Winegard MA1055G User's Manual
Contents
1. Max Control Panel Size 4 5 x 4 5 x Control Panel Weight 5 Ibs Warning Device 2 amps not included Mount Specifications Height Lowered 5 1 2 Height Raised 33 1 2 Roof Space Required 13 5 x 66 Stowed position Turning Diameter 52 Weight of Mount 11 25 Ibs General Specifications Operating Temperature 10 to 130F Humidity 90 noncondensing Shipping Weight OEM Models 18 25 Ibs Carton Size 48 x 12 x 10 3 4 Rev 8 06 Pre Installation Requirements To install the Winegard Motorized Sensar antenna check with your RV dealer or manufacturer Your RV may already be pre wired for this system and or may have a reinforced roof area available FIGURE 3 Roof Edge STEP 1 Choose location for antenna system on roof area A inches Figure 3 illustrates placement of system showing it in travel position You must be able to raise and rotate antenna without interfering with other roof mounted equipment When selecting location keep in mind how you will route the cables to and from mount Beware of any obstacles in roof area that may interfere with or be damaged during installation STEP 2 Choose location inside RV for mounting control panel Itis recommended thatthe control panel be in viewing area of most watched TV so you can see TV picture to turn antenna to best picture reception for your area A 12VDC In inches power source must also be available 52. 2 Raised Operating Diameter 33 5 Raised Height STEP 1 Aitach antenna head to booms shown in Figure 2 using two pins and E Clips found in hardware package Fasten coax to antenna head See Figure 2B Tighten coax connection per instruction decal on antenna head Leveling Bracket FIGURE 2 Antenna Head 2 Steel Pins Mas un Tubes FIGURE 2B Coax Connector STEP 2 Remove the three screws holding triangle shaped cover with WINEGARD on it from antenna base You will see acoax cable and control cable approx 6 long With antenna System positioned on roof trace the outline of the mount and also trace the inside wall outline of cable area Set mount off to the side of the traced area See figures 3 amp 4 FIGURE 3 Roof Installation STEP 3 In traced triangular area for cables drill a hole 1 5 to 3 Dia in roof Route cables through roofto where you have selected control panel to be mounted See Figure 4 FIGURE 4 Drill hole 1 1 2 to 3 Diameter for Wires on Roof STEP 4 Place antenna system on your previously selected traced location and fasten in place with mounting screws Depending on roof construction you may needto drill pilot holes for mounting screws See Figure 5 FIGURE 5 Don t get Sealant on Painted Turret Top i Mounting O Ring Screws STEP 5 Make cable connections from wires on the roof to wires in mount Apply approved sea
3. WINEGARD MOTORIZED SENSAR ANTENNA Models MA1055W amp MA1055G MADE IN U S A U S Patents D500 496 and 7 358 909 INSTALLATION MANUAL CAUTION This system is not for use with antenna in raised position while vehicle is in motion OEM Model MA1055W has white antenna head and white turret OEM Model MA1055G has gray antenna head and black turret Unit packed as follows Motorized Mount with booms attached Antenna Head Hardware Bag Instructions Power Cable Sold separately CL MAO3 Control Cable Sold separately CL MAO6 Control Panel Sold separately MA CP4W White MA CP4B Black Read Installation Instructions before installing unit Read Motorized Sensar Operation before operating unit Tools needed for installation Tape measure Cutter Phillips screwdriver Electric or cordless drill 1 8 drill bit for pilot holes System Specs for Motorized Sensar Electronic Specifications Tools Needed Specifications 7 16 wrench 5 16 socket nut driver 1 1 2 to 3 hole saw cable entry hole Sealant compatible with roof material check with your vehicle manufacturer for compatibility Operating Voltage Nominal 12VDC Operating range 9 5 VDC to 15 5 VDC Current draw of electronics when Power Light is off Nominal 500uA 1 5mA Max Current draw of electronics when Power Light is on Nominal 46mA 70mA Max Current draw of electronics when Power Light is on and motor running 3 amp
4. d by Winegard in any manner whatsoever removing or defacing any serial number usage notin accordance with product instructions or acts of nature such as damage caused by wind lightning ice or corrosive environments such as salt spray and acid rain This Limited Warranty also does not apply ifthe product becomes unable to performits intended function in any way as a result ofthe television signal provider making any changes in technology or service RETURN AUTHORIZATION POLICY A Return Material Authorization RMA is required priorto returning any product to Winegard Company or Winegard Warranty Services under this warranty policy Please call our Technical Services Department at 800 788 4417 or send an e mail to warranty winegard com to obtain the RMA number Please furnish the date of purchase when requesting an RMA number Enclose the productina prepaid package and write the RMA number in large clear letters on the outside of the package To avoid confusion or misunderstanding a shipment s without an RMA number s or an unauthorized return s will be refused and returned to Customer freight collect WINEGARD COMPANY DOES NOT ASSUME ANY LIABILITIES FOR ANY OTHER WARRANTIES EXPRESS ORIMPLIED MADE BY ANY OTHER PERSON ALL OTHER WARRANTIES WHETHER EXPRESS IMPLIED OR STATUTORY INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY ARE LIMITED TO THE TWO YEAR PERIOD OF THIS WARRANTY In states that do notallow limitati
