front mount LS84 Idr 16 13563 4 1 2 NC x6 HHCS GR5 17 1450 6 3 4 NC Hex nut HHCS Hex Head Cap Screw BH6500 BH7500 only Standard Hardware Obtain Locally Rev 5 2 2008 18 Parts T E 1013484 HOSE KIT CD6603 REF PART QTY DESCRIPTION REF PART QTY DESCRIPTION 1 1006144 1 Adapter bulkhead 11 313049 1 Elbow 9 16 ORBM x 9 16 JICM 45 3 8 NPTM x 3 4 JICM 12 360215 1 Hose 14 x 9 16 JICF x 9 16 JICF 2 1009493 1 Hose 40 x 3 8 NPTM x 9 16 JICF 13 38604 1 Elbow 9 16 JICM x 9 16 JICF 90 10094951 ca 14 62726 4 O ring 487 x 103 ii
28. ssages that follow this symbol to avoid possible injury or death Indicates a hazardous situation which if not avoided will result in death A DANGER or serious injury A WARNING Indicates a hazardous situation which if not avoided could result in death or serious injury A CAUTION Indicates a hazardous situation which if not avoided could result in minor or moderate injury yan Is used to address practices not related to personal injury SE NOTE Indicates helpful information BMP CENTRAL FABRICATORS GANNON GILL w fr aa WAIN ROY lA a DDD WOODS 2 Introduction RCA SAFETY RULES AA ATTENTION BECOME ALERT YOUR SAFETY IS INVOLVED AA ILEA EL INSTRUCTIVO SZ Si no lee Ingles pida ayuda a t alguien que si lo lea para que le raduzca las medidas de seguridad Safety is a primary concern in the design and manufacture of our products Unfortunately our efforts to provide safe equipment can be wiped out by an operator s single careless act In addition to the design and configuration of equipment hazard control and accident preven tion are dependent upon the awareness con cern judgement and proper training of personnel involved in the operation transport maintenance and storage of equipment It has been said The best safety device is an informed careful operator We ask you to be that kind of operator HR This Sub Frame Mounting Kit is only for the backhoes and tractors specified
29. tions on extended storage see backhoe operator s manual Figure 27 Backhoe Storage Position 16 Installation MAN0406 Rev 9 7 2007 STORAGE Connect Hydraulic Hoses TRACTOR Connect male quick coupler on end of hose to female quick coupler at bulkhead bracket when backhoe is removed from tractor See Figure 28 NOTICE m Failure to connect hoses together will result in damage to tractor hydraulic system BACKHOE Connect IN and OUT quick couplers together to prevent dirt and debris from accumulating in quick couplers See Figure 29 Figure 29 Backhoe Hose Connection Storage Position Typical Attach 3 Point Arms Lower 3 point lift arms and anti sway links can be used on tractor when backhoe is removed Attach 3 point lift arms anti sway links to tractor as shown in Figure 30 Secure anti sway links to tractor using pin 30 and safety pin 29 provided in kit 29 66649 Pin safety 09 x 2 31 not shown 30 6737 Pin 7 16 x 3 14 MAN0406 Rev 9 7 2007 Installation 17 1013460 4 POINT SUB FRAME MOUNTING KIT 31 PN 1006885 PINCH POINT Keep hands clear 1006885 Serial Number Plate MODEL NO SERIAL NO Q Used with OEM EEN MEA O ig EE 1009 1012 Loaders 1920 y oods LS84 Loader Only 26 REF PART QTY DESCRIPTION REF PART QTY DESCRIPTION 1 1013462 1 Right tractor bracket 18 24576 4 1 2 NC x 1 3 4 HHCS GR5 2 1013463 1 Left tractor b
30. tractor bracket hooks Set tractor brake Raise backhoe bracket bottom mounting pins into tractor bracket bottom hooks Rotate backhoe bracket upper mounting slots over tractor bracket mounting hole and align holes 1 1 2 Open End Wrench Storage Position 10 11 12 13 14 15 Install cap screws 12 and slotted hex nuts 13 Tighten with 1 1 2 inch open end wrench provided with kit Return wrench to storage position see Figure 26 Secure hex nut into position with klik pin 14 Shut off tractor and remove key Tighten hardware with backhoe secured to the tractor This will ensure proper alignment and fit up for future installation 1 2 NC x 1 34 0 20 00 85 Ibs ft 115 N m 2A4NCx 297 lIbs ft 403 N m Reinstall seat Start tractor and put backhoe into transport posi tion see backhoe operator s manual NOTE Install swing lock before transporting 12 1007320 1 NC x 3 1 2 Cap screw GR5 13 1006861 1 NC Slotted hex nut 14 62043 1 4 x 1 3 4 Klik pin CD6602 6 Figure 26 Backhoe to Tractor Installation MAN0406 Rev 9 7 2007 Installation 15 Remove Backhoe from Tractor E The only time the backhoe may be operated from a position other than the operator seat is during backhoe attachment and removal Opera tor must e Read Mounting Kit Manual instructions on attaching and removing backhoe and use extreme care e Always stand between rear tire and back
