Viewsonic VSD221
Contents
1. ViewSonic 4 VSD221 Smart Display User Guide Model No VS15006 Compliance Information Please read before proceeding e Use only the batteries and power adapter provided by the manufacturer The use of unauthorized accessories may void your warranty e Do not store your device in temperatures higher than 50 C 122 F e The operating temperature for this device is from 0 C 32 F to 35 C 95 F FCC Notice The following statement applies to all products that have received FCC approval Applicable products bear the FCC logo and or an FCC ID in the format FCC ID GSS VS15006 on the product label This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation This mobiledevice has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequencyenergy and if not installed and used in accordance with the instructions may cause harmful interferenceto radio communications However there is no guarantee that interference will not occur in a particular installation If this2. DO NOT use the device in the rain Please check with your Local Authority or retailer for proper disposal of electronic products The device and the adapter may produce some heat during normal operation or charging To prevent discomfort or injury from heat exposure DO NOT leave the device on your lap POWER INPUT RATING Refer to the rating label on the device and be sure that the power adapter complies with the rating Only use accessories specified by the manufacturer DO NOT use a pen or any sharp object to tap the screen Clean the touch screen with a soft cloth If needed dampen the cloth slightly before cleaning Never use abrasives or cleaning solutions Always power off the device to install or remove external devices that do not support hot plug Disconnect the device from an electrical outlet and power off before cleaning the device DO NOT disassemble the device Only a certified service technician should perform repair The device has apertures to disperse heat DO NOT block the device ventilation the device may become hot and malfunction as a result Users have to use the connection to USB interfaces with USB 2 0 version or higher PLUGGABLE EQUIPMENT the socket outlet shall be installed near the equipment and shall be easily accessible Copyright Information Copyright ViewSonic Corporation 2013 All rights reserved Android is a trademark of Google Inc Use of this trademark is subject to Go
3. The right side of the system bar displays current time and status buttons Area Descriptions Displays the current time ee Notification button informs you of new e mail messages Notification area at and so on Touch it for viewing Show you the current state of your device just like Status area network connections 3 5 1 Managing Notifications You can touch Time area to pop up status configuration screen to disable enable the Notification function Or touch the notification button directly to view the information Fi otifications ettings e Touch notification button to view the detail e Swipe left or right on the notification message to remove it e Touch Time area to view all current notifications 3 5 2 Status Detail You can touch Time area to pop up status Detail screen to configure device settings and Wi Fi And touch any other area of the screen i to close the Status Detail ee Q Notifications Settings e View the detail about date and time e View the state of network connections e Touch Settings to open Settings configuration screen About Your VSD221 Smart Display 3 6 Customizing Your Home Screen 3 6 1 Add an Item Shortcut e Touch the Home button to go back the central Home screen e Drag on the screen horizontally to select a Home screen where you want to add the item e Touch the Apps button located on the upper right corner of your screen e On the Apps screen
4. display the chemical symbol Hg Cd or Pb then it means that the battery has a heavy metal content of more than 0 0005 Mercury or more than 0 002 Cadmium or more than 0 004 Lead European Union Regulatory Conformance The equipment complies with the RF Exposure Requirement 1999 519 EC Council Recommendation of 12 July 1999 on the limitation of exposure of the general public to electromagnetic fields 0 300 GHz This equipment meets the following conformance standards EN301489 1 EN301489 17 EN55022 24 EN60950 1 EN300328 We hereby declare that this Wi Fi amp Bluetooth radio is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC Declaration of ROHS2 Compliance This product has been designed and manufactured in compliance with Directive 2011 65 EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment ROHS2 Directive and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee TAC as shown below Proposed oe Actual Concentration Concentration Lead Pb Mercury Hg Cadmium Cd 0 01 lt 0 01 Hexavalent Chromium Cr6 Polybrominated biphenyls PBB Polybrominated diphenyl ethers 0 0 PBDE oa o k ae Certain components of products as stated above are exempted under the Annex III of the ROHS2 Directives as n
5. 2 Select the account where you want to add this contact such as your Gmail account e This area shows the account in which the new contact is stored e Take photo Touch to take a photo to use as the contacts visual call er ID e Select photo from Gallery Touch to select a photo from the Gallery application to use as the contact s visual caller ID e Enter the contact information using the on screen keyboard You can tap on the Add another field tab to add more information e Touch to replace a default information label with another label that you can choose from the list For example you can change the label from Home phone number to Mobile phone number e Touch to add a new item to the current information category For ex ample you can add a second phone number e Touch to remove an item from the current information category e Touch to fill more information about the contact e Touch to display more options e Touch Cancel to return to your Contacts list e Touch Done to save the new contact to your Contacts list e Touch to return to your Contacts list Using Your VSD221 Smart Display 4 1 2 Find a contact To locate a contact you can either aes e Flick the All tab contacts list on the up lt per left of screen until you find the con us tact Or drag the scroll bar on the left of the screen to scroll through the con tacts list e Touch a Find contacts on the upper right of screen and then typ
6. cloth Problems Causes Solutions _ Unable to send or receive text messages Unable to send or receive e mail The signal strength is not strong enough The Internet connection or the e mail setting is not configured properly Unable to connect to the network Poor signal Try moving to a different location for better signal reception Check your network connection and confirm with your e mail service provider if your e mail setting has been configured correctly You are not within the Check the service area with network s service area your service provider Move to an open space or if you are inside a building move closer to a window Troubleshooting 8 3 Other Problems Problems Solutions No power Press and hold the power button for at least three seconds Page 12 Section 2 3 if the LED does not light green with the device booting up then Ensure that the power adaptor is plugged in to a suitable power socket Ensure that the DC connector is fully inserted into the correct socket on the rear of the VSD221 located under the cover see page 8 and 11 Check the power socket with another device i e table lamp If there is still no power then contact ViewSonic support or the Reseller from whom the device was purchased No display Check external HDMI device and connections Restart by pressing and holding power button App doesn t Check with App author function Check WiF
7. 7 1 1 Create a screen unlock pattern A Touch the Home button Apps button Settings Security 2 Touch Screen Lock section Pattern 3 Read the instructions on the screen and study the animated example of how to draw a pattern Then touch Next when you are ready to draw your own pattern 4 Drag your finger to draw the unlock pattern by connecting at least four dots in a vertical horizontal and or diagonal direction Take your finger off the screen when a pattern is drawn e You must touch and drag your finger on the screen to create the pattern Protecting Your VSD221 Smart Display 1 The device records the pattern if it is correctly drawn Touch Continue 2 Draw the pattern again as prompted and then touch Confirm e If you want to change your unlock screen pattern you need to draw the old pattern to confirm before creating a new pattern 7 1 2 Change unlock pattern settings 1 2 7 2 Touch the Home button Apps button Settings Security Once the pattern setting is enabled under the Screen lock Unselect Make pattern visible check box if you do not want the lines of the unlock pattern to display on the screen when you draw it Disable the screen unlock security Touch the Home button Apps button Settings Security select None to disable screen unlock security Protect Your Device Data with a PIN Touch the Home button Apps button Settings Security Touch Screen Lock section PI
