Kramer Electronics VS-48HDXL video switch
Contents
1. This type of connection is recommended for identification of the factory default IP Address of the VS A48HDXI during the initial configuration After connecting the Ethernet port configure your PC as follows 1 Right click the My Network Places icon on your desktop 2 Select Properties 1 According to SMPTE RP 168 The sources must be genlocked to the GENLOCK input in order to switch cleanly 2 The unit will detect automatically when SD SDI inputs are used 3 If a change is made to the resolution or refresh rate The button will not flash if the new timing is the same as that previously selected 4 After connecting the Ethernet port you have to install and configure your Ethernet Port and also install the COM Port Redirector For detailed instructions see the Ethernet Configuration Lantronix guide pdf file in the technical support section our Web site http www kramerelectronics com 17 Connecting the VS 48HDxl 3G HD SD SDI 4x8 Matrix Switcher 3 Right click Local Area Connection Properties 4 Select Properties The Local Area Connection Properties window appears 5 Select the Internet Protocol TCP IP and click the Properties Button see Figure 7 General Connect using Big Netfinity 10 100 Ethemet Adapter Components checked are used by this connection E Client for Microsoft Networks a File and Printer Sharing for Microsoft Networks ocol TCP IP K KK2. 10 13 14 14 15 16 16 17 17 17 19 19 19 20 20 20 21 21 22 22 22 22 23 23 24 24 25 Contents Figures Figure 1 VS 48HDxl 3G HD SD SDI 4x8 Matrix Switcher 2 Figure 2 Connecting the 5 48 3G HD SD SDI 4x8 Matrix Switcher 11 Figure 3 Connecting the Dual Link VS 48HDxl 3G HD SD SDI 4x8 Matrix Switcher 13 Figure 4 VS 48HDxl SETUP Dipswitches 14 Figure 5 Connecting a PC without using a Null modem Adapter 15 Figure 6 Controlling via RS 485 for example using an RC 3000 16 Figure 7 Local Area Connection Properties Window 18 Figure 8 Internet Protocol TCP IP Properties Window 18 Figure 9 Using the Remote Connector 19 Tables Table 1 Front Panel VS 48HDxl 3G HD SD SDI 4x8 Matrix Switcher 6 Table 2 Rear Panel VS 48HDxl 3G HD SD SDI 4x8 Matrix Switcher 7 Table 3 Machine Dipswitch Settings 14 Table 4 Technical Specifications of the VS A48HDxl 24 Table 5 VS A48HDxl Hex Codes for Switching via RS 232 RS 485 24 Table 6 Protocol Definitions 25 Table 7 Instruction Codes for Protocol 2000 26 ii KRAMER SIMPLE CREATIVE TECHNOLOGY Introduction 2 1 Introduction Welcome to Kramer Electronics Since 1981 Kramer Electronics has been providing a world of unique creative and affordable solutions to the vast range of problems that confront the video audio presentation and broadcasting professional on a daily basis In recent years we have redesigned and upgraded most of our line
3. Install Uninstall Properties Description Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks Show icon in taskbar when connected Figure 7 Local Area Connection Properties Window 6 Select Use the following IP address and fill in the details as shown in Figure 8 7 Click OK aixi General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically 4 Use the following IP address IP address 192 168 1 2 Subnet mask 255 255 0 Default gateway 1 s Obtain DNS 1 address automatically 4 Use the following DNS server addresses 3 Preferred DNS server Alternate DNS server 3 Figure 8 Internet Protocol TCP IP Properties Window 18 KRAMER SIMPLE CREATIVE TECHNOLOGY Connecting the VS 48HDxl 3G HD SD SDI 4x8 Matrix Switcher 6 8 2 Connecting the ETHERNET Port via a Network Hub Straight Through Cable You can connect the Ethernet port of the VS 44HDxl to the Ethernet port on a network hub or network router via a straight through cable with RJ 45 connectors 6 8 3 Configuring the Ethernet Port After connecting the Ethernet port you have to install and configure it For d
4. ii Product modification or failure to follow instructions supplied with the product iii Repair or attempted repair by anyone not authorized by Kramer iv Any shipment of the product claims must be presented to the carrier v Removalor installation of the product vi Any other cause which does not relate to a product defect vii Cartons equipment enclosures cables or accessories used in conjunction with the product WHAT WE WILL PAY FOR AND WHAT WE WILLNOT PAY FOR We will pay labor and material expenses for covered items We will not pay for the following 1 Removal or installations charges 2 Costs of initial technical adjustments set up including adjustment of user controls or programming These costs are the responsibility of the Kramer dealer from whom the product was purchased 3 Shipping charges HOW YOU CAN GET WARRANTY SERVICE 1 To obtain service you product you must take or ship it prepaid to any authorized Kramer service center 2 Whenever warranty service is required the original dated invoice or a copy must be presented as proof of warranty coverage and should be included in any shipment of the product Please also include in any mailing a contact name company address and a description of the problem s 3 For the name of the nearest Kramer authorized service center consult your authorized dealer LIMITATION OF IMPLIED WARRANTIES All implied warranties including warranties of merchantability and f
