Ultra Start 440 Series Automobile Alarm User Manual
Contents
1. Actuators Positive Type Door Locks Vehicle Fused 12V EI Green Blue EI Un Lock Unlock ee 5 Wire Reverse Polarity Type Door Locks N Fused 12V lol 87 87 a ial f a 8fa dh ml Blue 30 z C lol Vehicle Lock Unlock ro To Actuator Switch Un lock Negative Park Lights In some cases the park lights may flash erratically after installing the negative park light relay To correct this issue add a diode between the coil pins of the relay as shown Add IN4001 Diode as shown To Control Relay or Actuator Negative park light output2. Enter Program Mode Ignition ON OFF followed by Valet 2 times 2 Press amp release transmitter buttons in the following sequence 1 2 then 3 3 The siren will respond with the following 1 Chirp Active Arming 2 Chirps Passive Arming Repeat sequence to change selection Passive Active Arming To change settings 1 Enter Program Mode Ignition ON OFF followed by Valet 2 times 2 Press amp release transmitter buttons in the following sequence 3 3 then 2 3 The siren will respond with the following 1 Chirp Active Locks 2 Chirps Passive Locks Repeat sequence to change selection Door Lock Timing To change settings 1 Enter Program Mode Ignition ON OFF followed by Valet 2 times 2 Press amp release transmitter buttons in the following sequence 1 3 then 1 3 The siren will respond with the following 1 Chirp 3 Second Door Locks 2Chirps 0 75sec Pulses Repeat sequence to change selection Ignition Auto Locks To change settings 1 Enter Program Mode Ignition ON OFF followed by Valet 2 times 2 Press amp release transmitter buttons in the following sequence 1 3 then 2 3 The siren will respond with the following 1 Chirp Auto Lock Disabled 2 Chirps Auto Lock Enabled Repeat sequence to change selection PROGRAMMING Double Pulse Unlock To change settings 1 Enter Program Mode Ignition ON OFF followed by Valet 2 times 2 Press amp release transmitter buttons in the followin
3. 1 system Service Mode service Mode By remote Diagnostics Page 12 COMPONENTS Three Button Remote transmitter s 430 Series Control Module Four Button Remote transmitter s 440 Series Plug in Led Plug in Valet Switch Program Switch Multi Tone Siren 10 Pin Main Harness Installation Guide 2 pin Keyless Entry harness Owners Manual WIRING DIAGRAM 500ma Programmable unlock output Low current output for voltage inverter 500ma Programmable lock output Unlock Output 12v Constant Lock Output sy207 100q Connect to park lights 15amp Maximum Park Lights 500ma negative output When Armed Orange 500ma negative output Trunk Release Gray Connect to vehicles ignition wire Yellow Ignition Input Connect to constant power 20amp input 12 Volt Input Connect to Siren wire 2amp Maximum Siren Output Connect to chassis ground Ground Input z D 5 gt D a 3 n D 5 0 tn 0 Connect to door pin when opened Door Input Connect to door pin when opened Door Input Hood Input Connect to hood and or trunk pin Program Switch LED S QW lh Shock Sensor Adjustment Increase Sensitivity Turn the adjustment screw clockwise Decrease Sensitivity Turn the adjustment screw counter clockwise 500ma outputs are low current and are designed to activate relays WIRING CONNECTIONS 10 Pin Connector White Park lights Park lig
4. INSTALL GUIDE 430 and 440 Series Vehicle Security Systems REMOTE STARTERS CAR ALARMS WWW ULTRASTARTERS COM Technical Support Support ultrastarters com Note Some features may not be available on certain models FCC ID Notice This device complies with Part 15 of the FCC rules Operation is subject to the following conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation CAUTION Changes or modifications not expressly approved by the part responsible for compliance void the user s authority to operate this devise TABLE OF CONTENTS Table Of Contents Page 2 Wiring Diagram Page 3 Installation Tips Page 4 Pre Installation Suggestions Installation Suggestions Mounting The Module Installing The LED Installing The Program Button Under Hood Connections Mounting The Siren Wire Connectors Page 5 14 Pin Main Harness Connector 4 Pin Red Connector Keyless Entry 2 Pin Connector Red Plug in LED 2 Pin Blue Connector Plug in Program Button 3 Pin White Connector Aux outputs 4 Pin White Connector Addition sensor input Installation Page 6 7 Basic Installation Quick start shock Sensor Adjusting Test The System Programming Page 9 Program Overview Quick View Programming System Reset Operations Page 10 Transmitter Programming Battery Replacement Other Features Page 1