8. VSD221 to a LAN network via RJ 45 cable on LAN connector or set up a Wi Fi connection 5 1 1 Wi Fi connection A Touch the Home button Apps button Settings Wi Fi to enable Wi Fi function by touching ON The device scans for available wireless networks 2 Touch Wi Fi settings The network names and security settings Open network or Secured with WEP WPA WPA2 WPS of discovered Wi Fi networks display in the Wi Fi networks list 3 Flick the list and touch to select a Wi Fi network you want to connect to Enter a password if necessary then touch Connect to connect to the Wi Fi network Connect to a network protected by Wired Equivalent Privacy WEP Wi Fi Protected Access WPA WPA2 or Wireless Protected Setup WPS you must enter the WEP WPA WPA2 WPS security key to obtain authorized access to the network The next time your device connects to a previously accessed secured wireless network you will not be required to enter the WEP WPA WPA2 WPS key again unless you reset your device to its factory default settings Internet 5 1 2 Check the current Wi Fi network connection From the status area of the system bar When your device is connected to a wireless network the Wi Fi icon in the status area of the system bar indicates the signal strength number of bands that light up If Settings Wi Fi Network notification is enabled the icon appears in the notifications area of the system bar as th
9. caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Canada Statement This device complies with Industry Canada licence exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Caution Exposure to Radio Frequency Radiation To comply with RSS 102 RF exposure compliance requirements a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons Pour se conformer aux exigences de conformite CNR 102 RF exposition une distance de separation d au moins 20 cm doit tre maintenue entre l antenne de cet appareil et toutes les personnes CE Conformity for European Countries The device complies with the EMC Directive 2004 108 EC and Low Voltage Directive 2006 95 EC R amp TTE Directive 1999 5 EC Following information is only for EU member states The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2002 96 EC WEEE K The mark indicates the requirement NOT to dispose the equipment as unsorted municipal waste but use the return and collection systems according to local law If the batteries accumulators and button cells included with this equipment
10. hour or minute to flick to the desired value 2 Touch the AM PM field if the 12 hour format is in use 3 Touch Done to confirm the time Set time zone select a city or region that represents the time zone for your device Touch the Menu button to sort the time zone list alphabetically or by time zone Use 24 hour format Clear this check box to display the time in 12 hour format Select date format select the format to be used for displaying the date 6 4 Language amp Input Settings Set the language of the display text Touch the Home button Apps button Settings Language amp input Language By default the Language is set to English NO select a language of your choice from the list that appears eS A Spell checker function is also supported Tap the Spell checker check box to enable this function A For extra defined wording touch the Personal dictionary then touch ADD on the upper right of screen to add new defined wordings to your personal dictionary Set the Keyboard amp Input A Touch the Home button Apps button Settings Language amp input Keyboard amp input methods 2 To enable a setting touch the setting option to select the check box to disable a setting touch the setting option to clear the check box 3 You can also touch setting icon for each selection for advanced configurations e Here you can also configure the speech of voice test output and pointer Cu
11. you read the documentation of the pairing device to check if it requires a default password 6 When the pairing is successful paired but not connected devices are displayed under the PAIRED DEVICES 1 The message indicating successful pairing may vary depending on the type of the paired device 2 Pairing is a one time process Once your device successfully pairs with another device your device recognizes that device without the need to re enter the password Using Your VSD221 Smart Display 4 6 3 Terminate a pairing partnership Touch the Home button Settings Bluetooth Under the Paired devices section touch the icon next to a paired device Touch Unpair to erase all pairing information with that device You need to re enter the password if you want to restore a Bluetooth connection to that device 4 6 4 Change your device s Bluetooth name 1 Ensure that you have turned on Bluetooth on your device Icon in the status area of the system bar indicates that Bluetooth is enabled Touch the Home button Settings Bluetooth Tap the Menu button on the upper right hand side of the screen to rename your smart display Enter a name to identify the device when you connect using Bluetooth Tap Rename Your device s Bluetooth name has been changed Internet o Internet 5 1 Connecting to the Internet To browse the web and access web based utilities such as instant messaging you can connect
12. 77 CON 10 LINEAS Electroser Av Reforma No 403Gx39 y 41 97000 M rida Yucatan Tel 01 999 925 19 16 Other places please refer to http www viewsonic com la soporte index htm Mexico Latin America Peru www viewsonic com la T 0800 54565 soporte viewsonic com Macau www hk viewsonic com T 853 2870 0303 service hk viewsonic com Middle East ap viewsonic com me Contact your reseller service ap viewsonic com T 1 800 688 6688 English PUET ORIGO www viewsonic com T 1 866 379 1304 Spanish service us viewsonic com Islands F 1 909 468 3757 soporte viewsonic com Singapore Malaysia www viewsonic com sg T 65 6461 6044 service sg viewsonic com Thailand South Africa ap viewsonic com za Contact your reseller service ap viewsonic com T Toll Free 1 800 688 6688 United States www viewsonic com T Toll 1 424 233 2530 service us viewsonic com F 1 909 468 3757 Limited Warranty ViewSonic Smart Display What the warranty covers ViewSonic warrants its products to be free from defects in material and workmanship under normal use during the warranty period If a product proves to be defective in material or workmanship during the warranty period ViewSonic will at its sole option repair or replace the product with a like product Replacement product or parts may include remanufactured or refurbished parts or components The replacement unit will be covered by the balance of the time re
13. N On the Choose your PIN screen appears enter a PIN in the textbox Your PIN must be 4 characters at least Touch Continue to proceed Enter the PIN again to confirm Protecting Your VSD221 Smart Display 6 Touch OK 7 3 1 Disable or change PIN Touch the Home button Apps button Settings Security 2 Touch Screen Lock section 3 Enter the PIN code you have configured and then touch Continue 4 select None secured to disable the PIN select PIN to change PIN code 7 4 Protect Your Device Data with a Password Touch the Home button Apps button Settings Security 2 Touch Screen Lock section Password 3 On the Choose your password screen appears enter a password in the text box A valid password consists of at least 4 characters and contains at least one letter 4 Touch Continue to proceed 5 Enter the password again to confirm 6 Touch OK 7 4 1 Disable or change the password Touch the Home button Apps button Settings Security 2 Touch Screen Lock section Protecting Your VSD221 Smart Display 3 Enter the password you have configured Select None secured to disable the password select Password to change the password e Once the screen lock is secured with Pattern FaceUnlock Pin and Password the Au tomatically lock will appear under Screen lock By default it is set to 5 seconds after entering sleeping mode 7 5 Power Saving Feature In order to save energy this device s
