AOC CT500G User's Manual
Contents
1. 70 a LF 900 ae 6500 O 800 X 600 EXTERNAL CONTROLS Switch 1 Power On Off Switch 2 LED 3 Menu 4 Contrast 5 Brightness 6 Exit 1 AC Inlet INSTALLATION INSTRUCTIONS SWIVEL BASE To attach the swivel base to the monitor do the following e Carefully turn the monitor on its side or upside down see figure 1 e Locate the cavities at the bottom front of the monitor e Insert the pegs on the swivel base into these cavities Push the swivel base forward until the swivel base locks in place e To remove the swivel base hold the bottom of the swivel base then push it out POWER CORD Power Source 1 Make sure the power cord is the correct type that required in your area 2 This monitor has a universal power supply that allows operation in either 100 120V AC or 220 240V AC voltage area No user adjustment is required 3 Connect the power cord into your monitors power input socket and then plug the other end into a 3 pin AC power outlet The power cord may be connected to either a wall power outlet or the power outlet socket on your PC depending on the type of power cord supplied with your monitor VIDEO CABLE Connecting the Video Cable the monitor comes with a built in video cable Plug the signal cable s 15 pin connector into the computer s video port and tighten the two screws on the cable connector see figure 22. female configuration TECHNICAL SUPPORT FAQ Power LED is not on Check if the Power Switch is in the ON position Power Cord should be connected No Plug amp Play Check if the PC System is Plug amp Play compatible Check if the Video Card is Plug amp Play compatible Check if the D 15 plug pin of Video Cable is bent Make sure the AOC Monitor Drivers are installed AOC Monitor Drivers are available at www aocmonitor com Picture is fuzzy Adjust the Contrast and Brightness Controls Picture bounces or a wave pattern is present in the picture Move electrical devices that may cause electrical interference The power LED is ON orange but there s no video or no picture Computer Power Switch should be in the ON position Computer Video Card should be snugly seated in its slot Make sure monitor s video cable is properly connected to the computer Inspect monitor s video cable and make sure none of the pins are bent Make sure computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED The LED should either turn ON or OFF after hitting the CAPS LOCK key Missing one of the primary colors RED GREEN or BLUE Inspect the monitor s video cable and make sure that none of the pins are bent Figure 1 Installing and Removing the Swivel Base Figure 3 External Control Knob Figure4 The OSD Message 0060068 Contrast
3. in fire or electric shock Never push any object into the slot on the monitor cabinet It could short circuit parts causing a fire or electric shock Never spill liquids on the monitor e Do not attempt to service the monitor yourself opening or removing covers can expose you to dangerous voltages and other hazards Please refer all servicing to qualified service personnel e To ensure satisfactory operation use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100 240V AC Min 1 5A The wall socket shall be installed near the equipment and shall be easily accessible Attention Disconnect the power cord to stop the power supply to the monitor Plug amp Play DDC1 2B Feature This monitor is equipped with VESA DDC1 2B capabilities according to the VESA DDC STANDARD It allows the monitor to inform the host system of its identity and depending on the level of DDC used communicate additional information about its display capabilities The communication channel is defined in two levels DDC1 and DDC2B The DDC1 is a unidirectional data channel from the display to the host that continuously transmits EDID information The DDC2B is a bidirectional data channel based on the 1 C protocol The host can request EDID information over the DDC2B channel THIS MONITOR WILL APPEAR TO BE NON FUNCTIONAL IF THERE IS NO VIDEO INPUT SIGNAL IN ORDER FOR THIS MONITOR TO OPERATE PROPERL
4. to 56kHz automatically Vertical 50Hz to 120Hz automatically Max Resolution 1024 x 768 Video Dot Rate 65MHz Factory Preset Timings 5 User mode Timings 8 Power Source Universal AC 100 240V 50Hz 60Hz Operating 0 C to 40 C ambient Humidity 10 to 85 relative non condensing Dimension 360 W x 362 H x 387 D mm Monitor amp Base Weight Net 11 5kg Signal Cable Attached Mini D sub 15 Male Plug amp Play DDC1 2B EPA ENERGY STAR On Mode lt 75W Off Mode lt 8W Power consumption 75 Watts Max Preset display area 260mm x 195mm Regulations UL CSA FDA FCC CE Factory Preset Timing Table STANDARD HORIZONTAL ee RESOLUTION FREQUENCY VERTICAL FREQUENCY IBM 720 x 400 VGA 640 x 480 VES 540 x 480 AH 800 x 600 VESA 60 1024 x 768 48 36kHz VESA 85 31 47kHz 70Hz 31 47kHz 60Hz 53 67kHz 85Hz CONNECTOR PIN ASSIGNMENT 15 Pin Color Display Signal Cable PIN NO DESCRIPTION PIN NO DESCRIPTION 1 Red 9 NC 2 Green 10 Ground 3 Blue 11 Monitor Ground 4 Ground 12 DDC Serial Data 5 Ground 13 H Sync 6 R Ground 14 V Sync V Clk 7 G Ground 15 DDC Serial Clock 8 B Ground 5 For DDC