5. e then press and hold Step 3 The siren will respond with five chirps to confirm Transmitter Program Mode Note If the siren does not respond repeat Steps1 amp 2 Step 4 Continue to hold the Program Button and press lock button on each of the transmitter s to be programmed Maximum of 3 Different transmitter codes Step 5 The system will respond with a siren chirp each time a transmitter is programmed Exit After five seconds the system will exit transmitter program mode automatically NOTE You must program ALL of the transmitters to be used at one time For the owner s security any transmitters not programmed at this time will be erased from memory This system will store a maximum of three transmitter codes in memory Deleting Transmitters Follow the steps below to permanently delete a transmitter code from the system s memory Step 1 Turn the Ignition key ON then OFF Leaving Key Off Step 2 Press and release the Program Button twice then press and hold Step 3 The siren will respond with five chirps to confirm Transmitter Program Mode Note If the siren does not respond repeat Steps1 amp 2 Step 4 Continue to hold the Program Button and press lock button on only the transmitters that are intended for use on the system Maximum of 3 Different transmitter codes Step 5 The system will respond with a siren chirp each time a transmitter is programmed Exit After five seconds the system will exit transmitt
6. er program mode automatically All previous transmitter code are now deleted from the systems memory Basic Transmitter Functions Button 1 Press and release to arm the alarm and lock the doors Press and hold to activate Panic mode Press and release to deactivate triggered alarm TD HV 2 Button 2 Press and release to disarm and unlock the doors Press and hold to activate the Trunk Release Press and release to deactivate triggered alarm Button 3 Press and hold to activate the Car Finder Mode SYSTEM OPERATION Lock Doors amp Arm The Alarm 1 Press amp release the LOCK button on the remote transmitter 2 The park lights will flash and the siren will chirp once 3 The doors will lock 4 The LED will start flashing within five seconds Unlock Doors amp Disarm The Alarm 1 Press amp release the UNLOCK button on the remote transmitter 2 The park lights will flash and the siren will chirp twice 3 The doors will unlock 4 The LED will stop flashing Silent Arm And Disarm 1 Press amp release the button three then press amp release the lock or unlock button 2 lf the doors are locked this will unlock the doors without siren chirps the park lights will flash two times to confirm the doors have unlocked 3 If the doors are unlocked this will lock the doors without siren chirps the park lights will flash one time to confirm they have locked Trunk Release 1 Press and hold the UNLOCK button for t
7. g sequence 2 2 then 1 3 The siren will respond with the following 1 Chirp Double Pulse Unlock 2Chirps Single Pulse Unlock Repeat sequence to change selection Voltage Door Pin Sensing To change settings 1 Enter Program Mode Ignition ON OFF followed by Valet 2 times 2 Press amp release transmitter buttons in the following sequence 1 1 then 3 3 The siren will respond with the following 1 Chirp Voltage Sensing No Door Pin Connection Needed 2Chirps Door Pin Door Pin Connection Required Repeat sequence to change selection Chirp Delete To change settings 1 Enter Program Mode Ignition ON OFF followed by Valet 2 times 2 Press amp release transmitter buttons in the following sequence 2 2 then 1 3 The siren will respond with the following 1 Chirp Chirps Disabled 2Chirps Chirps Enabled Repeat sequence to change selection Shock Sensor Disable To change settings 1 Enter Program Mode Ignition ON OFF followed by Valet 2 times 2 Press amp release transmitter buttons in the following sequence 3 3 then 1 3 The siren will respond with the following 1 Chirp Shock Sensor OFF 2Chirps Shock Sensor ON Repeat sequence to change selection TRANSMITTER PROGRAMMING Transmitter Programming Follow the steps below to program the transmitters to the system s memory Step 1 Turn the Ignition key ON then OFF Leaving Key Off Step 2 Press and release the Program Button twic