14. OSD configurations Screenshot Time Bluetooth WiFi and other functions system bar Ho About Your VSD221 Smart Display tems Descriptions SSS Return to the previous screen or option This button will indicate you to go back to Home central Home screen at any time Touch this button to show you a list of images Recent about the applications you have accessed Applications recently You can touch the listed image to open the applications Touch this to open screen display related configurations including Volume Brightness Contrast SRS HDMI and restore to Default OSD values and so on OSD can only be operated with touch screen and will not respond to mouse input 71 9 08 Touch Bluetooth button on the right of system bar to pop up current system configuration screen In the configuration screen you can 3 Bluetooth Configure Wi Fi Review all items in the Settings Configure Notifications to enable or disable Magnify the Time viewing To add a shortcut or widget to the Home Home screen touch and hold the icon you want screen to add The icon will appear on the Home screen Drag it to a suitable place You can add a shortcut button to the Home ehancuis screen by touching and holding the specified icon This icon allows you to open a shortcut item quickly Touch the Apps button to show all of the eee Apps applications installed on your device Widgets are small applications that reside on Widg
15. arch by voice 1 Touch the microphone amp that appears beside the search box 2 say the name or keyword of the item you want to search 3 The browser with matching web links opens Using Your VSD221 Smart Display 4 4 Managing Your Device Settings 4 4 1 Check storage spaces Touch the Home button Apps button Set tings Storage The screen displays the total and available space on the device USB stor age and SD card Erase unwanted application data 1 Touch the Home button Apps button Settings Apps Touch the application whose cache or data you want to remove 3 Touch Clear data under Storage to erase unwanted application data touch Clear cache under Cache to erase unwanted cache 4 4 2 Remove the SD card safely Touch the Home button Apps button Settings Storage Using Your VSD221 Smart Display 2 Touch Unmount SD card under the SD Card section 3 Press and hold the Power button until the Power off menu appears Then touch OK to turn off the device 4 Pull out the compartment cover and then remove the SD card from your device e Removing the SD card while the device is working may cause data loss or result in ap plication errors We suggest you unmount the SD card before removing it 4 4 3 Erase all data from your device 1 Touch the Home button Apps button Settings Backup amp reset 2 Touch Factory data reset tablet 3 Touch Reset smart display t
16. ceceeeeeeeees 31 6 4 Language amp Input Settings cc cecececceeeeeeeeeeeeeeeeees 32 65 OSD Coi gt 11 919 en ee er ener 33 6 5 1 Adjustment Bars ccccceccseceeeceeceeeeeeseeeeeenes 33 6 5 2 Functions ButtOns cccccc ccc eeeceeeeeeeeseeeeeeeees 30 O98 SD NOU CC e ierre a EE E EEA 34 7 Protecting Your VSD221 Smart Display 7 1 Protect Your Device Data with a Screen Unlock Pattern 35 7 1 1 Create a screen unlock pattern c ceeeeeees 35 7 1 2 Change unlock pattern settings cceee 36 7 2 Disable the screen unlock security cee ceee sees eee eeees 36 7 3 Protect Your Device Data with a PIN cece eee ees 36 7 3 1 Disable or change PIN ccccceccseeceeeeeeeeeees 37 viii Table of Contents 7 4 Protect Your Device Data with a Password 00 37 7 4 1 Disable or change the password a n0n00n00000nn 37 7 5 Power Saving Feature cccccccecssecsescceecesecseeeeeeasesaees 38 7 6 Power Management Information ccccceceeeeeeeeeeees 38 8 Troubleshooting 8 1 Touch Screen Problems ccccccccecceccececcecceccaceuesueas 39 8 2 Messaging Problems ccccccseccecceecceeceeceeeceeseesaeeees 39 8 3 Other ProbleMs ccc ccc ccccceccececccccccccccccececceacecesuenueas 40 9 Appendix Specification 20 cece cec ccc cc ccc eeceeeeeeeeeeeeeeeeeeeeeeeeeaeeee
17. condition Delta Electronics N A electric power consumption and average Inc active efficiency of external power suppliers Syph Hn August 23 2012 Sophia Wu Compliance Manager Date ViewSonic Corporation F n gt my Ou ViewSonic
18. d the power button more than 4 seconds 2 When the power off menu appears touch OK About Your VSD221 Smart Display 3 About Your VSD221 Smart Display 3 1 Touch Screen The main way to control the device is using your finger to touch the sensitive surface of the screen directly You can manipulate icons buttons menu items on screen keyboard and other items on the touch screen with below methods Methods Descriptions _ S Simply touch the items with you finger Act on items on the screen including application and settings icons Type letters and symbols using the on screen keyboard Press the on screen buttons Touch and Touch and hold an item on the screen by touching it without Hold lifting your finger until an action occurs Drag Touch and hold an item then move the item with your finger until reaching the target position Move an item on the screen Scroll through Home screens web pages lists entries photo thumbnails contacts and so on Swipe or Slide Quickly move your finger across the surface of the screen without pausing when you first touch it Zoom Out Move two fingers close together on the screen to reduce the view of an image or web page Zoom In Move two fingers apart on the screen to enlarge the view of an image or web page 3 2 Applications Widgets and Shortcuts The soft buttons or icons offer a variety of functions and shortcuts On the Home screen it is your starting point to acce
19. e device discovers an accessible Wi Fi network within range From the Wi Fi network 1 2 Touch the Home button Apps button Settings Wi Fi Touch the Wi Fi network that the device is currently connected to labeled Connected A screen opens displaying the Wi Fi network s name status security information signal strength link speed and IP address If you want to disconnect the Wi Fi network from your device touch Forget on this screen You will need to configure the Wi Fi settings again if you want to restore connection to this wireless network 5 1 3 Connect to another Wi Fi network 1 2 3 4 Touch the Home button Apps button Settings Wi Fi The detected Wi Fi networks are displayed in the Wi Fi networks list Start a new search for available Wi Fi networks on the Wi Fi settings screen touch the Menu button on the upper right of screen scan Flick through the Wi Fi networks list and touch the name of the network you want to connect to If the wireless network you want to connect to is not on the list tap the sign on the upper right hand side to add your Wi Fi network Enter the Wi Fi network settings and then touch Save Internet 5 2 Synchronizing Your Google Data Through a web connection your device can synchronize your Google data including Gmail calendar and contacts with your com puter or any other device that you use to ac cess your Google account Select the app
20. e either the contact s full name or only the first let ters of it into the text box The screen displays the matching contacts User Once the contact is located touch the contact s entry to view the contact s details 4 1 3 E mail or send a message to a contact 1 On the contacts list find a desired contact 2 Touch the contact entry to view the contact details and then touch to send e mail using the e mail accounts you have set up on your device or touch it to send a message Edit a contact 1 On the contacts list find a desired contact 2 Touch the contact entry to view the contact details 3 Touch 2 to edit the contact details Touch Done to save the changes Using Your VSD221 Smart Display Share a contact 1 On the contacts list find a desired contact 2 Touch the contact entry to view the contact details 3 Touch the Menu button on the upper right of screen then select Share contact 4 From the Share contact via menu that appears select the way you want to share the contact information with your friends such as through Bluetooth or Gmail Join contacts Since your device can synchronize with a variety of accounts when synchronizing con tacts from these accounts with your device you may have multiple contacts for the same person Joining contacts allows you to view all the contact s numbers addresses and so on in one single contact entry On the Contacts list find a d
21. e the SD card safely cccceceeeeeee eee 21 4 4 3 Erase all data from your device ccceeeee eee 22 4 5 Connecting to HDMI compliant Devices via Micro HDMI MDU aeree E E 22 4 6 Bluetooth Connection s nonnenonnsnnnnennnrensnnsrrnrerrrrsrenrne 23 4 6 1 Turn on Bluetooth and make the device GISCOV GTDC tecaiccsorereatesanenes lt susnenseatednemecsraneiees 24 4 6 2 Pair with a Bluetooth device ccccec cee eeee eens 24 4 6 3 Terminate a pairing partnership ccecee 20 4 6 4 Change your device s Bluetooth name 25 5 Internet 5 1 Connecting to the Internet 0nnannannannennnnnnnnnnnnnnnnnnnnnn 26 5 1 1 Wi Fi connection ere spas icacesunsscsinnconnstiapnacateeeeasnpne des 26 5 1 2 Check the current Wi Fi network connection 2 5 1 3 Connect to another Wi Fi network 0068 27 9 2 Synchronizing Your Google Data ccccecceeeeeeeeeee ees 28 5 3 Video CM adic cen tcetercescenesetn cacti nratiteecneenedatace wnaweseeieeccinteess 28 6 Customizing Your VSD221 Smart Display Bel Display SOWING 6 vce cccecrettceeeeeseseercemostesaeeeeieneceneteeseusesea 30 6 2 Sound and Ringtone SettingS ec ceecceeeeeeeeeeeeees 30 6 2 1 System SC TING See reece sete apces oa ceunteedyentiueeeseeeeesoete 31 6 2 2 Notifications SettingS ccccccecceceseeeeeeeeeeeeees 31 6 3 Date Time and Time ZOne 0c cece ce ccccecececce