5. 9 OFF Button An OFF OUT combination disconnects that output from the inputs an OFF ALL combination disconnects all the outputs Press and hold to toggle between the 4x8 switcher mode and the dual link 2x4 switcher mode 10 LOCK Button Disengages engages the front panel buttons 11 7 segment Display Displays the selected input switched to the output marked above each input 1 The 7 segment display shows 12341234 indicating that the operation mode is normal and that the setups stored via the INPUT OUTPUT buttons have been erased 2 For example press STO and then the Output button 3 to store in Setup 3 3 When in Confirm mode the TAKE button illuminates 4 See section 7 2 5 For example press ALL and then Input button 2 to connect input 2 to all the outputs 6 For more than 3 seconds KRAMER SIMPLE CREATIVE TECHNOLOGY Your VS A8HDxl 3G HD SD SDI 4x8 Matrix Switcher Table 2 Rear Panel VS 48HDxl HD SD SDI 4x6 Matrix Switcher L Feature Function 12 GENLOCK BNC Connector Connect to the Genlock source 13 TERM 750 Button Press to terminate the Genlock source 750 or release for looping 14 LOOP BNC Connector Connect to the GENLOCK connector of the next unit in the line 15 DUAL LINK INPUT BNC In the dual link mode connect the source to inputs 1 and 2 and or inputs 3 Connectors and 4 DUAL LINK 1 and or DUAL LINK 2 16 INPUT
6. making the best even better Our 1 000 plus different models now appear in 11 groups that are clearly defined by function Congratulations on purchasing your Kramer VS 48HDxl 3G HD SD SDI 4x6 Matrix Switcher This product is ideal for e Broadcasting and production studios e Presentation applications The package includes the following items e VS A48HDxl 3G HD SD SDI 4x8 Matrix Switcher e Power cord Null modem adapter and infrared remote control transmitter 3 e This user manual Getting Started We recommend that you e Unpack the equipment carefully and save the original box and packaging materials for possible future shipment e Review the contents of this user manual e Use Kramer high performance high resolution cables Quick Start This quick start chart summarizes the basic setup and operation steps 1 GROUP 1 Distribution Amplifiers GROUP 2 Switchers and Matrix Switchers GROUP 3 Control Systems GROUP 4 Format Standards Converters GROUP 5 Range Extenders and Repeaters GROUP 6 Specialty AV Products GROUP 7 Scan Converters and Scalers GROUP 8 Cables and Connectors GROUP 9 Room Connectivity GROUP 10 Accessories and Rack Adapters GROUP 11 Sierra Products 2 We recommend that you use only the power cord supplied with this device 3 Download up to date Kramer user manuals from the Internet at this URL http www kramerelectronics com 4 The complete list of Kramer cables is our Web site
7. 48HDxl in a Rack This section describes how to install the VS A48HDxlI in a rack Before Installing in a rack How to Rack Mount Before installing in a rack be sure that the environment is within the recommended range Operating temperature range 5 to 45 C 41 to 113 F Operating humidity range 10 to 90 RHL non condensing Storage temperature range 20 to 70 4 to 158 F Storage humidity range 5 to 95 RHL non condensing N CAUTION When installing on a 19 rack avoid hazards by taking care that 1 Itis located within the recommended environmental conditions as the operating ambient temperature of a closed or multi unit rack assembly may exceed the room ambient temperature 2 Once rack mounted enough air will still flow around the machine 3 The machine is placed straight in the correct horizontal position 4 You do not overload the circuit s When connecting the machine to the supply circuit overloading the circuits might have a detrimental effect on overcurrent protection and supply wiring Refer to the appropriate nameplate ratings for information For example for fuse replacement see the value printed on the product label 5 The machine is earthed grounded in a reliable way and is connected only to an electricity socket with grounding Pay particular attention to situations where electricity is supplied indirectly when the power cord is
8. 87 88 81 81 81 81 81 81 81 81 IN 3 01 01 01 01 01 01 01 01 83 83 83 83 83 83 83 83 81 82 83 84 85 86 87 88 81 81 81 81 81 81 81 81 4 01 01 01 01 01 01 01 01 84 84 84 84 84 84 84 84 81 82 83 84 85 86 87 88 81 81 81 81 81 81 81 81 1 Specifications are subject to change without notice 2 P N 5 50 24 KRAMER SIMPLE CREATIVE TECHNOLOGY Kramer Protocol 2000 10 Kramer Protocol 2000 The VS 48HDxl is compatible with Kramer s Protocol 2000 version 0 50 below This RS 232 RS 485 communication protocol uses four bytes of information as defined below For RS 232 a null modem connection between the machine and controller is used The default data rate 15 9600 baud with no parity 8 data bits and 1 stop bit Table 6 Protocol Definitions MSB LSB DESTI INSTRUCTION NATION 0 D N5 N3 N2 N1 NO 7 6 5 4 3 2 0 1st byte INPUT 1 l6 15 14 12 1 10 7 6 5 4 3 2 0 2nd byte OUTPUT 1 O6 05 O4 03 02 O1 00 7 6 5 4 3 2 0 3rd byte MACHINE NUMBER 1 OVR X M4 M3 M2 M1 Mo 7 6 5 4 3 2 0 4th byte 1 Bit 7 Defined as 0 D DESTINATION 0 for sending information to the switchers from the PC 1 for sending to the PC from the switcher N5 N0 INSTRUCTION The function that is to be performed by the switcher s is defined by the INSTRUCTION 6 bits Similarly i
9. and then switch on the power on each device 2 When only one output is required connect that output and leave the other output unconnected 3 Not illustrated in Figure 2 4 Pushed in terminates the input Release when the input extends to another unit 5 We recommend that you use only the power cord that is supplied with this machine 12 KRAMER SIMPLE CREATIVE TECHNOLOGY Connecting the VS 48HDxl 3G HD SD SDI 4x8 Matrix Switcher HD SD SDI Camera Preview 3G HD Video Server HD SDI Mixer Figure 3 Connecting the Dual Link VS 48HDxl 3G HD SD SDI 4x8 Matrix Switcher 6 2 Working Mode Setting You can set the VS 48HDxI to work in the dual link mode as follows To switch to the dual link mode press and hold the OFF front panel button for 3 seconds until a red dot illuminates on the display on the fourth segment of the 7 segment display and the OFF button blinks e To exit the dual link mode press and hold the OFF front panel button for 3 seconds until the red dot on the display disappears and the OFF button blinks Connecting the VS 48HDxl 3G HD SD SDI 4x8 Matrix Switcher 6 3 Dipswitch Settings By default all dipswitches are set to OFF Figure 4 illustrates the VS A8HDxl dipswitches SETUP Figure 4 VS 48HDxl SETUP Dipswitches 6 3 1 Setting the Setup Dipswitches The setup dipswitches determine the address of each VS 48HDxl unit when several VS 48HDxl units are connected to a PC or serial co