8. hree seconds 2 The doors will unlock continue holding the unlock button three seconds the Trunk release will then activate The trunk release will be confirmed by one park light flash 3 For safety reasons the trunk release output will not activate when ignition key is in the On position Car Finder Mode 1 Press and hold the button for two seconds 2 The system will flash the park lights and chirp the siren five times This feature can help find your vehicle in a crowded parking lot Panic Mode 1 Press amp hold the LOCK button for three seconds 2 The park lights will flash and the siren will activate PANIC MODE DISABLE 1 Press LOCK button to disable the panic mode and to lock the doors 2 Press UNLOCK button to disable the panic mode and unlock the doors 3 Panic Mode will stay activated until disabled by the remote transmitter SYSTEM OPERATION Service Mode 1 The system must be disarmed and the ignition is turned OFF 2 Press and release the lock and unlock buttons at the same time then press and hold the lock button for five seconds 3 The system will respond with five chirps and park light flashes to confirm that the system is in Valet mode 4 The LED will stay ON steady to confirm Valet Mode Exit Service Mode 1 Press and release the lock and unlock buttons at the same time then press and hold the lock button for five seconds 2 The system will respond with two chirps and par
9. hrough a window and open the door The alarm will then activate repeat on all the doors 4 Test the Shock Sensor again and adjust if necessary 5 Insure that all additional features are working as intended 6 If necessary proceed to Program Mode to adjust the programmable outputs Your Basic Install Is Complete PROGRAM OVERVIEW Program mode allows you to adjust the settings and options of your system Your system has been intelligently designed by installers with years of experience The system s default settings do not require any program changes in most cases However this system does incorporate a advanced programming system with settings that can be easily adjusted Entering Program Mode To Enter Program Mode 1 Make sure ignition is in the off position 2 Within three seconds turn the key ON the OFF 3 Press and release the Program Button two times 4 The siren will chirp and the lights will flash once to confirm entering Program Mode Note f unit does not enter Program Mode turn ignition off and repeat steps 1 3 The ignition wire Yellow MUST be connected If it is not connected it will not be possible to enter the Program Modes Changing A Programmable Setting 1 Enter Program Mode As explained above 2 When in program Mode change the desired Program Setting by pressing the transmitter buttons in the following sequences The Systems Default Setting Are Shown In Bold Lettering Quick View Progra
10. ht output Orange When Armed Negative output when system is armed Grey Trunk Release Negative output for trunk release 500ma max Yellow Ignition Input Input from vehicles ignition wire RedMain Power Input Constant 12 Volt input Brown Siren Output Positive output for siren Black Ground Input System ground input Purple Door Input Positive door pin switch input Green Door Input Negative door pin switch input Blue Hood Input Negative input from hood pin switch 3 Pin Connector Red Green Door Lock Door Lock Output Programmable 12 Volt Output Output for voltage inverter Low Current Only Blue Door Unlock Door Unlock Output Programmable Recommended Installation Procedures Mounting the module Never mount the module in the engine compartment Select a location under the dash to install the main module Be certain that the module is securely attached and does not obstruct any serviceable areas Mount the module so that it cannot be seen if looking under the dash as it could be easily unplugged by a thief The module must be free from all moving parts Installing the LED Choose a location that will be highly visible when the LED is installed Most vehicles are equipped with knock out panels in the dashboard these panels are easily removable and can be easily replaced if necessary Once the location Is picked use drill bit and drill a hole through the panel Test fit the LED into the hole Plug the Led
11. into the Red connector on the main module Installing the Program Button Choose a location to mount the Program Button This location should be hidden and not visible from outside the vehicle Once the location of the switch is picked use a 1 4 drill bit and drill a hole Remove the nut and push the Program Button through the hole Replace the nut and tighten until the switch is secure Plug the Program Button into the Blue connector of the main module Under Hood Connections Route the hood pin optional and Siren wire through the firewall into the engine compartment Always try to pull the wires through a factory rubber grommet If drilling through the firewall BE CAREFUL Check for obstructions on both sides of the firewall After drilling use a snap in grommet to protect the wires from sharp edges Mounting the Siren Choose a location in the engine compartment that is away from high heat sources and direct exposer to water The siren should be mounted as well as grounded to solid metal Run the wiring for the siren so that it can not be seen or reached from below the vehicle BASIC INSTALLATION Step 1 Connect All Of the Following Wires 10 Pin Power Connector Black Ground Input System ground input Yellow Ignition Input Input from vehicles ignition wire Red Power Input Constant 12 Volt input Brown Siren Output Positive output for siren White Park lights Positive park light output Green Door Input Negative d