22. eeeeeeeeeaeeeeeneeaees 41 VSD221 Smart Display Features 1 VSD221 Smart Display Features This section introduces you to the features of your Smart Display e The features or applications described in this User s manual may vary depending on the device model purchased Front View Google No Components Descriptions Z o Z o o Used for receiving audio or audio input USB Ports x 2 Used for keyboard mouse Flash Disk or printer connections Power Button Press and hold to power on off the device Press and Hold about 2 3 seconds to turn on the power green light Press about 0 5 seconds to let the system enter the power saving mode sleep mode orange light or wake up the system from the power saving mode Press about 3 4 seconds to pop up a system shutdown or not dialog screen Press about 10 seconds to force the system shutdown LED Indicator Indicates the status of power power on off or power saving VSD221 Smart Display Features No Components Earphone Jack Connect to earphone or headset Micro USB Port Connect to windows computer for data transferring Need MTP driver including menu items applications buttons keyboard and so on i Front Panel Used for taking a front picture just the same as a self Touch Screen Touch the screen to control the on screen configurations Camera portrait Used for making video calls with supportive web applications such a
23. equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna eIncrease the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void theuser s authority to operate the equipment The antenna s used for this transmitter must not be colocated or operating in conjunction with any otherantenna or transmitter The device was tested and complies to measurement standards and procedures specified in FCC OET Bulletin 65 Supplement C FCC SAR Information This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment End users must follow the specific operating instructions for satisfying RF exposure compliance This transmitter must not be co located or operating in conjunction with any other antenna or transmitter This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body The users manual or instruction manual for an intentional or unintentional radiator shall
24. esired contact Touch the contact entry to view the contact details and then touch Edit on the upper right of the screen Then touch the Menu button on the upper right of the screen Join aO N From the Join contacts list touch another contact to link and then touch Done The joined contact s information is displayed with the original Contacts settings Using Your VSD221 Smart Display In People touch the Menu button on the device or the Menu button on the screen Settings Descriptions _ S Accounts Contacts stored on your device can besynchronized NOTE If you want to with a computer using Mobile Sync contacts stored synchronize individual on your personal e mail account such as Gmail can data manually clear Auto be synchronized through an Internet connection sync and then from your To select the data to synchronize account touch a data item 1 Select Background data to make all the sync to start synchronization of options available that data 2 Select Auto sync to let the deviceautomatically While data is syncing the synchronize the selected data in your Twitter sync icon appears on the account or e mail account which may include option of the data being Twitter contacts and data or Calendar Contacts synced Gmail and Picasa WebAlbums data e To select the data to sync from your e mail account 1 Touch your e mail account to open the Data amp synchronization list 2 Select the da
25. ets the Home screen to provide quick access to information gt fel al Use voice input as an alternative to text entry Voice Input via keyboard oe Flick or drag the screen horizontally until the Navigation oo desired Home screen is displayed 4 Eq C About Your VSD221 Smart Display 3 4 Navigation buttons On the left of system bar you can find the navigation buttons described as below Buttons Descriptions O Z o O o In the OSD configuration screen drag the slider bar to adjust Volume Brightness and Contrast to your OSD OSD Here you can also configure the SRS and HDMI functions or touch Default to restore the factory default values A short cut way for you to open recent applications you Recent Apps have accessed Select and touch one of the images from the list to open the application directly Touch this button to go to the central Home screen when viewing other Home screens Touch this button to go back to the last Home screen you have viewed when launching any functions on the device Or touch this button again to go back to central Home screen Touch this button to go back to the previous screen or option Back If the on screen keyboard is displayed the button changes to Touch it to close the on screen keyboard Screehshot Tap this button to capture an image of your screen About Your VSD221 Smart Display 3 5 Notifications and Status
26. hase Date Product disposal at end of product life ViewSonic respects the environment and is committed to working and living green Thank you for being part of Smarter Greener Computing Please visit ViewSonic website to learn more USA amp Canada http www viewsonic com company green recycle program Europe http www viewsoniceurope com uk support recycling information Taiwan http recycle epa gov tw recycle index2 aspx Table of Contents Table of Contents 1 VSD221 Smart Display Features 1 1 Installing wall mount bracket cc ccc ccecceeceeeeeeeeeeeeeees 3 2 Set Up Your VSD221 Smart Display 2 1 Connection cesserceveyacacsecsconaconnnterenmmuacnnedspumarenrsdiel evobdencconadeons 4 2 2 Get Your Smart Display Ready for Use c eee 4 2 3 Turn On Your Device ccceccecc sce eee eee eece eee eeeeeeeeneeeeeeneeaes 6 2 4 Turn Off Your Device 1 2 2 cceccecc eee eee cece eee eeeeeeeeneeeneenenaees 6 3 About Your VSD221 Smart Display Sek WOME SCION poepen EEE NEEE E EEES T 3 2 Applications Widgets and Shortcuts cceceeeeeeee eee T 3 3 Home Screen 2 0 ce ccec cece ecc eee eeeeeceeeeeeeeseeceeeeeceseeeeeeseneeeesaees 8 3 4 Navigation DUttONS cc eccccceeeceeceee esse eeeeeseeseeeaeeaes 10 3 5 Notifications and SIAUS vacntcomonsrccaasuscsipiutioderanestensenuecsieess 11 3 5 1 Managing Notifications c cece cece eeeeeeeeeeee es 11 3 5 2 Status Detail wsiensca
27. i settings try Ethernet if available Check volume level setting 9 Appendix Specification LCD Spec Size Resolution White Luminance Contrast Ratio Response time Viewing Angle System Operating System CPU system Memory Storage WLAN Bluetooth Camera Microphone LED Indicator Power Switch I O ports Touch screen Touch controller Speakers Adapter DC Power Consumption Power Save Stand VESA mount Dimension Weight Appendix 54 6 cm 21 5 1920x1080 250 200 Max typ 1000 700 typ min oms typ 170 160 horizontal vertical Android Jelly Bean 4 1 TI OMAP 4470 Dual core ARM Cortex A9 1 5GHz DDR2 1GB eMMC 8GB 802 11b g n Bluetooth V2 1 Front MIPI 1 3M HD Internal MIC x1 digital type Green on Orange saving One standby power button power on off suspend resume HDMI x 1 Micro type USB x 2 USB x 1 Micro type supports OTG 3 5mm Headphone out LAN RJ45 supports 10 100 Mbps DC Jack ID 1 7mm OD4 0mm SD card slot Micro type Optical touch type with glass One touch amp Gesture IW x2 Input 100 240Vac 50 60HZ 1 2A or 1A Output DC Jack 19V 2 1A 40W max SOW typ Standby mode lt 1W Off mode lt 0 5W Photo frame type Optional 512 8 mm L x 353 mm H x 24 8mm W Gross 5 8kg Net 4 8Kg Appendix Operation environment Temperature 0 C 40 C Humidity 5 85 Air pressure 86 106 Kpa Storage environmen
28. idental consequential or otherwise 3 Any claim against the customer by any other party 4 Repair or attempted repair by anyone not authorized by ViewSonic OTA update disclaimer ViewSonic Corporation assumes no liability for any errors or omissions in the information displayed This firmware update is intended for ViewSonic smart display ViewSonic assumes no liability for data loss or any damages caused as a result of any updates made on any device or damage to or failure of other equipment to which the products are connected whether incidental consequential or otherwise You agree to take full responsibility for all files and data and to maintain all appropriate backup of files and data stored on any device prior to performance of any update Users shall be responsible for obtaining the necessary rights to access and use any third party content ViewSonic assumes no liability for the performance availability and use of third party products and services Corporate names and trademarks mentioned herein are the property of their respective companies Copyright 2013 ViewSonic Corporation All rights reserved 4 3 ViewSonic Smart Display Warranty SD_LW01 Rev 1A 08 21 12 Manufacturer s Declaration of Conformity 3 The ViewSonic brand Product VS15006 Model name VSD221 has been designed and manufactured in accordance with the Directive 1999 5 EC of European Parliament and the Council on Radio equipment and Telecommunication Term