10. at http www kramerelectronics com 1 Getting Started Step 1 Mount the machine Mount the machine in a rack or stick the 4 rubber 9 feet to the underside Connect a GENLOCK source Aus In the dual link mode x ODs IN connect the dual link Connect the NN cured to DUAL LINK LOOP connector NPUT 1 and 2 A SET THE DIPSWITCHES gt dipewitches are HD SD SDI Camera Preview 3G HD Video Server HD SDI Mixer Step 3 Turn the power ON Step 4 Operate the machine see section 7 Use the SELECTOR buttons to Connect a selected input switch the inputs to the outputs to ALL the outpute disconnect an output OFF from an input Press TAKE to Press and hold OFF for 3 confirm actions seconds to enter or exit the dual link mode Store STO and recall RCL the status LOCK the front panel Operate via the front panel buttons K5 252 RS 485 remote connectors and the Ethernet KRAMER SIMPLE CREATIVE TECHNOLOGY Overview 3 Overview The Kramer VS 48HDxl can be used as a high performance 4x8 matrix switcher or as a dual link 2x4 switcher which lets you simultaneously route any of the inputs to any or all of the outputs for all SDI video signals using BNC connectors In particular the VS 48HDx
11. not plugged directly into the socket in the wall for example when using an extension cable or a power strip and that you use only the power cord that is supplied with the machine To rack mount a machine 1 Attach both ear brackets to the machine To do so remove the screws from each side of the machine 3 on each side and replace those screws through the ear brackets 2 Place the ears of the machine against the rack rails and insert the proper screws not provided through each of the four holes in the rack ears Note that n some models the front panel may feature built in rack ears Detachable rack ears can be removed for desktop use e Always mount the machine in the rack before you attach any cables or connect the machine to the power e If you using a Kramer rack adapter kit for a machine that is not 19 see the Rack Adapters user manual for installation instructions you can download it at http www kramerelectronics com Connecting the VS 48HDxl 3G HD SD SDI 4x8 Matrix Switcher 6 Connecting the VS 48HDxl 3G HD SD SDI 4x8 Matrix Switcher To connect VS 48HDxl 3G HD SD SDI 4x8 Matrix Switcher as illustrated in the example in Figure 2 do the following l Connect up to four SDI sources to the SDI INPUT BNC connectors for example an HD SD SDI camera to input 1 and a 3G HD video server to input 4 Connect the SDI OUTPUT BNC connectors to up to eig
12. to PIN 3 9 pin D sub 9 pin D sub From PC Male PIN 4 is connected to PIN 6 PINs 8 7 1 are connected together If a shielded cable is used connect the shield to PIN 5 Figure 5 Connecting a PC without using a Null modem Adapter 15 Connecting the VS 48HDxl 3G HD SD SDI 4x8 Matrix Switcher 6 5 Controlling via the RS 485 Port To cascade up to eight individual VS 48HDxl units via RS 485 with control via a Master Programmable Remote Control system such as the Kramer RC 3000 as Figure 6 illustrates do the following 1 Connect the PINS on the RS 485 terminal block port of the RC 3000 to the and PINS respectively on each of the eight VS A48HDXxl units If using shielded twisted pair cable the shield is usually connected to the Ground PIN of the first unit 2 Set the first VS 48HDxl unit as MACHINE 1 and the following seven VS 48HDxl units as MACHINE 2 to MACHINE 8 according to Table 3 RC 3000 MACHINE 1 oe MES mem mim pex Pm E E 2 o O OOO O OO O O O O O O OQ FE MACHINE 8 cures SETUP Figure 6 Controlling via RS 485 for example using an RC 3000 6 6 Factory Reset Press and hold the input buttons 1 2 and 3
13. BNC Connectors Connect to the serial digital video sources from 1 to 4 17 DUAL LINK OUTPUT BNC in the dual link mode connect the acceptors to outputs 1 and 2 and or Connectors outputs 3 and 4 and or outputs 5 and 6 and or outputs 7 and 8 DUAL LINK 1 and or DUAL LINK 2 and or DUAL LINK 3 and or DUAL LINK 4 respectively 18 OUTPUT BNC Connectors Connect to the serial digital video acceptors from 1 to 8 19 RS 232 9 pin D sub Port Connects to the PC or the Remote Controller 20 RESET Button Press to reset Ethernet to factory default definitions IP number 192 168 1 39 Mask 255 255 255 0 Gateway 192 168 1 1 21 ETHERNET RJ 45 Connector Connects to the PC or other Serial Controller through computer networking 22 REMOTE INPUT Terminal Connect to dry contact switches from 1 to 4 Block Connectors 23 REMOTE OUTPUT Connect to dry contact switches from 1 to 8 Terminal Block Connectors 24 5 485 Detachable Pin is for the Ground connection pins B and are for RS 485 Terminal Block Port 25 REMOTE IR Opening Connects to an external IR receiver unit for controlling the machine via an IR remote controller instead of using the front panel IR receiver 26 SETUP Dipswitches Dipswitches for setup of the unit 27 Power Connector with Fuse AC connector enabling power supply to the unit Push in to terminate the input Release when the input extends to another unit 2 First disconnect the po
