Siig SC-SA0R11-S1
Contents
1. selected physical disk on this vd press Y to select Yes The mirror will begin rebuilding Donotinterfere with the process until completion 11 7 Press F10 to exit the BIOS When asked Do you want to exit from Marvell BIOS setup press Y to exit and reboot Deleting RAID Arrays Deleting a RAID array will destroy data on the hard drives Please backup all data on your hard drive before deleting any RAID array 1 2 As the BIOS boots press Ctrl M when prompted to enter the RAID BIOS Select New_VD press Enter Select Delete then press Enter When asked Do you want to delete this virtual disk press Y to select Yes When asked Do you want to delete MBR from this virtual disk press Y to select Yes Press F10 to exit the BIOS When asked Do you want to exit from Marvell BIOS setup press Y to exit and reboot Driver Installation This section provides information on how to install the drivers Windows 8 32 64 bit Windows 7 32 64 bit Server 2008 R2 For New Installation J Setup the RAID array prior to Windows installation If RAID is not required go directly to step 2 Follow Windows installation procedure At the Windows desktop For Windows 8 7 Right click Computer click Manage click Device Manager Eor Server 2008 R2 Click Computer click Manage Double click Diagnostics click Device Manager Right click Marvell Console or Marvell Console ATA Device under Other devices c2. Device Connection The DP SATA 6Gb s 4 Port Hybrid PCIe supports up to four Serial ATA hard disk drives You will need to purchase additional SATA data cable s if a third or forth channel is going to be used 1 2 Install your hard disk drive s in the chassis Connect the Serial ATA hard disk drive to the system power supply Note For hard drives with both SATA power connector and legacy 4 pin connector use either the SATA power connector or the legacy 4 pin power connector Using both power connectors may damage the hard drive 3 Connect one end of the Serial ATA cable to the hard disk drive Serial ATA Power Figure 2 SATA hard disk drive connections 4 Attach the other end of the Serial ATA data cable to the Serial ATA connector on the DP SATA 6Gb s 4 Port Hybrid PCle 5 Follow the same instructions to connect the second hard drive if needed Device connection is now complete RAID Arrays This controller can be configure for hardware RAID 0 1 and 10 if needed If you don t need RAID 0 1 or 10 please proceed to Driver Installation on page 13 RAID Arrays are setup in the DP SATA 6Gb s 4 Port Hybrid PCIe BIOS 7 RAID 0 Striping This RAID array to be used on New Blank hard drives Striping will destroy data on the hard drive A minimum of 2 drives are needed to configure this array T 2 As the BIOS boots press Ctrl M when prompted to enter the RAID BIOS At the next
3. Follow Windows installation procedure After booting up the Windows click Cancel at the Found New Hardware window For Windows Vista Right click Computer click Manage click Continue click Device Manager For Server 2008 Right click Computer click Manage Double click Diagnostics click Device Manager 9 Right click Marvell Console ATA Device under Other devices click Update Driver Software Click Browse my computer for driver software Insert the driver CD Close the CD autoplay window if prompted For 32 bit Type D Drivers storport i386 click Next Change D to match your CD DVD ROM drive letter For 64 bit Type D Drivers storport amd64 click Next Change D to match your CD DVD ROM drive letter Click Close then restart the computer For Existing Installation iL Setup the RAID array prior to driver installation and boot up to Windows If RAID is not required simply boot up Windows and go directly to step 2 At the Found New Hardware window click Cancel For Windows Vista Click Computer click Manage click Continue click Device Manager For Server 2008 Click Computer click Manage Double click Diagnostics click Device Manager Right click Marvell Console ATA Device under Other devices click Update Driver Software Insert the driver CD Close the CD autoplay window if prompted Click Browse my computer for driver software For 32 bit Type D Drivers storport i386 c