29. inal equipment The product is in conformity with the following standards and or other normative documents 1 EMC Standard Testing Body Report No EN55022 2010 Limits and methods of measurement of radio Burea Veritas CE120605D14A interference characteristics of information Consumer technology equipment Products EN55024 2010 Information Technology Immunity standard Services H K Ltd EN61000 3 2 2009 Disturbances to residential supply system Taoyuan Branch Part 2 Harmonics EN61000 3 3 2008 Disturbances in supply systems caused by household appliances and similar electrical equipment Part 3 Voltage fluctuations Part 1 Common technical requirements 2 HEALTH amp SAFETY OO me OOOO Oo EN60950 1 2011 Information technology equipment Safety UL DEMKO DK 27650 UL Part 1 General requirements EN50332 1 2000 Sound system equipment Headphones EN50332 2 2003 and earphones associated with portable audio equipment Maximum sound pressure level measurement methodology and limit considerations Part 1 General method for one package equipment Part 2 Matching of set with headphones if either or both are offered separately EN62311 2008 Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields 0 Hz 300 GHz EN62209 1 2006 Procedure to determine the specific absorption rate SAR for hand held devices used in close proximity to the ear freque
30. ing essential requirements under article 3 2 of the R amp TTE Directive EF 2012 70011 Global System for Mobile N A communication GSM Harmonized EN for mobile stations in the GSM900 and GSM1800 bands covering essential requirements of article 3 2 of the R amp TTE directive 1999 5 EC Eletromagnetic compatibility and Radio spetrum Matters ERM Base Stations BS and User Equipment UE for IMT 2000 Third Generation cellular networks Part 2 Harmonized standrad for IMT 2000 CDMA Direct Spread UTRA FDD UE covering essential requirement of article 3 2 of the R amp TTE Directive Eletromagnetic compatibility and Radio N A spetrum Matters ERM Base Stations BS and User Equipment UE for IMT 2000 Third Generation cellular networks Part 1 Harmonized EN for IMT 2000 introduction and common requirements covering the essential requirements of article 3 2 of the R amp TTE Directive Electromagnetic compatibility and Radio N A spectrum Matters ERM Short range devices Radop equipment to be used in the 1GHz to 40GHz frequency range Part 1 Technical characteristics and test methods Part 2 Harmonized EN covering essential requirements of article 3 2 of the R amp TTE Directive 3 ErP Directive 2009 125 EC Title EC 1275 2008 Eco design requirements for standby and Quanta Computer off mode electric power consumption of electrical and electronic household and office equipment EC 278 2009 Eco design requirements for no load
31. l or consequential damages resulting from furnishing this material or the performance or use of this product In the interest of continuing product improvement ViewSonic Corporation reserves the right to change product specifications without notice Information in this document may change without notice No part of this document may be copied reproduced or transmitted by any means for any purpose without prior written permission from ViewSonic Corporation Intellectual Property Right Information Right to all technologies and products that comprise this device are the property of their respective owners This product has an Android platform based on Linux which can be expanded by a variety of Java Script based application SW Google the Google logo Android the Android logo Gmail and YouTube are trademarks of Google Inc Bluetooth and the Bluetooth logo are trademarks owned by Bluetooth SIG Inc Java JME and all other Java based marks are trademarks or registered trademarks of Sun Microsystems Inc in the United States and other countries microSD is a trademark of SD Card Association Product Registration To meet your future needs and to receive any additional product information as it becomes available please register your product on the Internet at www viewsonic com For Your Records Product Name VSD221 ViewSonic Smart Display Model Number VS15006 Document Number VSD221_ UG ENG Rev 1C 10 16 13 Serial Number Purc
32. lications to synchronize Touch the Home button Apps button Settings ACCOUNTS 2 In the ACCOUNTS section tap the icon to check the box to enable all the sync options Such as Sync Calendar Sync Contacts Sync Gmail Sync Picasa Web Albums 3 If you want to add an account to be synchronized tap on Add Account on the left of the screen under the account you want to synchronize e While data is syncing the sync icon appears on the option of the data being synced 5 3 Video Chat Equipping with a front webcam and a microphone VSD221 allows communication with other users on the Internet VSD221 supports various video chat apps from Google Play By default Google Talk is the most simple video chat application for Android devices and pre installed already Here s a short list of what you will need to use the video chat function of Google Talk e VSD221 e Google Account e People to chat with who also have a Google account and have been added into your Google Talk friend list Internet How to begin 1 Authenticate your Google account You can do this by opening up Google Talk and then signing in to your Google Account Before using video chat you must first sign in to your Google account 2 Invite the person Open Google Talk application Locate to the person in your Google Talk friend list who you want to invite to the video chat Make sure that the friend who you want to chat with is online Then ta
33. maining on the customer s original limited warranty ViewSonic provides no warranty for the third party software included with the product or installed by the customer How long the warranty is effective ViewSonic Smart Display products are warranted for between 1 and 3 years depending on your country of purchase for all parts including the light source and for all labor from the date of the first consumer purchase User is responsible for the backup of any data before returning the unit for service ViewSonic is not responsible for any data loss Who the warranty protects This warranty is valid only for the first consumer purchaser What the warranty does not cover 1 Any product on which the serial number has been defaced modified or removed 2 Damage deterioration or malfunction resulting from a Accident misuse neglect fire water lightning or other acts of nature unauthorized product modification or failure to follow instructions supplied with the product b Repair or attempted repair by anyone not authorized by ViewSonic c Causes external to the product such as electric power fluctuations or failure d Use of supplies or parts not meeting ViewSonic s specifications e Normal wear and tear f Any other cause which does not relate to a product defect 3 Any product exhibiting a condition commonly known as image burn in which results when a static image is displayed on the product for an extended period
34. n e Some wallpapers allow you to change the wallpaper color ex Magic smoke If Settings displays during the changing wallpaper touch it and on the top of screen will display Tap to change touch the screen to configure the wallpaper color Tap the screen to cycle through the different colors e You can touch Back button to go back previous screen without renew any changed settings e All Home Screens share the same background You cannot set different wallpapers for individual Home Screen panels 3 7 Navigating the Applications You can find applications available on your device in the All Apps menu 3 1 Apps screen Open the Apps screen You can access Apps screen from any Home screen by touching the Apps button located on the upper right corner of your screen The Apps screen contains all of the applications installed on the device including those you have downloaded Navigate pages of applications Flick the Apps screen horizontally and touch an application to launch it Close the Apps Screen Touch the Home button on the system bar to go back the central Home screen About Your VSD221 Smart Display 3 2 Application Shortcuts To quickly launch applications on the Home screen you can add shortcuts for frequently used application to the Home screen For more information please refer to 3 6 Customizing Your Home Screen Use the shortcut to open an application 1 Touch the Home b