12. k light flashes to confirm that the system has exited Valet mode 3 The LED will turn OFF Note If the LED does not turn off check that all the door s are closed The LED stays On solid when a door is left opened Emergency Service Mode Emergency Service Mode temporarily disables the alarm system This feature can be used if the remote is lost or if the system malfunctions ENTERING VALET MODE 1 While the ignition is On press and hold the Service button for five seconds i The siren will chirps five times 2 Alarm functions will be disabled and the LED will be ON steady The door locks Press for i and trunk release are still operational EXITING VALET MODE 1 While the ignition is On press and hold the Service button for five seconds The siren will chirps two times 2 The system returns to normal operation Starter Disable The system has an optional starter disable output that can be connected by your dealer When the starter disable relay is installed and connected to the system the vehicle s starter will be disabled when the system is armed To activate the starter disable press the lock button on the remote The system will arm and the starter will no longer operate To deactivate the starter disable press the unlock button and the LEDS will stop flashing and the starter will be re enabled Door Lock Relays Negative Type Door Locks Vehicle To Control Lock Unlock Relay or Switch
13. mming Programmable Feature Press Buttons One Chirp Two Chirps Shock Sensor Status 43 43 41 Disabled Enabled Arm Disarm Chirps 42 41 41 Chirps Off Chirps On Ignition Auto Locks 1 3 2 Off On Door Lock Pulse Length 1 3 1 3 Second 75 Second Double Pulse Unlock 2 2 1 Two Pulses Single Pulses Door Input Voltage Sense 1 1 3 Voltage Door Pin Passive Active Locks 3 2 2 Active Passive Passive Active Arming 1 2 3 Active Passive system Reset 3 3 3 Confirmed by Three Siren Chirps System Reset This feature will reset the module to it s factory programmed default setting This feature will not delete transmitter codes from memory To Reset The System To Factory Defaults 1 Turn the ignition key On then Off 2 Press the Program Button two times The system will respond with two siren chirps 3 Press the transmitter buttons in the following order 3 3 3 The system will respond with three siren chirps to confirm the system has been re set to factory defaults PROGRAMMABLE FEATURES Enter Program Mode Entering program mode is done by the following steps 1 Make sure ignition is in the off position 2 Turn the ignition key ON OFF leaving key in the OFF position 3 Press and release the Valet button two times 4 The siren will chirp one time to confirm entering program mode If this does not happen turn ignition off wait five seconds and repeat steps 1 4 Passive Active Arming To change settings 1
14. oor pin switch input Purple Door Input Positive door pin switch input Test for door pin type or then connect the appropriate wire Green or Purple Step 2 Plug In The Module When all the connections are done the control module can be plugged in Before connecting the control module make sure the ignition is in the OFF position Plug in the main harness then any other connectors that were used Step 3 Test And Adjust The Shock Sensor To test the Shock Sensor 1 Press the Lock button once to arm the system 2 Wait five seconds then impact the vehicle Lighter impacts to the vehicle should trigger the warn away The siren will chirp three times A harder impact to the vehicle will trigger the full alarm The siren will activate for 60 seconds then turn off 3 To deactivate the alarm when triggered press the unlock button twice To Increase The Sensitivity Turn the adjustment screw Clockwise 1 4 turn then re test the sensitivity Repeat this procedure until the sensitivity of the system is at the appropriate level Do not set to sensitive To Decrease The Sensitivity Turn the adjustment screw Counter Clockwise 1 4 turn then re test the sensitivity Repeat this procedure until the sensitivity of the system is at the appropriate level Step 4 Test The System 1 Open all the vehicles windows 2 Press the Lock button to arm the system 3 Wait five seconds or until the dome light goes out then reach in t
Download Pdf Manuals
Related Search