5. CT500G User s Manual Thank you very much for choosing the AOC Color Monitor We recommend that you take a few minutes to read carefully through this brief but comprehensive manual before installing and switching on the monitor Please keep this manual in a safe place for you future reference Plug 8 Play Drivers for the AOC Series Monitors are available at www aocmonitor com CHECKING THE CONTENTS OF THE MONITOR PACKAGE The product package should include the following items 1 Monitor 2 Owner s Manual 3 Power Cord Refer to the Using the right power cord statement 4 Swivel Base FCC Class B Radio Frequency Interference Statement WARNING FOR FCC CERTIFIED MODELS NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of th
6. Caution Don t bend the signal cable otherwise it will break the inner wire Connecting the Power Cord Plug the power cord into the monitor s AC power jack Then plug the power cord into a grounded AC outlet UL approved power strip or the power output socket on your PC Caution If the AC outlet is not grounded install the proper grounding adapter not supplied OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS The power switch is located at front panel of the monitor Press the power switch to tum the monitor on or off The other control knobs are located at the base of the monitor See Figure 3 By changing these settings the picture can be adjusted to your personal preferences e The power cord should be connected e Connect the video cable from the monitor to the video card e To turn the monitor on press the POWER switch to ON position The power indicator will light up e Your monitor features a unique quick switch system which provides a picture within seconds after the monitor is switched on NOTES Do not install the monitor in a location near heat sources such as radiators or air ducts or in a place subject to direct sunlight or excessive dust or mechanical vibration or shock e Save the original shipping carton and packing materials as they will come in handy if you ever have to ship your monitor e For maximum protection repackage your monitor as it was originally packed at the factory e To keep t
7. Y THERE MUST BE A VIDEO INPUT SIGNAL This monitor meets the Green Monitor standards as set by the Video Electronics Standards Association VESA and or the United States Environmental Protection Agency EPA and The Swedish Confederation Employees NUTEK This feature is designed to conserve electrical energy by reducing power consumption when there is no video input signal present When there is no video input signal this monitor following a time out period will automatically switch to an OFF mode This reduces the monitor s internal power supply consumption After the video input signal is restored full power is restored and the display is automatically redrawn The appearance is similar to a Screen Saver feature except the display is completely off The display is restored by pressing a key on the keyboard or clicking the mouse USING THE RIGHT POWER CORD The accessory power cord for the Northern American region is the wallet plug with NEMA 5 15 style and is UL listed and CSA labeled The voltage rating for the power cord shall be 125 volts AC Supplied with units intended for connection to power outlet of personal computer Please use a cord set consisting of a minimum No 18 AWG type SJT or SVT three conductors flexible cord One end terminates with a grounding type attachment plug rated 10A 250V CEE 22 male configuration The other end terminates with a molded on type connector body rated 10A 250V having standard CEE 22
