Infocus SP-WALLKIT-01 project mount
Contents
1. 02 EE Figure 32 Visit the InFocus support site at www infocus com support Installation Instructions SP WALLKIT 01 4 Install two 1 4 20 x 1 2 button head security screws Q through holes in stop bracket and into holes in sliding nuts See Figure 33 stop bracket adapter plate x 4 one at a time Figure 34 Figure 33 5 Optional Remove projector from short throw projector mount according to projector interface instructions NOTE For most projectors it will be necessary to remove projector prior to install four security screws to projector bracket For ease of installation it is recommended to remove projector prior to performing the following steps 6 Remove one of four bolts from adapter plate See Figure 34 7 Install one 1 4 20 x 3 4 button head security screw R into hole vacated by removing bolt in Step 6 and into plastic spacer See Figure 35 8 Repeat Steps 6 7 for remaining three bolts one bolt at a time WARNING It is important to replace adapter plate bolts ONE AT A TIME or adapter plate could fall from mount during installation adapter plate Figure 35 9 Reinstall projector to mount Refer to Projector Installation Section for details Visit the InFocus support site at www infocus com support 15 SP WALLKIT 01 Installation Instructions InFocus 8802 002041 REV 00 2010 InFocus Corporation www inf2. WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to the short throw projector mounts up to and including the projector does not exceed 25 lbs 11 34 kg for the SP WALLKIT 01 32 78 MIN 58 21 MAX TRAVEL 28 52 5 10 38 3 OF LEVEL ADJ USIMENT ren E 57 8 02 28 BOLT CIRCLE 0 328 YP e nu ET 10 38 YAW ADJUSTMENT POINT 7977 128 7 5 07 56 L THREADS ONTO 1 1 2 NPT ROL AD USIMENTPOINT 44 INTERFACE LOCKING SWITCH PITCH ADJ USITMENT POINT 15 2 Visit the InFocus support site at www infocus com support Installation Instructions SP WALLKIT 01 LEGEND Pencil Mark Marcar con lapiz Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Stiftmarkierung Apertar fixado
3. drywall must be installed to a minimum of one stud left and right of the stud s being used to install the mount Drywall must be secured to studs with screws 12 on center A There must be a minimum of 1 7 8 48mm clearance inside wall Drywall 1 2 minimum Drywall Thickness Both Sides of Stud See hazard statement on page 2 Steel Stud 2 x 4 25ga minimum Stud type and structural strength must conform to the North American Specification for the Design of Cold Formed Steel Structural Members 362 125 18 C Shape S Stud Section Visit the InFocus support site at www infocus com support 5 SP WALLKIT 01 Installation Instructions Assembly And Installation Mounting Wall Bracket Concrete or Concrete Block 1 Determine mounting location on wall 2 Using mounting bracket B as a template mark four holes at the outer holes in bracket See Figure 1 3 Drill four 3 8 holes at marked locations in wall See Figure 1 front view o O ef A U Figure 2 Wood Studs 1 Determine mounting location on wall Use a stud finder to locate studs 2 Draw a dotted line down the center of the stud to be used for mounting O 3 Line up inner three holes on mounting bracket B with center of stud at desired mounting l
4. pitch of the entire arm can be adjusted See Pitch Adjustment Entire Arm Section for details Loosen Pitch adjustment locking screw using a 2 Phillips screwdriver See Figure 19 Turn Pitch micro adjustment screw right or left using a 2 Phillips screwdriver until image is properly aligned on target See Figure 19 Tighten Pitch adjustment locking screw using a 2 Phillips screwdriver See Figure 19 D e Figure 19 Roll Adjustment 1 Loosen ROLL adjustment locking screw using a 2 Phillips screwdriver See Figure 20 Turn ROLL micro adjustment screw right or left using a 2 Phillips screwdriver until image is properly aligned on target See Figure 20 Tighten ROLL adjustment locking screw using a 2 Phillips screwdriver See Figure 20 underside Geo Figure 20 Pitch Adjustment Entire arm 1 Remove two 8 32 x 3 4 Phillips pan machine screws F to free outer cover from mounting bracket See Figure 21 Figure 21 Slide outer cover of mount A away from mounting bracket to expose pitch adjustment screw See Figure 22 Figure 22 Loosen two 5 16 18 x 1 2 screws C on each side of mounting bracket See Figure 22 Loosen two bolts on either side of pitch adjustment screw See Figure 22 Adjust pitch adjustment screw until mount is at desired pitch level Turn clockwise to raise mounting
