Metra 99-5819 mounting kit
Contents
1. Red 12V Batt Memory Yellow Ground Black Power Antenna Blue Amp Turn On Blue White Amp Ground Black White Illumination Orange Dimmer Orange White Right Front Gray Right Front Gray Black Left Front White Left Front White Black Right Rear Violet Right Rear Violet Black Left Rear Green Left Rear Green Black NOTE When a Black wire is not present ground radio to vehicle chassis All colors may not be present on all leads due to manufacturer s specifications 5 5 IS NOTES 99 5819 INSTRUCTIONS G 1 800 221 0932 m www metraonline com REV 04 23 10 COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST99 58192. INSTALLATION INSTRUCTIONS FOR PART 99 5819 APPLIGATIONS FORD 99 5819 KIT FEATURES e DIN Radio Provision With Pocket e ISO Mount Radio Provision With Pocket KIT COMPONENTS e A Radio Housing B Radio Housing Brackets C ISO Brackets D Trim Plate WIRING AND ANTENNA CONNECTIONS Sold Separately Wire harness e 70 5520 Ford harness 2003 up Antenna adapter e 40 CR10 Chrysler antenna 2002 up TOOLS REQUIRED Cutting Tool Phillips Screwdriver Socket Wrench ch 4 800 221 0932 www metraonline com COPYRIGHT 2010 METRA ELECTRONICS CORPORATION 5 som TABLE OF CONTENTS Dash Disassembly FORD F 150 XL Models Only 2009 10 1 Kit Assembly DIN Radio Provision With Pocket 2 SO Mount Radio Provision With Pocket 3 FINALASSEMDIV ER 4 Note Refer also to the instructions included with the aftermarket radio OPA PES E ES PORMER APCE da OCI HEA Acker shu iia den bey CER appi bag ke cee ODA ea RE GP re Er pale pri IG ua da ace HE BE ES LEE Que Redhat E ge Re RE dor MAR RIA ed ide tapes tirari amp dir het Oae 99 5819 DASH DISASSEMBLY FORD F 150 XL Models Only 2009 10 1 Disconnect the negative battery terminal to prevent an accidental short circuit 2 Unclip and remove the switch panel to the right of the cigarette lighter then remove the 1 9 32 screw exposed Figure A 3 Remo
3. of the radio housings pocket from the back of the housing forward Figure B Mount the ISO Brackets to the head unit with the screws supplied with the unit Figure C Slide the head unit into the radio opening until the side clips engage Figure D Snap the trim plate into the Radio Housing Figure D Continue to final assembly Ki LEE 99 5819 FINAL ASSEMBLY FINAL ASSEMBLY A Strip wire ends back 1 2 B Twist ends together C Solder D Tape 1 Locate the factory wiring harness in the dash Metra recommends using the proper mating adapter and making the connections as shown Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit 2 Re connect the negative battery terminal and test the unit for proper operation 3 Position the factory bracket aftermarket radio assembly into the dash and secure using the factory hardware 4 Secure the Double DIN radio housing to the sub dash using the factory hardware 5 Reassemble the rest of the dash in reverse order of disassembly FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit Metra recommends making connections shown below Strip Splice Solder Tape Isolate and individually tape off ends of any unused wires to prevent electrical short circuit METRA EIA WIRING CODE 12V Ignition Acc
4. ve the rubber pad at the top of the radio trim panel then remove the 2 9 32 screws exposed Figure B 4 Unclip and pull the side panels con taining the a c vents away from the radio trim panel Note It is not nec essary to remove the panels com pletely Figure C 5 Unclip and remove the radio trim panel Figure D 6 Remove 4 9 32 screws to remove the factory radio Continue to kit assembly Y Mena SA 99 5819 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET Note Refer also to the instructions included with the aftermarket radio Cut and remove the top 2 mounting holes off of the radio housing Note The notch in the housing should be on top Figure A A HERE TOP LEG ONLY Slide the included brackets onto the sides of the radio housings pocket from the back of the housing forward Figure B Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down Figure C Slide the aftermarket head unit into the cage and secure Figure D Continue to final assembly Y Melts 99 5819 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET Note Refer also to the instructions included with the aftermarket radio Cut and remove the top 2 mounting A holes off of the radio housing Note The notch in the housing je HERE TOP LEG ONLY should be on top Figure A CUT HERE TOP LEG ONLY Slide the included brackets onto the sides
Download Pdf Manuals
Related Search