14. Dual Link Mode You can use your VS 48HDXl in the dual link mode to switch any of the two dual link SDI inputs to any or all of the four dual link SDI outputs as the illustration in Figure 3 shows To connect the VS 48HDxl 3G HD SD SDI 4x4 Matrix Switcher in the dual link mode do the following 1 Connect one or both of the SDI sources to the INPUT DUAL LINK BNC connectors For example a dual link HD SD SDI camera to DUAL LINK 1 inputs and 2 and a dual link 3G HD video server to DUAL LINK 2 inputs 3 and 4 Connect the SDI OUTPUT BNC connectors to up to four SDI acceptors For example OUTPUT DUAL LINK 1 outputs 1 and 2 to a dual link preview display and OUTPUT DUAL LINK 4 outputs 7 and 8 to a dual link HD SDI mixer Set the dipswitches see section 6 3 If required connect A Genlock source to the GENLOCK BNC connector LOOP BNC connector to the GENLOCK connector of the next unit in the line and release the TERM button for looping Connect a PC and or controller if required to the RS 222 port see section 6 4 and or RS 485 port see section 6 5 and or ETHERNET connector see section 6 6 If required connect a remote dry contact switch refer to section 6 9 Connect the power cord Set the machine to the dual link mode see section 6 2 1 Switch OFF the power on each device before connecting it to your 5 48 After connecting your VS 48HDxl switch on its power
15. E 8 The reply is as in TYPE 3 above except that here the OUTPUT is assigned with the value O if the setup is not defined no valid input is detected or 1 if it is defined valid input is detected NOTE 13 This is a request to identify the switcher s in the system If the OUTPUT is set as 0 and the INPUT is set as 1 2 5 or 7 the machine will send its name The reply is the decimal value of the INPUT and OUTPUT For example for a 2216 the reply to the request to send the audio machine name would be HEX codes 7D 96 90 81 i e 128dec 22dec for 2nd byte and 128dec 16dec for 3rd byte 26 KRAMER SIMPLE CREATIVE TECHNOLOGY Kramer Protocol 2000 If the request for identification is sent with the INPUT set as 3 or 4 the appropriate machine will send its software version number Again the reply would be the decimal value of the INPUT and OUTPUT the INPUT representing the number in front of the decimal point and the OUTPUT representing the number after it For example for version 3 5 the reply to the request to send the version number would be HEX codes 7D 83 85 81 i e 1284 3dec for 2nd byte 128dec 5dec for 3rd byte If the OUTPUT is set as 1 then the ASCII coding of the lettering following the machine s name is sent For example for the VS 7588YC the reply to the request to send the first suffix would be HEX codes 7D D9 C3 81 i e 128dec ASCII for Y 128dec ASCII for NOTE 14 The
16. Kramer Electronics Ltd USER MANUAL Model VS A8HDxI 3G HD SD SDI 4x8 Matrix Switcher Contents Contents 1 Introduction 2 Getting Started 2 1 Quick Start 3 Overview 4 Your VS 48HDxl 3G HD SD SDI 4x8 Matrix Switcher 4 1 Using the IR Transmitter 5 Installing the VS 48HDx a Rack 6 Connecting the VS 48HDxl 3G HD SD SDI 4x8 Matrix Switcher 6 1 Connecting the VS 48HDxl in the Dual Link Mode 6 2 Working Mode Setting 6 3 Dipswitch Settings 6 3 1 Setting the Setup Dipswitches 6 4 Controlling via RS 232 for example using a PC 6 5 Controlling via the RS 485 Port 6 6 Factory Reset 6 7 Switching Genlocked Video Signals 6 8 Controlling via ETHERNET 6 8 1 Connecting the ETHERNET Port directly to a PC Crossover Cable 6 8 2 Connecting the ETHERNET Port via a Network Hub Straight Through Cable 6 8 3 Configuring the Ethernet Port 6 9 Controlling via the REMOTE Connector 7 Operating the VS 48HDxl 74 Switching OUT IN Combinations 7 1 Switch OUT IN Combinations 7 1 2 Switch OUT IN Combinations in the Dual Link Mode 7 2 Confirming Settings 7 2 Toggling between the AT ONCE and CONFIRM Modes 7 2 2 Confirming a Switching Action 7 3 Storing Recalling Input Output Configurations 7 3 1 Storing an Input Output Configuration 7 3 2 Recalling an Input Output Configuration 7 4 Locking the Front Panel 8 Technical Specifications 9 Table of Hex Codes for Serial Communication 10 Kramer Protocol 2000 5 nk We
17. SC or PAL compatible video format consisting of 480 for NTSC or 576 for PAL lines of interlaced video 2 High Definition HD means a video format consisting of 720 active lines of progressive video or 1080 lines of progressive or interlaced video 3 The sources must be genlocked to the GENLOCK input in order to switch cleanly Your VS A8HDxl 3G HD SD SDI 4x8 Matrix Switcher To achieve the best performance e Connect only good quality connection cables thus avoiding interference deterioration in signal quality due to poor matching and elevated noise levels often associated with low quality cables e Avoid interference from neighboring electrical appliances that may adversely influence signal quality and position your Kramer VS 48HDxI from moisture excessive sunlight and dust Your VS 48HDxl HD SD SDI 4x8 Matrix Switcher Figure 1 Table 1 and Table 2 define the VS 48HDxl 3G HD SD SDI 4x8 Matrix Switcher KRAMER SIMPLE CREATIVE TECHNOLOGY Your VS A8HDxI 3G HD SD SDI 4x8 Matrix Switcher 2 OUTPUT 3 4 5 6 7 8 L LJ 2 INPUT 3 4 sro 4x8 Matrix Switcher 4 P 2 DUA uas A rm d ENSE R MENS w SZ DSF AY 4 1 2 2 7 3 4 5 6 T B ww L INPUTS SL OUTPUTS ll RS 485 SETUP Figure 1 VS 48HDxl 3G HD SD SDI 4x8 Matrix Switcher Your VS A8HDxl 3G HD SD SDI 4x8 Matrix Switcher Table 1 Front Panel VS 4S8HDxl 3G HD