35. ncy range of 300 MHz to 3GHz EN62209 2 2010 Human exposure to radio frequency fields from hand held and body mounted wireless communication devices Human models instrumentation and procedures Procedure to determine the specific absorption rate SAR for wireless communication devices used in close proximity to the human body frequency range of 30MHz to 6GHZz 3 SPECTRUM Standard Testing Body Report No EC 2012 70005 EN301489 1 V1 8 1 EN301489 17 V2 1 1 EN300328 V1 7 1 EN301511 V9 0 2 EN301908 2 V4 2 1 EN301908 1 V4 2 1 EN300440 1 V1 6 1 EN300440 2 V1 4 1 Electromagnetic compatibility and Radio spectrum Matters ERM Electromagnetic Compatibility EMC standard for radio equipment and services Part 1 Common technical requirements Part 17 Specific conditions for Wideband data and HIPERLAN equipment Part 24 Specific conditions for IMT 2000 CDMA Direct Spread UTRA for Mobile and portable UE radio and ancillary equipment Part 3 Specific conditions of Short Range Devices SRD operating on frequencies between 9kHz and 40GHz Part 7 Specific conditions for mobile and portable radio and ancillary equipment of digital cellular radio telecommunications systems GSM and DCS Electromagnetic compatibility and Radio spectrum Matters ERM Wideband transmission systems Data transmission equipment operating in the 2 4 GHz ISM band and using wide band modulation techniques Harmonized EN cover
36. o erase everything after you read the warning e Ensure that you have back up all the required data before erasing all data from your device 4 5 Connecting to HDMl compliant Devices via Micro HDMI Input HDMI High Definition Multimedia Interface is a compact audio video interface for transferring uncompressed digital audio video data You can obtain the best user experience for video playback and gaming via HDMI VSD221 is equiped with a micro HDMI input for connection to an external HDMI compliant device You can connect your PC notebook Blu ray player or any other HDMI compliant device to VSD221 for high definition video display Using Your VSD221 Smart Display How to begin 1 A type A HDMI to type D micro HDMI HDMI cable must be available Connect the Type A connector of the HDMI cable to the desired HDMI compliant device Connect the Type D connector of the HDMI cable to the micro HDMI port located on the back of your VSD221 For PC or notebook connection always set the appropriate resolution VSD221 supports with max resolution of 1920 1080 Q P O N To enable the touch screen function connect the micro USB cable to micro USB connector of VSD221 and connect the other end to your PC or notebook e The touch screen function will work with computers running Windows 7 or later versions without the need for additional drivers 4 6 Bluetooth Connection Bluetooth is a short range wireless communi cation
37. of time 4 Removal installation insurance and set up service charges How to get service 1 For information about receiving service under warranty contact ViewSonic Customer Support Please refer to the web site and Customer Support pages You will need to provide your product s serial number 2 To obtain warranty service you will be required to provide a the original dated sales slip b your name c your address d a description of the problem and e the serial number of the product 3 Take or ship the product freight prepaid in the original container to an authorized ViewSonic service center or ViewSonic 4 For additional information or the name of the nearest ViewSonic service center contact ViewSonic Limitation of implied warranties There are no warranties express or implied which extend beyond the description contained herein including the implied warranty of merchantability and fitness for a particular purpose Exclusion of damages ViewSonic s liability is limited to the cost of repair or replacement of the product ViewSonic shall not be liable for 1 Damage to other property caused by any defects in the product damages based upon inconvenience loss of use of the product loss of time loss of profits loss of business opportunity loss of goodwill interference with business relationships or other commercial loss even if advised of the possibility of such damages 2 Any other damages whether inc
38. ogle Permissions This product has an Android platform based on Linux which can be expanded by a variety of JME based application SW All products used in this device and trademarks mentioned herein are trademarks or registered trademarks of their respective owners Google the Google logo Android the Android logo and Gmail are trademarks of Google Inc Use of this trademark is subject to Google Permissions Wi Fi and the Wi Fi CERTIFIED logo are registered trademarks of the Wireless Fidelity Alliance microSD is a trademark of SD Card Association Bluetooth and the Bluetooth logo are trademarks owned by Bluetooth SIG Inc Java JME and all other Java based marks are trademarks or registered trademarks of Sun Microsystems Inc in the United States and other countries S S is a trademark of SRS Labs Inc SRS 3D technology is incorporated under license from SRS Labs Inc SRS 3D restores the original three dimensional sound field of stereo recordings by retrieving spatial information buried in the recordings to create an immersive 3D sound field using only two speakers or headphones The actual included applications apps may differ from the illustrated screen shots VESA is a registered trademark of the Video Electronics Standards Association DPMS and DDC are trademarks of VESA Disclaimer ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein nor for incidenta
39. oted below Examples of exempted components are 1 Mercury in cold cathode fluorescent lamps and external electrode fluorescent lamps CCFL and EEFL for special purposes not exceeding per lamp 1 Short length 500 mm maximum 3 5 mg per lamp 2 Medium length gt 500 mm and 1 500 mm maximum 5 mg per lamp 3 Long length gt 1 500 mm maximum 13 mg per lamp Lead in glass of cathode ray tubes Lead in glass of fluorescent tubes not exceeding 0 2 by weight Lead as an alloying element in aluminium containing up to 0 4 lead by weight Copper alloy containing up to 4 lead by weight Lead in high melting temperature type solders i e lead based alloys containing 85 by weight or more lead 7 Electrical and electronic components containing lead in a glass or ceramic other than dielectric ceramic in capacitors e g piezoelectronic devices or in a glass or ceramic matrix compound O oF W NY Important Safety Instructions o w e Sf a 10 11 12 13 14 15 16 17 18 DO NOT place objects on top of the device as objects may scratch the screen DO NOT expose the device to dirty or dusty environments DO NOT place the device on an uneven or unstable surface DO NOT insert any foreign objects into the device DO NOT expose the device to strong magnetic or electrical field DO NOT expose the device to direct sunlight as it can damage the LCD Screen Keep it away from heat sources
40. p the video button Mld in the right of your friend s name 3 Wait for response Now simply wait for the invited person to join in the video chat Once your request has been accepted by the invited person the display will be switched to the video chat window and the chat will begin Customizing Your VSD221 Smart Display 6 Customizing Your VSD221 Smart Display You can customize your device using the options available in the Settings application 6 1 Display Settings Change the display settings 1 Touch the Home button Apps button Settings Display 2 You can configure the Wallpaper Sleep and Font size here For Wallpaper you can also touch an area on the Home screen to open the Wallpaper configuration screen Enable a setting touch the setting option to select the check box Disable a setting touch the setting option to clear the check box tems Descriptons SSSOS S Wallpaper Refer to 3 6 4 Change the Wallpaper Here you can configure the idling time for entering power saving mode e g 15 sec 30 sec 1 2 5 10 or 30 min by default it is set to 30 minutes Set the Font size to your screen Small Normal Large or Huge by default it is set to Normal 6 2 Sound and Ringtone Settings Change the sound and ringtone settings 1 Touch the Home button Apps button Settings Sound 2 Select the list to locate and touch a desired option 3 To enable a setting touch the setting option