5. at www infocus com support 3 SP WALLKIT 01 Installation Instructions TOOLS REQUIRED FOR INSTALLATION B 222 1 2 12 7mm 3 8 9 5mm 7 32 5 6mm 7 16 ff 1 2 12 7mm 5 32 included security eo TEED 11 2mm e G 4 10 24 x 1 3 8 F 2 8 32 x 3 4 M 4 1 4 20 L 4 1 4 20 x 1 3 4 e a T 1 S 2 ap Alan 5 32 security security Gi Gi d C 2 D 4 n E 4 B 1 5 16 18 x 1 2 1 4 20 x 3 8 1 4 20 x 1 1 2 wall bracket S et di a ei H 4 J 4 K 6 concrete anchor 5 16 x 2 1 2 5 16 N 4 P 4 Q 2 R 4 1 4 1 4 20 x 1 2 1 4 20 x 3 4 security W 3 M4 x 12mm Ps U 1 interface bracket V 1 projector mount Visit the InFocus support site at www infocus com support Installation Instructions SP WALLKIT 01 Site Requirements WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT The figure below identifies the minimum requirements for installation of display mounts onto a steel stud structure If the structure or its components do not meet these requirements contact the mount manufacturer for specific instructions before attempting installation It should also be noted that no other equipment should be mounted to the same stud 16 or 24 on center Studs Display Mount Installation Location Must be centered on stud If back side of wall is unfinished
6. INSTALLATION INSTRUCTIONS Single Stud Short Throw Wall Mount InFocus SP WALLKIT 01 SP WALLKIT 01 Installation Instructions DISCLAIMER InFocus and its affiliated corporations and subsidiaries collectively InFocus intend to make this manual accurate and complete However InFocus makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind InFocus makes no representation of warranty expressed or implied regarding the information contained herein InFocus assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions DIMENSIONS WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty Itis the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided
7. acket See Figure 5 Drill three 1 2 holes at marked locations in wall See Figure 5 front view steel stud Figure 5 6 Hold metal channel on anchor M flat alongside plastic straps and slide channel through hole See Figure 6 Drywall Plastic Straps Figure 6 7 Holding plastic straps on anchor M pull anchor away from wall until channel rests flush behind wall making sure anchor channel is positioned vertically on stud See Figure 7 8 Slide plastic cap on anchor M towards wall until flange of cap is flush with wall See Figure 7 SP WALLKIT 01 Installation Instructions Plastic Cap Plastic Straps Steel Stud Drywall La Anchor Metal Channel SIDE VIEW Figure 7 Snap off plastic straps on anchor at wall by pushing side to side snapping off straps level with flange of plastic cap See Figure 8 Repeat steps 7 through 9 for each mounting hole Steel Stud Drywall o Plastic Cap y Anchor Metal Channel SIDE VIEW Figure 8 Place wall bracket over anchors and align mounting holes in display mount with holes in anchors See Figure 9 Insert 1 4 20 x 1 3 4 Phillips pan head screws L through 1 4 washer N corresponding mounting hole on wall bracket and int
8. ctor with interface bracket as shown in Figure 16 3 Lift projector so that screws with thumb nuts are aligned with mounting slots in mount base 4 Slide projector with interface bracket U onto mounting slots in projector mount V until screws are seated against the back of mounting slots See Figures 16 and 17 Figure 16 WARNING IMPROPER INSTALLATION CAN LEAD TO PROJECTOR FALLING RESULTING IN SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Make certain mounting slots in mount base slide under thumb screws and that screws are seated in the back of slots 5 Verify mounting screws are properly seated in mounting slots