18. SD SDI 4x8 Matrix Switcher Feature Function 1 IR Receiver The red LED is illuminated when receiving signals from the Infrared remote control transmitter 2 POWER Switch Illuminated switch for turning the unit ON or OFF 3 OUTPUT DUAL LINK Select the output to which the input is switched from 1 to 8 Selector Buttons In the dual link mode select the output DUAL LINK 1 to DUAL LINK 4 to which the input is switched 4 INPUT DUAL LINK Select the input to switch to the output from 1 to 4 Selector Buttons In the dual link mode select input DUAL LINK 1 or DUAL LINK 2 to Switch to the outputs Press IN buttons 1 2 and 3 simultaneously to reset the machine to its factory default values see section 6 6 Use to set the resolution when switching genlocked video signals see section 6 7 5 STO STORE Button Pressing STO followed by an INPUT OUTPUT button stores the current setting 6 TAKE Button Pressing TAKE toggles the mode between the CONFIRM mode and the AT ONCE mode user confirmation per action is unnecessary When in CONFIRM mode the TAKE button implements a pending operation 7 ALL Button Pressing ALL followed by an NPUT button connects that input to all outputs 8 RCL RECALL Button Pressing the RCL button and the corresponding INPUT OUTPUT key displays a setup from the non volatile memory After pressing the same memory location the second time the settings will take effect
19. an authorized Kramer technician Any user who makes changes or modifications to the unit without the expressed approval of the manufacturer will void user authority to operate the equipment BO Usethesupplied DC power supply to feed power to the machine BO Please use recommended interconnection cables to connect the machine to other components and CE approved using STP cable for twisted pair products 28 KRAMER SIMPLE CREATIVE TECHNOLOGY For the latest information on our products and a list of Kramer distributors visit our Web site www kramerelectronics com where updates to this user manual may be found We welcome your questions comments and feedback Caution Safety Warning Disconnect the unit from the power supply before opening servicing Institute of Quality amp Control Kramer Electronics Ltd Web site www kramerelectronics com E mail info kramerel com P N 2900 000375 REV 3
20. etailed instructions on how to install and configure your Ethernet port see the Ethernet Configuration FC 11 guide pdf on our Web site http www kramerelectronics com 6 9 Controlling via the REMOTE Connector Connecting the REMOTE terminal block connector to a dry contact switch enables you to route an input to an output by remote control To route INPUT 1 to OUTPUT 8 Stage 1 REMOTE o To route input 1 to output 8 as an example see Figure 9 61234 1234 5678 Linputs_ OUTPUTS 1 Momentarily touch output 8 to Ground G Stage 2 2 Momentarily touch input 1 to REMTE Ground 1 1 1 1 11 61234 1234 5678 L INPUTS OUTPUTS Figure 9 Using the Remote Connector In the dual link mode only inputs 1 and 2 and outputs 1 to 4 are used as are the INPUT and OUTPUT selector buttons respectively Remote input PINs 3 and 4 and Input Selector buttons 3 and 4 are not used as well as Remote output PINs 5 to 8 and Output Selector buttons 5 to 8 19 Operating the VS A8HDxl 7 Operating the VS 48HDxl You can operate your VS 48HDxl using the T Front panel buttons RS 232 RS 485 serial commands transmitted by a PC to
21. f a function is performed via the machine s keyboard then these bits are set with the INSTRUCTION NO which was performed The instruction codes are defined according to the table below INSTRUCTION NO is the value to be set for N5 NO 2 BYTE Bit 7 Defined as 1 16 10 INPUT When switching ie instruction codes 1 and 2 the INPUT 7 bits is set as the input number which is to be switched Similarly if switching is done via the machine s front panel then these bits are set with the INPUT NUMBER which was switched For other operations these bits are defined according to the table 3 BYTE Bit 7 Defined as 1 O6 00 OUTPUT When switching ie instruction codes 1 and 2 the OUTPUT 7 bits is set as the output number which is to be switched Similarly if switching is done via the machine s front panel then these bits are set with the OUTPUT NUMBER which was switched For other operations these bits are defined according to the table 4 BYTE Bit7 Defined as 1 Bit 5 Don t care OVR Machine number override 4 0 MACHINE NUMBER Used to address machines in a system via their machine numbers When several machines are controlled from a single serial port they are usually configured together with each machine having an individual machine number If the OVR bit is set then all machine numbers will accept implement the command and the addressed machine will reply 1 You can download
22. front panel buttons in the AT ONCE mode see section 7 2 do the following 1 Press an OUTPUT button either 1 2 3 4 or ALL The selected OUTPUT button illuminates brightly as does the 7 segment display Press an INPUT button either 1 2 or OFF The selected input switches to the selected output and that input button illuminates brightly The digits displayed in the 7 segment display change as appropriate 7 2 Confirming Settings You can work in the AT ONCE or the CONFIRM mode see section 7 2 1 When the 8 48 operates in the AT ONCE mode pressing OUT IN combination implements the switch immediately In the CONFIRM mode the TAKE button must be pressed to authorize the switch In the AT ONCE mode you save time as execution is immediate and actions require no user confirmation However no protection is offered against changing an action in error In the CONFIRM mode You can key in several actions and then confirm them by pressing the TAKE button to simultaneously activate the multiple switches Every action requires user confirmation protecting against erroneous switching Execution is delayed until the user confirms the action Note that after ten seconds the VS 48HDxl will go to standby mode and the buttons and the 7 segment display will illuminate less brightly 1 For details of how to route an input to an output using the REMOTE connector see section 6 9 2 For immediate switch