4. click Diagnostics click Device Manager Double click System devices Marvell Unify Configuration should be displayed Marvell Storage Utility Follow the instuctions below to install the Marvell Storage Utility GUI T 2 20 Double click MSUSetup in the GUI folder on your software CD At the User Account Control click Yes or Continue Skip this step if not prompted At Welcome to the Marvell MSU V4 Setup Wizard click Next At License Agreement select I accept the terms of the License Agreement click Next Click Next again Change the Destination folder if you want to change it otherwise click Install Click Allow access at the Windows Security Alert Skip this step if not prompted At the Completing the Marvell MSU V4 Setup Wizard click Finish After successful installation the MSU GUI is ready for use Enable the software by double click on it 10 11 Type in the Username and Password to log in Username and Password are your Windows user name and password If you have a user name but no password please leave the password field blank Usememe Domain UserName password O Remember password twin Figure 3 After log in you can access to the MSU user interface for further VD management See Figure 4 in the next page Refer to your UserGuide on the software CD for more details 21 22 Proper Technical Supportand Warranty QUESTIONS SI
5. each connectors SATA 1 2 and eSATA 5 6 are interchangeable Follow the instructions in Table 1 to configure the jumper Output co SATA 1 SATA 2 SATA 3 SATA 4 JP1 JP8 1 2 short SATA 3 SATA 4 eSATA 5 eSATA 6 JP1 JP8 2 3 short SATA 2 SATA3 JP1 JP4 1 2 short SATA 4 eSATA 5 JP5 JP8 2 3 short SATA 1 SATA3 JP1 JP4 2 3 short SATA 4 eSATA 6 JP5 JP8 1 2 short Table 1 Jumper Settings Hardware Installation For Low profile systems install the spare low profile bracket now General instructions for installing the card are provided below Since the design of computer cases and motherboards vary refer to your computer s reference manual for further information if needed Static Electricity Discharge may permanently damage your system Discharge any static electricity build up in your body by touching your computer case for a few seconds Avoid any contact with internal parts and handle cards only by their external edges 1 Turn OFF the power to your computer and any other connected peripheral devices 2 Unplug the power cord from the back of the computer 3 Remove your computer cover 4 Remove the slot bracket cover from an available PCI Express slot Carefully align the card s bus connector with the selected PCI Express slot on the motherboard Push the board down firmly but gently until it is well seated Replace the slot bracket holding screw to secure the card
6. DP SATA 6Gb s 4 Port Hybrid PCle Quick Installation Guide Q Introduction The DP SATA 6Gb s 4 Port Hybrid PCIe is a high performance SATA host adapter designed to add four internal Serial ATA 6Gb s channels and two eSATA external connectors to your PCle equipped computer Features and Benefits e Compliant with Serial ATA specification Revision 3 0 e Hybrid HyperDuo enables 80 of SSD performance at one third the cost e Hardware RAID to offload the host CPU for maximum performance e Supports RAID 0 1 amp 10 e Supports Port Multiplier FIS based and Native Command Queuing NCQ e Supports TRIM to extend the life of SSDs for maximum durability 04 0860A 1 System Requirements e Desktop PC with an available 4 lane or more PCIe slot e Windows 8 32 64 bit 7 32 64 bit Vista 32 64 bit XP 32 64 bit Server 2003 amp 2008 32 64 bit Server 2008 R2 Package Contents DP SATA 6Gb s 4 Port Hybrid PCIe e Spare low profile bracket e SATA data cable 2 Driver CD e Quick installation guide Layout 3 21 2 eSATA connectors HDD LED optional hd a Pf SATA 3 bottom 2 amp SATA 4 top ee SATA 1 ps 0 bottom re oO amp SATA 2 4SATA yp7 Le top internal JP8 connectors Figure 1 Layout Note The internal SATA 3 and SATA 4 connectors are dedicated channels they can not be disabled Jumper Settings Refer to Figure 1 for the positions of