in mount base See Figure 17 6 Move locking lever to locked position See Figure 17 7 Insert key into lock and turn to secure projector to mount See Figure 17 reverse view Figure 17 Projector Mount Adjustments Yaw Adjustment 1 Loosen yaw adjustment locking screw using a 2 Phillips screwdriver See Figure 18 2 Turn Yaw micro adjustment screw right or left using a 2 Phillips screwdriver until image is properly aligned on target See Figure 18 3 Tighten Yaw adjustment locking screw using a 2 Phillips screwdriver See Figure 18 Figure 18 10 Visit the InFocus support site at www infocus com support Installation Instructions SP WALLKIT 01 Pitch Adjustment NOTE Pitch can be adjusted using the projector mount or the
9. level or turn counterclockwise to lower mounting level See Figure 22 Tighten two bolts on either side of pitch adjustment screw See Figure 22 Tighten two 5 16 18 x 1 2 screws C on each side of mounting bracket See Figure 22 Visit the InFocus support site at www infocus com support 11 SP WALLKIT 01 Installation Instructions Cable Management Optional 1 Remove two 88 32 x 3 4 Phillips pan machine screws F to free outer cover from mounting bracket See Figure 25 Figure 25 Figure 23 2 Slide outer cover of mount A away from mounting bracket See Figure 25 8 Slide outer cover of mount A back against mounting NOTE In most cases cable management covers will NOT bracket need to be removed in order to route cables from projector to the wall mount But for some thick cables 9 Reinstall two 8 32 x 3 4 Phillips pan machine screws F removing the covers may be necessary through holes on sides of outer cover See Figure 24 3 Remove cable management covers if necessary from short throw projector arm See Figure 26 bottom view 30 large cable cover projector Figure 24 Figure 26 12 Visit the InFocus support site at www infocus com support Installation Instructions SP WALLKIT 01 bottom view cable example Figure 27 4 Route projector cable s under mount cover and through 6 Replace
10. o anchor M and tighten until flush against mount DO NOT overtighten See Figure 9 Repeat steps 11 through 12 for remaining 2 mounting holes WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Overtightening of mounting hardware can damage the steel studs DO NOT overtighten mounting hardware Steel Stud Drywall N x 3 L x3 ev Wall bracket Anchor Metal Channel SIDE VIEW Figure 9 Installation to Wall Bracket 1 Liftshortthrow projector arm A up to mounting bracket B and hook top plate to upper notches on bracket See Figure 10 2 Slide lower plate into lower hooks on bracket See Figure 10 upper plate lower plate Figure 10 Visit the InFocus support site at www infocus com support Installation Instructions SP WALLKIT 01 3 Install two 5 16 18 x 1 2 hex head cap screws C through two 5 16 washers K and into holes on mounting bracket and projector mount See Figure 11 Figure 11 4 Slide outer cover of mount A back against mounting bracket See Figure 11 5 Install two 8 32 x 3 4 Phillips pan machine screws F through holes on sides of outer cover See Figure 12 Projector Installation WARNING Exceeding the weight capacity can result in serious personal injury
11. ocation See Figure 3 4 Using mounting bracket B as a template mark three holes at the inner three holes in bracket See Figure 3 Figure 1 5 Drill three 7 32 holes at marked locations in wall See 4 Install four concrete anchors H into drilled holes See Figure 3 Figure 2 5 Install four 5 16 x 2 1 2 hex head lag screws J through four 5 16 washers K outer holes of mounting bracket B and into concrete anchors H See Figure 2 front view wood stud o X3 D P X3 B Figure 3 6 Visit the InFocus support site at www infocus com support Installation Instructions SP WALLKIT 01 6 Install three 5 16 x 2 1 2 hex head lag screws J through three 5 16 washers K inner holes of mounting bracket and into drilled holes See Figure 4 Figure 4 Steel Studs IMPORTANT See Site Requirements section before proceeding with Steel Studs installation to ensure installation site meets requirements The drywall must have a minimum thickness of 1 2 1 Visit the InFocus support site at www infocus com support Determine mounting location on wall Use stud finder to locate steel studs Draw a dotted line down the center of the stud to be used for mounting Line up inner three holes on mounting bracket with center of stud at desired mounting location See Figure 5 Using mounting bracket as a template mark three holes at the inner three holes in br