23. ht SDI acceptors for example output 1 to a Preview display and output 8 to an HD SDI mixer Set the dipswitches see section 6 3 If required connect Genlock source to GENLOCK BNC connector The LOOP BNC connector to the GENLOCK connector of the next unit in the line and release the TERM button for looping Connect a PC and or controller if required to the RS 232 port see section 6 4 and or RS 485 port see section 6 5 and or ETHERNET connector see section 6 6 If required connect a remote dry contact switch refer to section 6 9 Connect the power cord 1 Switch OFF the power on each device before connecting it to your 5 48 After connecting your VS 48HDxl switch on its power and then switch on the power on each device 2 When only one output is required connect that output and leave the other outputs unconnected 3 Not illustrated in Figure 2 4 Pushed in terminates the input Release when the input extends to another unit 5 We recommend that you use only the power cord that is supplied with this machine 10 KRAMER SIMPLE CREATIVE TECHNOLOGY Connecting the VS 48HDxl 3G HD SD SDI 4x8 Matrix Switcher HD SD SDI Camera Preview SDI Monitor 3G HD Video Server HD SDI Mixer Figure 2 Connecting the 8 48 3G HD SD SDI 4x8 Matrix Switcher 11 Connecting the VS 48HDxl 3G HD SD SDI 4x8 Matrix Switcher 6 1 Connecting the VS 48HDxI in the
24. in blue The memory stores the data at that reference To confirm the setup press the INPUT OUTPUT button again To cancel the setup press the STO button once again 1 The timeout lasts for 10 seconds 22 KRAMER SIMPLE CREATIVE TECHNOLOGY Operating the VS A8HDxl 7 3 2 Recalling an Input Output Configuration To recall an input output configuration do the following 1 Pressthe RCL button The RCL button illuminates 2 Press the appropriate INPUT OUTPUT button the button corresponding to the setup That setup configuration blinks in the 7 segment display The memory recalls the stored data from that reference After pressing the same memory location the second time the settings take effect To cancel this action press the RCL button once again 7 4 Locking the Front Panel To prevent changing the settings accidentally or tampering with the unit via the front panel buttons lock your VS 48HDxl Unlocking releases the protection mechanism To lock the 8 48 e Press the LOCK button until the LOCK button illuminates The front panel is locked Pressing a button will have no effect To unlock the VS A48HDxI e Press the illuminated LOCK button until the LOCK button is no longer illuminated The front panel unlocks 1 The setup configuration is shown flashing in the 7 segment display but it is not implemented at this stage 2 Nevertheless even though the f
25. ing 21 Operating the VS A8HDxl 7 2 1 Toggling between the AT ONCE and CONFIRM Modes To toggle between the AT ONCE and CONFIRM modes do the following 1 Pressthe dim TAKE button to toggle from the AT ONCE mode in which the TAKE button is dim to the CONFIRM mode in which the TAKE button illuminates Actions now require user confirmation and the TAKE button illuminates 2 Press the illuminated TAKE button to toggle from the CONFIRM mode back to the AT ONCE mode Actions no longer require user confirmation and the TAKE button no longer illuminates 7 2 2 Confirming a Switching Action To confirm a switching action in CONFIRM mode where the TAKE button is illuminated do the following 1 Press an OUT IN combination The 7 segment Display blinks 2 Pressthe TAKE button to confirm the action The 7 segment Display no longer blinks The TAKE button turns off 7 3 Storing Recalling Input Output Configurations You can store and recall up to twelve setup configurations as well as the working mode using the four INPUT buttons and the eight OUTPUT buttons 7 3 1 Storing an Input Output Configuration To store the current status in memory do the following 1 Setthe working mode see section 6 2 2 Pressthe STO button The STO button illuminates 3 Press one of the 12 INPUT OUTPUT buttons this will be the setup in which the current configuration is stored The selected INPUT OUTPUT button illuminates
26. is sent to the PC If this code is sent to the switchers it will reset according to the present power down settings NOTE 2 These are bi directional definitions That is if the switcher receives the code it will perform the instruction and if the instruction is performed due to a keystroke operation on the front panel then these codes are sent For example if the HEX code 01 85 88 83 was sent from the PC then the switcher machine 3 will switch input 5 to output 8 If the user switched input 1 to output 7 via the front panel keypad then the switcher will send HEX codes 4l 81 87 83 to the PC When the PC sends one of the commands in this group to the switcher then if the instruction is valid the switcher replies by sending to the PC the same four bytes that it was sent except for the first byte where the DESTINATION bit is set high NOTE 3 SETUP 0 is the present setting SETUP 1 and higher are the settings saved in the switcher s memory i e those used for Store and Recall NOTE 4 The reply to a REQUEST instruction is as follows the same instruction and INPUT codes as were sent are returned and the OUTPUT is assigned the value of the requested parameter The replies to instructions 10 and 11 are as per the definitions in instructions 7 and 8 respectively For example if the present status of machine number 5 is breakaway setting then the reply to the HEX code 0B 80 80 85 would be HEX codes 4B 80 81 85 NOT
27. itness for a particular purpose are limited in duration to the length of this warranty EXCLUSION OFDAMAGES The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option Kramer shall not be liable for 1 Damage to other property caused by defects in this product damages based upon inconvenience loss of use of the product loss of time commercial loss or 2 Any other damages whether incidental consequential or otherwise Some countries may not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from place to place NOTE All products returned to Kramer for service must have prior approval This may be obtained from your dealer This equipment has been tested to determine compliance with the requirements of EN 50081 Electromagnetic compatibility EMC generic emission standard Part 1 Residential commercial and lightindustry EN 50082 Electromagnetic compatibility EMC generic immunity standard Part 1 Residential commercial and lightindustry environment CFR 47 FCC Rules and Regulations Part 15 Radio frequency devices Subpart B Unintentional radiators CAUTION Servicing the machines can only be done by
