Chicago Electric 42292 User's Manual
Contents
1. CHICAGO JCal Power Tools BATTERY FLOAT CHARGER ole 42292 OPERATING INSTRUCTIONS Distributed Exclusively by L a HARBOR FREIGHT aiy C gt TOOLS tm 3491 Mission Oaks Blvd Camarillo CA 93011 Copyright 2000 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools For technical questions and replacement parts please call 1 800 444 3353 Battery Float Charger The Battery Float Charger is used for the maintenance of wet or gel cell batteries that are stored or used periodically in such items as boats cars snowmobiles ATVs and tractors The Float Charger prevents self discharge of the battery while maintaining and extending the life of rechargeable 12 volt batteries It maintains a battery charge for batteries rated from 5 to 125 amp hours by providing a constant minimum current 13 5 VDC regulated output Other types of chargers provide a strong rapid charge but tend to boil out liquids and decay electrodes It is simple to use Hook it up plug it in and forget it Safety Warnings and Precautions QDo not make connections to battery near open flame sparks or when smoking Q Make connection to battery before plugging charger into electrical outlet Q To prevent damage to charger connect cable clips to proper terminals on battery black clip to2. TO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Note Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts SKU 42292 Page 3
3. negative red clip to positive Q Do not touch clips together while charger is plugged in Q Do not place charger or electrical hookups on ground or floor Q Do not turn on equipment that battery is connected to while charging URemove charger power module from electrical outlet and disconnect the battery clamps when finished Q Do not pull power cord to remove power module from electrical outlet SKU 42292 Page 2 Safety Warnings and Precautions continued Remove battery cell caps before charging Caution Make sure battery is vented if battery is maintenance free and non fillable it has vent slots make sure vents are clear and dirt free Always remove battery from vehicle before charging Use this product in accordance with the battery s and vehicle s manual recommendations safety warnings and charging instructions Caution Never charge battery in an enclosed area Never leave charger unchecked for such periods of time as to create a hazard Caution Surges and sparks in electrical power supply could possibly cause battery explosion Battery charger should be plugged into a surge protector outlet Caution Batteries can explode under certain conditions excessive heat and or poor ventilation can cause battery explosion Specifications Battery Float Charger 12 volts DC 5 to 125 amp hours Voltage Output 13 5 VDC Dimensions 1 3 4 x 1 1 2 x 2 1 4 inches Total length from power m
4. odule to connector clips 53 inches Input Voltage 120 volts AC 60 Hz 14 watts Operation 1 Place Float Charger within 3 feet of battery 2 Connect Red clip to positive terminal of battery 3 Connect Black clip to negative terminal of battery 4 Plug power module into electrical outlet Caution If the Parts Box F is to be mounted on a sub plate do not use a power driver To mount the Parts Box use the included 2 rubber washers and 2 Phillips head screws and hand tighten into place REV 07 02 05 03 02 05 REV 10 05 Parts Listing Parts Diagram Part Description Qty A Lid 1 Power Cord 1 Transformer Body Pin Parts Box Radiator Cover 1 Pan Screw Circuitry Battery Cables Battery Clips maa u NO p j N N PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERE
Download Pdf Manuals
Related Search