31. ulic system can be connected Shut off tractor set brake remove key 3 Attach backhoe hydraulic system A Connect male quick coupler on hose from OUT port on the backhoe control valve to the female quick coupler on the bulkhead adapter bracket B Connect male quick coupler on hose from hydraulic block to the female quick coupler on the backhoe bracket crossmember 4 With the tractor PTO and transmission in neutral start the engine and run at low idle Hydraulic power is provided when the tractor is started NOTE Very little engine power is required to operate the hydraulic system in this mode Should the engine pull down excessively check the plumbing hook up for reversed lines or a con trol lever stuck in an operating position NOTE You will use the backhoe hydraulics to maneuver the backhoe brackets into position Use care in this procedure to avoid being trapped between tractor and backhoe or between back hoe parts Continued on next page 14 Installation MAN0406 Rev 9 7 2007 Mount Backhoe to Tractor Continued Refer to Figure 26 5 Using the backhoe hydraulics position the back hoe brackets at a slight angle approximately 5 to 10 degrees Raise backhoe up by lowering stabilizers and boom section until backhoe mounting pins on backhoe brackets are slightly lower than tractor bracket hooks Slowly move tractor back until backhoe brackets are positioned below the
32. ving equipment H Refer to backhoe manual and follow all mainte nance safety rules and instructions m Do not modify or alter or permit anyone else to modify or alter the equipment or any of its compo nents in any way E Keep all persons away from operator control area while performing adjustments service or maintenance E Tighten all bolts nuts and screws to torque chart specifications Check that all cotter pins are installed securely to ensure equipment is in a safe condition before putting unit into service m Make sure all safety decals are installed Replace if damaged See Parts section for loca tion 4 Point SFMK Rev 5 8 2006 4 Safety BACKHOE SUB FRAME INSTALLATION Tractor Preparation A WARNING H Only use 1013460 4 Point Sub Frame Mount ing Kit for mounting Woods BH70 X BH80 X BH6500 BH7500 backhoe on New Holland T2220 TC29DA TC33DA TC34DA tractors or Case IH DX34 Farmall 31 Farmall 35 tractors equipped with Woods LS84 LC96 LC102 1009 and 1012 loaders New Holland 14LA loader or Case IH L340 loader Any other use or modifica tion of this mounting kit may result in serious injury or death For installing this sub frame references to right left forward and rearward directions are determined from the operator s position in the tractor seat Do not install 1013460 4 point sub frame on a tractor without a Woods or OEM loader mount attached Refer to the
33. weight must be on the tractor front wheels when attachments are in transport position Without this weight tractor could tip over causing personal injury or death The weight may be attained with a loader Weigh the tractor and equipment Do not estimate m Do not install backhoe and required counter weights on tractor if the total tractor and equipment weight then exceeds the ROPS weight certification of the tractor To reduce overall weight of unit remove liquid from rear tires and remove mid mount mower if equipped m Do not allow bystanders in the area when oper ating attaching removing assembling or servic ing equipment H Before operating make sure stabilizer pads are lowered firmly to the ground Stabilizer arms pro vide support for the backhoe and support for the backhoe mounting brackets E The only time the backhoe may be operated from a position other than the operator seat is dur ing backhoe attachment and removal Operator must e Read Mounting Kit Manual instructions on attaching and removing backhoe and use extreme care e Always stand between rear tire and backhoe stabilizer arms or along side of tractor to avoid being trapped should the boom swing control be accidentally activated m Never leave equipment unattended with engine running or with bucket in raised position Always engage swing and boom transport locks relieve system pressure by operating controls and remove ignition key before lea
Download Pdf Manuals
Related Search