28. l features Cable equalization up to 350m for SD signals 140m for 1 5GHz HD signals and 120m for 3GHz HD signals Operation of up to 2 97Gbps enabling it to be used for standard definition high definition and the new 3G high definition serial digital video signals SD HD SDI SMPTE 259M 292M and 424M and 372M for dual link HD SDI signals compliance and support for data rates of 270Mbps 1483 5Mbps 1485Mbps and 2970Mbps Reclocking and equalization on each input storing and recalling setups and a TAKE button for the execution of multiple switches all at once Selector buttons that automatically light up in different colors green when the VS 48HDx detects a standard definition signal or blue when it detects a high definition signal The ability to switch genlocked video signals according to timing of the GENLOCK reference input Switching according to the Bi level or Tri level Genlock input according to SMPTE RP 168 The 8 48 is housed in a 19 1U rack mountable enclosure and is fed from a 100 240 VAC universal switching power supply The unit can be controlled via the front panel buttons or via An infrared remote control transmitter An infrared remote extension cable transmitter Remotely by RS 232 or RS 485 serial commands transmitted by a PC touch screen system or other serial controller The ETHERNET Remote contact closure for forced operation 1 Standard Definition SD means an NT
29. ntroller Set the address of the unit using the SETUP dipswitches 1 2 3 and 4 according to Table 3 When using a standalone VS 48HDxl unit set the address to 1 When connecting more than one VS 48HDxI unit set the address of the first machine the Master that is closest to the PC to 1 dipswitches are set to OFF Each additional VS 48HDxl unit must have a unique address Table 3 Machine Dipswitch Settings Address DIP1 DIP2 DIP3 DIP4 1 default OFF OFF OFF OFF 2 OFF OFF 3 OFF OFF ON OFF 4 OFF OFF ON ON 5 OFF ON OFF OoFF 6 OFF OFF ON 7 OFF JON ON OFF 8 OFF ON ON 14 KRAMER SIMPLE CREATIVE TECHNOLOGY Connecting the VS 48HDxl 3G HD SD SDI 4x8 Matrix Switcher 6 4 Controlling via RS 232 for example using a PC To connect a PC to the VS 48HDxl unit using the Null modem adapter provided with the machine recommended e Connect the RS 232 9 D sub rear panel port the VS 48HDXxl unit to the Null modem adapter and connect the Null modem adapter with a 9 wire flat cable to the RS 232 9 pin D sub port on your PC To connect a PC to the VS A48HDXxI unit without using a Null modem adapter e Connect the RS 232 9 pin D sub port on your PC to the RS 232 9 pin D sub rear panel port on the VS 48HDx unit as Figure 5 illustrates PIN 5 Connected to PIN 5 Ground PIN 3 Connected to PIN 2 PIN 2 Connected
30. number of inputs and outputs refers to the specific machine which is being addressed not to the system For example if six 16X16 matrices are configured to make a 48X32 system 48 inputs 32 outputs the reply to the HEX code 3E 82 81 82 i e request the number of outputs would be HEX codes 7E 82 90 82 ie 16 outputs 27 LIMITED WARRANTY Kramer Electronics hereafter Kramer warrants this product free from defects in material and workmanship under the following terms HOW LONGIS THE WARRANTY Labor and parts are warranted for seven years from the date of the first customer purchase WHOIS PROTECTED Only the first purchase customer may enforce this warranty WHATIS COVERED AND WHATISNOT COVERED Except as below this warranty covers all defects in material or workmanship in this product The following are not covered by the warranty 1 Any product which is not distributed by Kramer or which is not purchased from an authorized Kramer dealer If you are uncertain as to whether a dealer is authorized please contact Kramer at one of the agents listed in the Web site www kramerelectronics com 2 Any product on which the serial number has been defaced modified or removed or on which the WARRANTY VOID IF TAMPERED sticker has been torn reattached removed or otherwise interfered with 3 Damage deterioration or malfunction resulting from i Accident misuse abuse neglect fire water lightning or other acts of nature
31. our user friendly Software for Calculating Hex Codes for Protocol 2000 from the technical support section on our Web site at http www kramerelectronics com 25 Kramer Protocol 2000 For a single machine controlled via the serial port always set M4 MO 1 and make sure that the machine itself is configured as MACHINE NUMBER 1 Table 7 Instruction Codes for Protocol 2000 Note values in the table are decimal unless otherwise stated INSTRUCTION DEFINITION FOR SPECIFIC INSTRUCTION NOTE DESCRIPTION INPUT OUTPUT 0 RESET VIDEO 0 0 1 1 SWITCH VIDEO Set equal to video input Set equal to video output which is 2 which is to be switched to be switched 0 disconnect 0 to all the outputs 3 STORE VIDEO STATUS Set as SETUP 0 to store 2 3 1 to delete 4 RECALL VIDEO STATUS Set as SETUP 0 2 3 5 REQUEST STATUS OF A Set as SETUP Equal to output number whose 4 3 VIDEO OUTPUT status is reqd 15 REQUEST WHETHER SETUP SETUP 0 for checking if setup is defined 8 IS DEFINED 61 IDENTIFY MACHINE 1 video machine name 0 Request first 4 digits 13 3 video software version 1 Request first suffix 2 Request second suffix 10 Request first prefix 62 DEFINE MACHINE 1 number of inputs 1 for video 14 2 number of outputs 3 number of setups NOTES on the above table NOTE 1 When the master switcher is reset e g when it is turned on the reset code