41. processing screen e OSD language supports English Deutsch German Francais French Italian Span ish Japanese Simplified Chinese and Traditional Chinese 6 5 3 OSD Notice Waiting The ViewSonic notice screen will pop up during your OSD configurations No signal The connection for your HDMI is not ready The connection between HDMI device and your smart display is not normalization The No signal information screen will pop up as below Power off or OSD setting for HDMI source OM ers ene Would you like to change to main system Yes No Would you like to shut down or open OSD setting Shut down OSD Cancel Protecting Your VSD221 Smart Display 7 Protecting Your VSD221 Smart Display 7 1 Protect Your Device Data with a Screen Unlock Pattern You can protect your device data against unauthorized access by locking the touch screen with a screen unlock pattern Once the unlock pattern is en abled and the screen is locked you need to draw the correct unlock pattern to unlock the screen After you fail to draw the correct unlock pattern on the screen for five consec utive times you will be asked to wait for 30 seconds before you can try again If you no longer remember your screen unlock pattern follow these steps to unlock your screen 1 Touch Forgot pattern 2 When prompted sign in to the Google website using your Google account name and password 3 Draw a new screen unlock pattern
42. s Google talk Back View No Components Descriptions LAN Connector Connect to a RJ45 cable for network connection DC Jack Connect to power adapter Back Open the compartment cover on the back of the smart Compartment display to connect power adapter LAN cable HDMI cable and insert the SD card 4 SD Card Slot Input micro SD card to extend storage capacity 5 Micro HDMI Connect to digital high quality device for video and audio configurations e g DVD Player BD Player VPG or Notebook VSD221 Smart Display Features 1 1 Installing wall mount bracket The VSD221 supports wall mount bracket installation We recommend using mounting interface that comply with Video Electronics Standards Association VESA standard Please follow the steps to install your bracket Turn off your monitor and unplug its power cord Lay the monitor face down on a flat surface Take care to protect the screen Remove the screws for wall mount and then remove the cover plate a0 N Align the wall mount bracket with the holes which are compliant with VESA standard mounting hole pattern 100mmx100mm in the mounting pad and secure it with the four screws supplied with the arm type base wall mount hanger or other base set Up Your VSD221 Smart Display 2 Set Up Your VSD221 Smart Display 2 1 Connection Sisielslelete s elsls e sieleis slslsteteteleletetetetetetetatetstatatetetstatatstatatet
43. s technology that allows your device to connect to other Bluetooth enabled devices over a wireless network Bluetooth on your device operates in three different modes Status Descriptions O O S Bluetooth is turned on Your device is enabled to detect Bluetooth devices within range but will not be found by them Discoverable Bluetooth is turned on and other Bluetooth devices can detect your device Off Bluetooth is turned off Your device cannot send and receive data using Bluetooth Using Your VSD221 Smart Display 4 6 1 Turn on Bluetooth and make the device discoverable 1 Touch the Home button Apps button Settings Bluetooth Enable the Bluetooth function by touching ON to turn on Bluetooth The Bluetooth icon appears in the status area of the system bar 4 6 2 Pair with a Bluetooth device 4 Touch the Home button Apps button Settings Bluetooth Ensure Bluetooth has been enabled on the device you want to pair with and the device is in Discoverable state 2 Touch SEARCH FOR DEVICES Your device starts to scan for Bluetooth devices within range and then displays all detected devices below the AVAILABLE DEVICES list 3 Detect more devices touch Scan for devices 4 Initiate a connection with a device touch the name of the device 5 You may be prompted to enter a password to authenticate Enter the same password on both devices or enter the password provided by the device manufacturer Ensure that
44. ss all the features on your device It displays application icons widgets shortcuts and so on Applications Software allows you to perform a specific task Power on your device it is preloaded with a variety of applications already You can also download additional applications from the Google Play Store About Your VSD221 Smart Display Widgets Widgets are applications that you can use directly on the Home screen Example Analog clock Bookmark Picture frame the Google search bar and so on Shortcuts A link that you can create on your Home screen to provide quicker access to applications you have installed 3 3 Home Screen Once you power on your device and unlock your screen the central Home screen will display You can also touch the lt Home button to go to Home screen On the Home screen it allows you to access all the features installed in your device The Home screen is composed of five screen panels You can slide your finger to left or right across the central Home screen to view more widgets shortcuts and other items located on each screen panel You can also add shortcuts widgets or change the desktop wallpaper on each screen panel 13 12 Google 4 e Kl 2 8 314 5 16 7 Items cr ip tic INS Gooale cor Use the Google Search application to search J Search the web faster and easier from Google Located at the bottom of the Home screen it includes Back Home Recent Applications
45. stomizing Your VSD221 Smart Display 6 5 OSD Settings Touch the OSD icon on the left of system bar to pop up OSD configuration screen et Refer to 3 4 Navigation buttons The OSD 4 configuration screen can be used to adjust Brightness the volume brightness contrast and so on Contrast Q SRS C amp Main Default S 6 5 1 Adjustment Bars Volume Touch and drag the slider on the Volume bar to adjust the volume Drag the slider to the right the volume is louder By default the volume is set to 70 Brightness Touch and drag the slider on the Brightness bar to adjust the brightness of your screen Drag the slider to the right the screen is brighter By default the brightness is set to 75 Contrast Touch and drag the slider on the Contrast bar to adjust the contrast of screen display Drag the slider to the right the contrast is larger By default the contrast is set to 75 6 5 2 Functions Buttons SRS SRS Sound Retrieval System touch this A D rs on button to enable SRS function e Main or HDMI When input source is internal HDMI SRS Android this item will show you HDMI When input source is external HDMI this item will show you Main Customizing Your VSD221 Smart Display Default Touch Default button to restore the Volume Brightness and Contrast to default value Back Touch Back button to close the OSD configuration screen and go back to the Original
46. stst msns izizizizizizizzisizizisi ists DI aS ISITI III seeeeeces ERII PPPRRRARRARARRR DOSS asle ole oloo O0000 SAAANA BRIS of FS 21 AVA E eA a PESEESSESSSSSSES SSeS ess p Earphone tcs P eem a Notebook SD Card Mouse USB Storage Outliet rn QF Wi Fi Devices 2 2 Get Your Smart Display Ready for Use Insert the SD card Open the compartment cover on the back of the smart display set Up Your VSD221 Smart Display Insert a micro SD card if desired and or available Connect the Power Cord 1 Open the compartment cover on the back of the smart display Connect the included power cord to the power jack 2 i 3 Connect the other end of the power cord to a suitable power outlet set Up Your VSD221 Smart Display 2 3 Turn On Your Device _ _ LED Power Press and hold power button about 1 2 seconds 5 wd 9530 l 9 58 Sat August 4 Sat August 4 Slide the lock icon to unlock the screen 4 After connecting the power cord you can press and hold the power button about 1 2 seconds on the lower right corner to power on your device Once powered up the LED indicator will show solid Green The lock screen will appear after a short boot up period 4 Touch and slide the lock icon to unlock the screen 5 The device is ready for use when the Home screen is displayed 2 4 Turn Off Your Device Would you like to shut down 4 Press and hol
47. t Temperature 20 C 60 C Relative Humidity 20 95 Air pressure 86 106 Kpa Radiation Solar heat 1 12 kWh m IEC68 2 5 72hrs Accessories Power cord 1M Power adapter Micro HDMI to HDMI cable Optional Micro USB to USB cable Optional Customer Support For technical support or product service see the table below or contact your reseller NOTE You will need the product serial number T Telephone F FAX Email Country Region Website Australia New Zealand www viewsonic com au aos eee service au viewsonic com l l l NZ 0800 008 822 l l T Toll Free 1 866 463 4775 Canada www viewsonic com T Toll 1 424 233 2533 service ca viewsonic com F 1 909 468 3757 Europe www viewsoniceurope com www viewsoniceurope com uk support call desk Hong Kong www hk viewsonic com T 852 3102 2900 service hk viewsonic com India www in viewsonic com T 1800 266 0101 service in viewsonic com Korea www kr viewsonic com T 080 333 2131 service kr viewsonic com Latin America l www viewsonic com la T 0800 4441185 soporte viewsonic com Argentina Latin America Chile www viewsonic com la T 1230 020 7975 soporte viewsonic com Latin America l l www viewsonic com la T 01800 9 157235 soporte viewsonic com Columbia Latin America Mexico www viewsonic com la T 001 8882328722 soporte viewsonic com Renta y Datos 29 SUR 721 COL LA PAZ 72160 PUEBLA PUE Tel 01 222 891 55