7. IG s Online Support has answers Simply visit our web site at www siig com and click Support Our online support database is updated daily with new drivers and solutions Answers to your questions could be just a few clicks away You can also submit questions online and a technical support analyst will promptly respond SHG offers a 5 year manufacturer warranty with this product This warranty covers the original purchaser and guarantees the product to be free of any defects in materials or workmanship for five 5 years from the date of purchase of the product SUG will at our discretion repair or replace with an identical product or product having similar features and functionality the product if defective in materials or workmanship This warranty gives you specific legal rights and you may also have other rights which vary from state to state Please see our web site for more warranty details If you encounter any problems with this product please follow the procedures below A If it is within the store s return policy period please return the product to the store where you purchased from B If your purchase has passed the store s return policy period please follow the steps below to have the product repaired or replaced Step 1 Submit your RMA request Go to www siig com click Support then REQUEST A PRODUCT REPLACEMENT to submit a request to SIG RMA or fax a request to 510 657 5962 Your RMA request will be processed if t
8. he product is determined to be defective an RMA number will be issued Step 2 After obtaining an RMA number ship the product e Properly pack the product for shipping All accessories that came with the original package must be included e Clearly write your RMA number on the top of the returned package SIIG will refuse to accept any shipping package and will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton e You are responsible for the cost of shipping to SIIG Ship the product to the following address SIIG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA RMA e SIG will ship the repaired or replaced product via Ground in the U S and International Economy outside of the U S at no cost to the customer 23 About SIIG Inc Founded in 1985 SIG Inc is a leading manufacturer of IT connectivity solutions including Serial ATA and Ultra ATA Controllers FireWire USB and legacy I O adapters that bridge the connection between Desktop Notebook systems and external peripherals SIIG continues to grow by adding A V and Digital Signage connectivity solutions to our extensive portfolio SIG products offer comprehensive user manuals many user friendly features and are backed by an extensive manufacturer warranty High quality control standards are evident by the overall ease of installation and compatibility of our products as wellas one of the lowest defect
9. ive return rates in the industry SIG products can be found in computer retail stores mail order catalogs through major distributors system integrators and VARs in the Americas and the UK and through e commerce sites PRODUCT NAME DP SATA 6Gb s 4 Port Hybrid PCIe FCC RULES TESTED TO COMPLY WITH FCC PART 15 CLASS B OPERATING ENVIRONMENT FOR HOME OR OFFICE USE FCC COMPLIANCESTATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE SHG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA Phone 510 657 8688 DP SATA 6Gb s 4 Port Hybrid PCle is a trademark of SIIG Inc SIIG and the SIIG logo are registered trademarks of SIIG Inc Microsoft and Windows are registered trademarks of Microsoft Corporation All other names used in this publication are for identification only and may be trademarks of their respective owners February 2013 Copyright 2013 by SIG Inc All rights reserved
10. lick Next Change D to match your CD DVD ROM drive letter For 64 bit Type D Drivers storport amd64 click Next Change D to match your CD DVD ROM drive letter Click Close then restart the computer Windows XP 32 64 bit Server 2003 32 64 bit Important New Installation is not supported by Windows XP and Windows Server 2003 For Existing Installation 1 Setup the RAID array prior to driver installation and boot up Windows If RAID is not required simply boot up Windows and go directly to step 2 2 At the Found New Hardware window click No not this time click Next Skip this step if not prompted 3 Click Install from a specific location advanced click Next 4 Check Include this location in the search uncheck the other box 5 Insert driver CD For 32 bit Type D Drivers miniport i386 click Next Change D to match your CD DVD ROM drive letter For 64 bit Type D Drivers miniport amd64 click Next Change D to match your CD DVD ROM drive letter 6 fe 8 Click Finish Repeat steps 2 6 Restart the computer To Verify Windows Installation 1 Use Device Manager to verify installation For Windows 8 7 XP Server 2003 Right click Computer or My Computer click Manage click Device Manager For Windows Vista Right click Computer click Manage click Continue Click Device Manager For Windows Server 2008 2008 R2 Right click Computer click Manage Double