5. lant around cable entry hole Replace cover over cable area making sure O Ring is in place Then tighten the three cover screws See Figure 5 STEP 6 After antenna is secured to roof apply approved sealant around edge of mount and over screw heads NOTE Consult RV manufacturer for approved sealant Control Panel Installation STEP 1 Run control cable from roof mount to control panel Do not connect to control panel at this time STEP 2 Connect power cable to a fused 12VDC source It is recommended that the power source is separate from other appliances to avoid possible electrical interference Do not connect wire to control panel at this time Note Orange wire supplied for optional Antenna Up warning DO NOT connect it to a 12VDC power source STEP 3 Run coax cable from roof mount to power source for antenna head preamplifier Power source may be a powered 12VDC video switch or wall plate power supply Connect a second coax cable from power source to television Control Panel Inside Installation STEP 4 Control panel can be mounted directly to surface providing surface has sufficient space behind panel for wiring Should you be limited to space behind panel or choose not to have wires concealed behind control panel you can use the surface mount box STEP 5 After prepping area to mount control panel test fitting to make sure it fits in location correctly and connect control cable and power wires to panel Then secure
6. ons on implied warranties or the exclusion of limitation of incidental or consequential damages the above limitations or exclusions do not apply Somestates do notallowlimitations on howlongan implied warranty lasts orthe exclusion of limitation ofincidental or consequential damages so the above limitations or exclusions may not apply to you This warranty gives Customer specific legal rights Customer may also have other rights that may vary from state to state SATELLITE RECEIVER WARRANTY alimi WS MOBWARREV2 Seemanufacturer s limited warranty policy TM Rev 1 10 Notes Printed in U S A Winegard Company 3000 Kirkwood Street e Burlington lowa 52601 2000 Winegard Company 2006 2452068 Rev 3 8 10
7. panel to it s location Refer to Operations Manual for instructions to raise lower and rotate antenna ae 875 Motorized TV Antenna PT RAISE STOW O RAISED Rotate By WINEGARD maa NOTE SHOWN WITHOUT SURFACE MOUNT BOX POWER CABLE CONNECTION CONTROL CABLE CONNECTION Warranty Returned units damaged in shipping due to improper packing will be charged to the dealer customer WINEGARD MOBILE PRODUCTS LIMITED WARRANTY 2 YEARS PARTS 1 YEAR LABOR Winegard Company warrants this product against defects in materials or workmanship fora period of two 2 years from the date oforiginal purchase During year one 1 of such warranty Winegard Company will also pay authorized labor costs to an authorized Winegard dealerto repair or replace defective products No warranty claim willbe honored unless atthe time the claimis made Customer presents proof of purchase to an authorized Winegard dealer to locate the nearest authorized Winegard dealer contact Winegard Company 3000 Kirkwood Street Burlington lowa 52601 Telephone 800 288 8094 or visit www winegard com Customer must provide proof of purchase with a dated sales receipt for the Winegard productto verify the productis under warranty If the date of purchase cannot be verified the warranty period shall be considered to begin thirty 30 days after the date of man
8. ufacture Ifa defectin material or workmanship is discovered Customer may take the productto an authorized Winegard dealer for service Customer must provide proof of purchase to verify the product is under warranty Ifthe productis broughtto an authorized Winegard dealer for service prior to expiration of year one 1 of the warranty period anda defect in material or workmanship is verified by Winegard Technical Services Winegard Company will cover the Winegard dealer s labor charges for warranty service The Winegard dealer must contact Winegard Technical Services in advance for pre approval of the service Approval of the service isatthe sole discretion of Winegard Company Alternatively Customer may ship the product prepaid to Winegard Technical Services located at 31 11 Kirkwood Street Burlington lowa 52601 Telephone 800 788 4417 Customer must return the productalong with a brief description of the problem and provide Winegard Technical Services with Customer s name address and phone number Customer mustalso provide proof of purchase to verify the productis under warranty Ifthe productis returned before the expiration of the warranty period Winegard Company will at its option either repair or replace the product This Limited Warranty does not apply if the product has been damaged deteriorates malfunctions or fails from improper installation misuse abuse neglect accident tampering modification of the product as originally manufacture
Download Pdf Manuals
Related Search