32. ront panel is locked you can still operate via RS 232 or RS 485 as well as via the Kramer IR Remote Control Transmitter 23 Technical Specifications 8 Technical Specifications Table 4 includes the technical specifications Table 4 Technical Specifications of the VS 48HDxl INPUTS 4 SMPTE 259M 292M 424 372M for dual link HD SDI signals serial video 75Q on BNC connectors 1 GENLOCK 750 Hi Z on a BNC connector hi level or tri level sync OUTPUTS 8 equalized and reclocked SMPTE 259M 292M outputs 750 BNC connectors 1 Looped GENLOCK 750 Hi Z on a BNC connector OUTPUT LEVEL 800mVpp 75 ohms DATA RATE Up to 2 97Gbps CONTROLS Front panel RS 232 RS 485 ETHERNET infrared remote dry contact and panel lock POWER SOURCE Universal 100 240VAC 50 60Hz 22VA DIMENSIONS 19 inch W 7 inch D 1U H rack mountable WEIGHT 2 6kg 5 7lbs approx ACCESSORIES Power cord Null modem Adapter OPTIONS External remote IR receiver cable 9 Table of Hex Codes for Serial Communication Table 5 lists the Hex values for a single machine MACHINE 1 Table 5 VS 48HDxl Hex Codes for Switching via RS 232 RS 485 OUT 1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8 IN 1 01 01 01 01 01 01 01 01 81 81 81 81 81 81 81 81 81 82 83 84 85 86 87 88 81 81 81 81 81 81 81 81 IN2 01 01 01 01 01 01 01 01 82 82 82 82 82 82 82 82 81 82 83 84 85 86
33. simultaneously for 3 seconds until the three buttons flash to reset the machine to its default values 16 KRAMER SIMPLE CREATIVE TECHNOLOGY Connecting the VS 48HDxl 3G HD SD SDI 4x8 Matrix Switcher 6 7 Switching Genlocked Video Signals The genlock feature lets you switch genlocked video signals according to timing of the GENLOCK reference input Connect the GENLOCK cable If the HD input signal that is connected is one of the following it is necessary to set it up as follows e 108019 60Hz press and hold INPUT 1 button for 3 seconds The button will flash to indicate that the set up was completed e 1080199 50Hz or 720p 9 50Hz press and hold INPUT 2 button for 3 seconds The button will flash to indicate that the set up was completed e 720p 60Hz press and hold INPUT 3 button for 3 seconds The button will flash to indicate that the set up was completed When turning the machine ON the appropriate button will flash to indicate the latest setup last setup is saved 6 8 Controlling via ETHERNET You can connect the VS 48HDxI via the Ethernet using a crossover cable see section 6 8 1 for direct connection to the PC or a straight through cable see section 6 8 2 for connection via a network hub or network router 6 8 1 Connecting the ETHERNET Port directly to a PC Crossover Cable You can connect the Ethernet port of the VS A48HDxlI to the Ethernet port on your PC via a crossover cable with RJ 45 connectors
34. uch screen system or other serial controller Kramer RC IR2 Infrared Remote Control Transmitter Infrared remote extension cable transmitter ETHERNET Switching OUT IN Combinations Section 7 1 1 describes how to switch OUT IN combinations and section 7 1 2 how to switch OUT IN combinations in the dual link mode Note that The OUTPUT button color changes during routing according to the input button color red for standard definition or blue for high definition If no INPUT is connected to an OUTPUT that OUTPUT button will not illuminate If a source is connected to an INPUT that INPUT button will illuminate 7 1 1 Switch OUT IN Combinations To switch an input to an output via the front panel buttons in the AT ONCE mode see section 7 2 do the following 1 Press an OUTPUT button from 1 through 8 or ALL The selected OUTPUT button illuminates brightly as does the 7 segment display Press an INPUT button from 1 through 4 or OFF The selected input switches to the selected output and that input button illuminates brightly The digits displayed in the 7 segment display change as appropriate 1 For details of how to route an input to an output using the REMOTE connector see section 6 9 2 For immediate switching 20 KRAMER SIMPLE CREATIVE TECHNOLOGY Operating the VS A8HDxl 7 1 22 Switch OUT IN Combinations in the Dual Link Mode To switch an input to an output in the dual link mode via the
35. wer cord and then connect it again while pressing the ETH Factory Reset button The unit will power up and load its memory with the factory default definitions 3 See section 6 9 4 The ground connection is sometimes connected to the shield of the RS 485 cable In most applications the ground is not connected 5 Covered by a cap The 3 5mm connector at the end of the internal IR connection cable fits through this opening 6 Optional Can be used instead of the front panel built in IR receiver to remotely control the machine only if the internal IR connection cable has been installed Your VS A8HDxl 3G HD SD SDI 4x8 Matrix Switcher 4 1 Using the IR Transmitter You can use the RC IR2 IR transmitter to control the machine via the built in IR receiver on the front panel or instead via an optional external IR receiver The external IR receiver can be located 15 meters away from the machine This distance can be extended to up to 60 meters when used with three extension cables Before using the external IR receiver be sure to arrange for your Kramer dealer to insert the internal IR connection cable with the 3 5mm connector that fits into the REMOTE IR opening on the rear panel Connect the external IR receiver to the REMOTE IR 3 5mm connector 1 Model C A35M IRR 50 2 Model C A35M A35F 50 3 P N 505 70434010 S 8 KRAMER SIMPLE CREATIVE TECHNOLOGY Installing the VS 48HDxl in a Rack 5 Installing the VS
Download Pdf Manuals
Related Search