12. ocus com 09 10 InFocus Corporation 13190 SW 68th Parkway Ste 200 Portland OR 97223
13. or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to the short throw projector mounts up to and including the projector does not exceed 25 lbs 11 34 kg for the SP WALLKIT 01 bottom view Figure 13 Projector Mount Installation 1 Line up mounting holes on projector mount V with corresponding holes on mounting plate See Figure 13 2 Install four 310 24 x 1 3 8 Phillips pan machine screws G through projector mount holes and into mounting plate See Figure 14 IMPORTANT If projector mount is NOT installed in the same direction as shown in Figure 14 ROLL adjustment screws will be inaccessible Figure 12 Visit the InFocus support site at www infocus com support mounting plate roll adjustment screws L d E ac Figure 14 SP WALLKIT 01 Installation Instructions Projector Installation to Mount WARNING IMPROPER INSTALLATION CAN LEAD TO PROJECTOR FALLING RESULTING IN SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT DO NOT substitute hardware Use only the hardware provided by the manufacturer 1 Secure interface bracket U to top of InFocus projector using three M4x12mm Phillips pan machine screws W and three M4 washers X See Figure 15 InFocus projector Figure 15 2 Orient proje
14. r Marcar com l pis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Aflojar elemento de fijaci n Perforar Befestigungsteil l sen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Bevestiging losdraaien Gat boren Desserrez les fixations Percez un trou Destornillador Phillips Ajustar Einstellen Ajustar Regolare Kruiskopschroevendraaier Afstellen Tournevis a pointe cruciforme Ajuster Llave de boca Quitar Gabelschl ssel Entfernen Chave de bocas Remover Chiave a punte aperte Rimuovere Steeksleutel Verwijderen Cl a fourche Retirez A mano Opcional Von Hand Optional Com a mao Opcional A mano Opzionale Met de hand Optie la main En option Hex Head Wrench Llave de cabeza hexagonal Security Wrench J Llave de seguridad Sechskantschl ssel Sicherheitsschl ssel Chave de cabe a sextavada Chave de seguran a Chiave esagonale Chiave di sicurezza Kreuzschlitzschraubendreher Chave de fendas Phillips CD Cacciavite a stella Zeskantsleutel Veiligheidssleutel Cl a t te hexagonale Cl de s curit Visit the InFocus support site
15. removed cable management covers if necessary short throw projector arm tunnel See Figure 27 Insert one side of cover into groove and press down firmly I S I on the cover on the other side until it snaps into the other 5 Optional Cables can be tied to inside of projector s front groove See Figure 29 cover using cable ties not included Route cables near front cover and wrap cable tie through slots on front cover and around cables See Figure 28 fM CS cable tie not included RULL LT DL Figure 29 route through slots and OC around cables Figure 28 Visit the InFocus support site at www infocus com support 13 SP WALLKIT 01 Installation Instructions Extension Adjustment 1 Loosen two bolts holding stop bracket in place on underside of short throw projector mount See Figure 30 Adjust mount to desired extension length See Figure 30 Tighten two bolts holding stop bracket to secure mount in desired position See Figure 30 bottom view Figure 30 Security Screw Installation Optional 1 Remove two 48 32 x 3 4 Phillips pan machine screws F See Figure 31 2 Install two 8 32 x 3 4 button head security screws S into holes in mount cover See Figure 31 14 3 Figure 31 Remove two bolts holding stop bracket in place on underside of short throw projector mount See Figure 32 stop bracket
Download Pdf Manuals
Related Search