48. ta that you want the device to synchronize automatically such as Sync Calendar sync Contacts Sync Gmail Sync Picasa Web Albums Import Export You can import contacts from SD card to your device export Contacts from your device to your SD card and share visible contacts in multiple ways such as Bluetooth or Gmail 4 2 Pop up Menu Touch the Menu button on the device or the Menu button on the screen to open or close the pop up menu that lists available options for the current ap plication or actions that you can perform on the current screen Select an option or item on the pop up menu Touch the Menu button on the device or the Menu button on the screen to open the pop up menu 2 Touch the desired item on the pop up menu Using Your VSD221 Smart Display 4 3 Google Search You can use the Google Search widget to find websites and information on Google applica tions installed on your device and contacts stored in your Contacts list Search by typing 1 From the Google Search widget on the Home screen touch Google to open the Google Search widget below 2 Type a keyword or text into the box using the keyboard As you type the search results that fully or partially match the text being typed appear 3 Scroll the listed search results and touch the desired result 4 The matching application or the browser with matching web links opens 5 Touch the desired link if you want to view a web page Se
49. teacentecreenmnineaneaceenercunveetenauucceverstns 11 3 6 Customizing Your Home Screen cccccceecceeeeeeeeeeeeees 12 3 6 1 Add an ltem Shortcut cc ccececeeeeeeeeeeeees 12 3 6 2 Move an ltem ccc cccecceeceeceeeeeeeeeeteeteeseeseeeeeeenes 12 3 6 3 Delete an ltem 0 ccceeceeeeeeeeeeeeeseeteeseeeeenenes 12 3 6 4 Change the Wallpaper s nonnenonnennnnennnnennnrsnnnnsn 12 3 7 Navigating the Applications cccccsscceeceeceeeseeseeeaes 13 3 7 1 ADDS SCIEN ccceccecceceeteeceeeeeceeeeeeeseeseeeeeeeeeenes 13 3 7 2 Application Shortcuts cccceccceeceeeeeeeeeeeeeeenees 14 3 7 3 Recent Applications cccccecseceeceeeeeseeeeeeeeeeees 14 3 7 4 Screen Lock Wallpaper ccccececcsecseeeeeeeeeees 15 4 Using Your VSD221 Smart Display 4 1 Managing Contacts ccccccccceccceeeeeeceeeeeeeeeeeeeeseeeseeeas 16 4 1 1 Add a new contact wis crssussnananonsanandeidesivandenennsaneas 16 4 1 2 Find a contact 0 cee ceeeeeeeeeeeeeeeteeeeeaeeaeeeenees 17 4 1 3 E mail or send a message to a contact 17 4 2 Pop up M nU o onesessenenenensnsnsnrnrererersrsrrrrrrnrnrererernrerrerern 19 4 3 Google Search n nnnnannanonnnnnnnnnnonnnnnnnnrrrnnnnnnnnnrrnnrnennnnni 20 Table of Contents 4 4 Managing Your Device Settings cccceccceceeeeeeeeeeeees 21 4 4 1 Check storage SPACES ceccecccecceeeceeeeeeeeeeeees 21 4 4 2 Remov
50. to select the checkbox to disable a setting touch the setting option to clear the check box Customizing Your VSD221 Smart Display 6 2 1 System settings Items Descriptions Touch Sounds select this item check box to enable the touch sounds By default it is set to enable Screen lock sound Plays a tone when the screen is locked and unlocked By default it is set to enable 6 2 2 Notifications settings Items Descriptions o Notification 1 Select a desired ringtone for notifications from the ringtone Ringtones menu that appears 2 Touch OK to confirm the selection 6 3 Date Time and Time Zone Manually set the date time and time zone Touch the Home button Apps button Settings Date amp time The related configuration about Date amp time will appear on the right section 2 3 Touch the desired item 4 If you want to automatic date amp time please select the Automatic date amp time check box When this check box is not selected you can set the date amp time by manually Items Descriptions Automatic date amp Use network provide time zone automatically time Set date 1 Touch Set date item to adjust the day month and year you can also touch the day month or year to flick to the desired value 2 Touch Done to confirm the date Customizing Your VSD221 Smart Display Items Descriptions S 1 Touch Set time item to adjust the hour and minute you can also touch the
51. touch APPS or WIDGETS tab to enter APPS or WIDGETS configuration screen e Select one of APPS or WIDGETS item that you want to add e Touch and hold the item to add it onto the selected Home screen e Touch and hold a newly added item on the selected Home screen without lifting your finger to drag it to any place you want on the Home screen 3 6 2 Move an Item e On the Home screen touch and hold the item that you want to move e The screen will soon display the shape of the item to indicate that it can be repositioned e Move the item to the specified position e Then release your finger to add the item to the new position 3 6 3 Delete an Item e On the Home screen touch and hold the item that you want to delete such as a widget or shortcut e An X will soon be displayed at the top of the Home screen e Drag the item over the X e Then release your finger to delete the item 3 6 4 Change the Wallpaper e Long Touch touch and hold an empty Choose wallpaper from space on the screen e A Choose wallpaper from configuration tte eit screen will appear e Select one of the wallpaper sources by touching the specified icon Wallpaper sources Gallery Live Wallpapers and Wallpapers e Tap on the desired wallpaper image You can always exit by tapping gt E 3 2 About Your VSD221 Smart Display e Once finishing the wallpaper selection touch Set wallpaper to renew the wallpaper of Home scree
52. upports power saving mode sleeping mode The device will enter power saving mode when you idle without processing Then the screen will go off You can set the duration of screen to remain on before entering sleeping mode touch the Home button Apps button Settings Display Sleep 7 6 Power Management Information Please turn of the product when it will not be used for long time This could potentially increase the life and decrease the power consumption of the product Power Indicator TED Stats Power Standby Power OFF LED OFF Power On In off mode push the power button 1 2 seconds to enter power on mode Power Standby In power on mode push the power button to enter standby mode Power Off In power on mode push the power button more than 4 seconds and select OK in the dialog box to enter off mode Troubleshooting 8 Troubleshooting 8 1 Touch Screen Problems Problems Causes Solutions _ Dust particles or any foreign material on the camera s or reflector s surface may affect image quality and the display s Touch screen does not respond to hand gestures or render them properly touch function 8 2 Messaging Problems 1 Remove any dust or particles from the reflector and camera using compressed air 2 Gently clean the cameras and reflector surface carefully with a soft antistatic brush to avoid scratches 3 Clean any remaining dust with a clean dry dust free
53. utton on the system bar If the desired application shortcut displays on the Home screen touch the shortcut to launch the application 3 3 Recent Applications Open a recently used application Touch the Recent Applications button __ to view the recently used applications scroll the list of recently used applications and touch the desired application thumbnail to launch the application Tap the Back button to close the Recent Applications list 4 Slide your finger horizontally across any one of the applications to remove it from the Recent Applications list About Your VSD221 Smart Display 3 7 4 Screen Lock Wallpaper You can set the display to turn off automatically after a timeout period of inactivity or turn it off manually by pressing the power button When you press the power button to wake up the display the screen lock wallpaper appears to avoid unintentional touch of the screen When the screen lock wallpaper appears touch and hold the lock icon drag it to the edge of the larger circle that surrounds it to unlock the screen Refer to 2 3 Turn On Your Device e Set the duration of screen to remain on before entering sleeping mode touch the Home button Apps button Settings Display Sleep Using Your VSD221 Smart Display 4 Using Your VSD221 Smart Display 4 1 Managing Contacts Touch Home button Apps button People to view and manage your contacts 4 1 1 Add a new contact
Download Pdf Manuals
Related Search