Chief ER-12\8 racks
Contents
1. side panels A and B See Figure 1 3 Secure rack top C to one side panel using two M7x70mm B Phillips confirmat screws K Do not overtighten See Figure 2 4 Secure the rack bottom D using two M7x70mm Phillips confirmat screws K Do not overtighten See Figure 2 5 Secure upper cross brace G to the front of the side panel using two M7x70 Phillips confirmat screws K See Figure 2 6 Secure lower cross brace H to the bottom of the side panel using one M7x70 Phillips confirmat screws K See Figure 2 7 Install seven caps M to installed confirmat screws See Figure 2 8 Install remaining side panel A to the other side following Steps 3 7 Figure 2 ER 12 8 Installation Instructions 9 Carefully set assembled rack on its side See Figure 3 10 Useremaining sixteen 10 x 5 8 wood screws L to secure four casters J to rack bottom D See Figure 3 11 Install components to rack as desired Figure 3 Installation Instructions ER 12 8 ER 12 8 Installation Instructions GS CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8800 002298 Rev00 2013 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 02 13 USA International Europe Asia Pacific p TI U gt 0 6436 City West Parkway Eden Prai2. INSTALLATION INSTRUCTIONS Economy Rack S CHIEF ER 12 8 Our Mounts Your ER 12 8 Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectivelv Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for everv possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of anv kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiencv of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It is the inst
3. Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis a pointe cruciforme Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl fourche Installation Instructions ER 12 8 DIMENSIONS 15 75 M 4001 7 20 63 863 B 523 9 g 1 219 1 i i 41 94 39 01 10653 pua TE Te 17 63 447 7 1 1 1 i ER 12 8 Installation Instructions TOOLS REQUIRED FOR INSTALLATION 2 C 1 A 1 rack topl right side panel B 1 LC left side panel D 1 rack bottom E 2 Re G 1 12 space rack rail upper cross brace J 4 1 caster ia 78 og a brace L 26 M 14 M7x70mm 5 8 cap Installation Instructions ER 12 8 ASSEMBLV 1 Use six 10 x 5 8 wood screws L to secure two 12 space rack rails E to two side panels A and B See Figure 1 2 Use four 10 x 5 8 wood screws L to secure two 8 space rack rails F to two
4. aller s responsibility to make sure all components are properly assembled and installed using the instructions provided LEGEND WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located within the rack or on top of the rack does not exceed 150 Ibs 68 kg Use with products heavier than the maximum weight indicated may result in instability or collapse of the rack causing possible injury IMPORTANT Minimum spacings between the Accessories and components and the ITC AV Rack Enclosure shall be maintained for safe operation of the equipment when installed in accordance with the National Electric Code ANSI NFPA 70 2008 Operating temperature inside rack shall not exceed 104 F SAVE THESE INSTRUCTIONS Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Phillips Screwdriver Destornillador
5. rie MN 55344 800 582 6480 952 225 6000 877 894 6918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 O S
Download Pdf Manuals
Related Search