8. e following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio TV technician for help NOTICE 1 The changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Shielded interface cables and AC power cord if any must be used in order to comply with the emission limits The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment It is the responsibilities of the user to correct such interference As an ENERGY STAR Partner Envision Peripherals Inc has determined that this product meets the ENERGY STAR guidelines for energy efficiency WARNING To prevent fire or shock hazard do not expose the monitor to rain or moisture Dangerously high voltages are present inside the monitor Do not open the cabinet Refer servicing to qualified personnel only on PRECAUTIONS e Do not use the monitor near water e g near a bathtub washbowl kitchen sink laundry tub swimming pool or in a wet basement e Do not place the monitor on an unstable cart stand or table If the monitor falls it can injure a person and cause serious damage to the appliance U
9. he monitor looking new periodically clean it with a soft cloth Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution Never use strong solvents such as thinner benzene or abrasive cleaners since these will damage the cabinet As a safety precaution always unplug the monitor before cleaning it ADJUSTING THE PICTURE See Figure 3 1 O CONTRAST Adjust the picture contrast 17 gt RECALL Press RECALL to restore the monitor 2 Q BRIGHTNESS Adjust the picture brightness to factory settings a H CENTER Adjust the horizontal position of the picture 18 e EXIT Close OSD window H SIZE Adjust the picture s horizontal size 4 e a 19 se Select the language as you like V CENTER Adjust the vertical position of the picture 5 6 Ea V SIZE Adjust the picture s vertical size Adjust the picture s horizontal and vertical size T a ZOOM simultaneously 8 Pincushion Adjust the pincushion and barrel 9 O TRAPEZOID Adjust the picture s trapezoid distortion Adjust to compensate the pincushion 0 CI PIN BALANCE Te PARALLELO HOW TO ADJUST A SETTING 1 o GRAM Adjust the picture to be a rectangle 1 Press the Menu to make the OSD window appear See figure 4 7 7 7 2 Press the Brightness or Contrast Knob to change the settings of the current 12 ROTATION Adjust the picture tilt to horizontal p
10. osition function EEE 3 When the OSD window is active it shows the input signal timing The H 6500 K 9300 K ie en 5 a voor i stands for the horizontal frequency and V for the vertical frequency 3 COLOR presents two different color sets on the screen 4 To exit and save select the exit function or leave the monitor alone for 10 TEMPERATURE You can select 9300 K or 6500 K by pressing seconds If you want to adjust any other function repeat steps the Shuttle Knob 24 QO If the 9300 K normal white or 6500 K warmer 14 AD USER COLOR white do not satisfy your desire properly adjust i Red Blue R B GAIN controls to obtain your optimum whiteness level If color impurity occurs when moving or 15 Less swiveling the monitor press the Shuttle Knob and degauss to fix the picture condition Moire is the result of interference between the phosphor layout and the video signal In some cases you may find the moire very noticeable 16 MOIRE REDUCE Press the Shuttle Knob to enter in the moire reduce setting Please adjust the level to the optimum condition Note Too high of a setting will cause the picture to shake SPECIFICATION CRT 38 1cm 15 90 deflection 29mm neck 0 24mm H 0 28mm D dot pitch Viewable Image Size 35 1cm 13 8 diagonal Video 0 7Vpp R G B Analog Separate Sync TTL Level H V sync Positive Negative Scanning Frequency Horizontal 30kHz
11. se only a cart or stand recommended by the manufacturer or sold with the monitor If you mount the monitor on a wall or shelf use a mounting kit approved by the manufacturer and follow the kit instructions Slots and openings in the back and bottom of the cabinet are provided for ventilation To ensure reliable operation of the monitor and to protect it from overheating be sure these openings are not blocked or covered Do not place the monitor on a bed sofa rug or similar surface Do not place the monitor near or over a radiator or heat register Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided The monitor should be operated only from the type of power source indicated on the label If you are not sure of the type of power supplied to your home consult your dealer or local power company e The monitor is equipped with a three pronged grounded plug a plug with a third grounding pin This plug will fit only into a grounded power outlet as a safety feature If your outlet does not accommodate the three wire plug have an electrician install the correct outlet or use an adapter to ground the appliance safely Do not defeat the safety purpose of the grounded plug e Unplug the unit during a lightning storm or when it will not be used for long periods of time This will protect the monitor from damage due to power surges e Do not overload power strips and extension cords Overloading can result
Download Pdf Manuals
Related Search