11. lick Update Driver Software Click Browse my computer for driver software insert the driver CD Close the CD autoplay window if prompted 7 For 32 bit Type D Drivers storport i386 click Next Change D to match your CD DVD ROM drive letter For 64 bit Type D Drivers storport amd64 click Next Change D to match your CD DVD ROM drive letter Click Close then restart the computer For Existing Installation ile Setup the RAID array prior to driver installation and boot up to Windows If RAID is not required simply boot up Windows and go directly to step 2 For Windows 8 7 Right click Computer click Manage click Device Manager For Server 2008 R2 Click Computer click Manage Double click Diagnostics click Device Manager Right click Marvell Console or Marvell Console ATA Device under Other devices click Update Driver Software Click Browse my computer for driver software insert the driver CD Close the CD autoplay window if prompted 6 For 32 bit Type D Drivers storport i386 click Next Change D to match your CD DVD ROM drive letter For 64 bit Type D Drivers storport amd64 click Next Change D to match your CD DVD ROM drive letter Click Close then restart the computer Windows Vista 32 64 bit Server 2008 32 64 bit For A New Installation I Setup the RAID array prior to Windows installation If RAID is not required go directly to step 2
12. screen select HBA 0 Marvell 0 press Enter Select Configuration Wizard then press Enter Use the Up or Down arrow key to choose a hard drive Press the Spacebar to select the hard drive Perform the same procedure with the other hard drive s you want to add to the array When you are finished selecting the hard drives press Enter Select RAID Level or HyperDuo press Enter Select RAID 0 then press Enter Note You can rename the VD Name This is optional Select Next press Enter When asked Do you want to create this virtual disk press Y to select Yes 6 Press F10 to exit the BIOS When asked Do you want to exit from Marvell BIOS Setup press Y to exit and reboot RAID 1 Mirror Two drives are needed to make a Mirror 1 As the BIOS boots press Ctrl M when prompted to enter the RAID BIOS 2 At the next screen select HBA 0 Marvell 0 press Enter Select Configuration Wizard then press Enter 3 Use Up or Down arrow key to choose a hard drive Press Spacebar to select the hard drive Perform the same procedure with the other hard drive Once both hard drives are selected press Enter 4 Select RAID Level or HyperDuo press Enter Select RAID1 then press Enter Note You can rename the VD Name This is optional 5 Select Next press Enter When asked Do you want to create this virtual disk press Y to select Yes 9 6 Press F10 to exit the BIOS When asked Do you want to exi
13. t from Marvell BIOS Setup press Y to exit and reboot RAID 10 Mirror Striping Four drives are needed to make a RAID10 1 As the BIOS boots press Ctrl M when prompted to enter the RAID BIOS 2 At the next screen select HBA 0 Marvell 0 press Enter Select Configuration Wizard then press Enter 3 Use Up or Down arrow key to choose hard drive Press Spacebar to select the hard drive Perform the same procedure with the other hard drives Once all hard drives are selected press Enter 4 Select RAID Level or HyperDuo press Enter Select RAID10 then press Enter Note You can rename the VD Name This is optional 5 Select Next press Enter When asked Do you want to create this virtual disk press Y to select Yes 6 Press F10 to exit the BIOS When asked Do you want to exit from Marvell BIOS Setup press Y to exit and reboot Rebuilding a Failed Mirror Set When a failure to one member occurs you will be notified by the RAID BIOS during boot up The steps below will guide you in rebuilding a failed mirror set 1 Replace the failed drive with one of equal or greater capacity then boot the computer 2 As the BIOS boots press Ctrl M when prompted to enter the RAID BIOS 3 Select New_VD press Enter Select Rebuild then press Enter 4 Select the new hard drive under Free Physical Disks 5 Press Spacebar to select hard drive then press Enter 6 When asked Do you want to rebuild with
Download Pdf Manuals
Related Search