U-Line CO2075DWR Ice Maker User Manual
Contents
1. o ON OFF Switch Figure 30 1 Put the ON OFF switch in the ON position Note There is an interior light in each drawer which illuminates when the drawer is opened 2 As soon as the ice maker mold reaches the proper temperature the ice maker mechanism will fill the mold with water Figure 31 Note The first cubes may be small because of air in the water line After two hours cubes will be standard size 3 The ice maker will continue to produce until the bin is full You may interrupt production by raising the bin arm into an upright and locked position see Figure 31 While the bin arm is locked the unit will maintain temperature for ice storage IMPORTANT It is possible that dirt or scale will dislodge in the water line Always throw away all ice cubes made during the first twenty four 24 hours of operation www U LineService com UFLINE ecoRPORATION U Temperature Controller The temperature controller Figure 32 is located in the top drawer It consists of an LED display two LED status indicator lights and three touchpad buttons The LED display shows the refrigerator temperature set point and is calibrated in degrees Fahrenheit The controller is factory programmed for a set point of 38 F for the top drawer which will show when the unit is first powered up The factory set point for the ice compartment is 0 F Figure 32. Mark and Drill New Mounting Holes 1 Remove one slide s mounting screws odo obo anna 2 Reposition the slide so it is the same distance from the bottom of the liner as the other slide Measure to confirm CJ Push Slide Upward or Downward Figure 22 3 Marknew drilling holes using different sets of mounting holes on the slide See Figure 22 Note Front location holes are shown Corresponding rear holes will also need to be marked 4 Drill all the new holes with a 30 drill bit 5 Remount the slide Re installation of Drawer NCAUTION Use care when handling the drawer Drawer edges drawer rail and the unit s slide may be sharp 1 Set the drawer s rails onto the slides 2 Re install the rails mounting screws See Figure 13 on Page 10 3 Plug in the drawer s connection wiring top drawer only 4 Go on to 6 Prepare Plumbing www U LineService com U U LINE CO2075DWR Ice Maker Refrigerator ecoRPORATION 6 Prepare Plumbing Plumbing installation must observe all state and local codes All water connections MUST BE made by a licensed gualified plumbing contractor Failure to follow recommendations and instructions may result in damage and or harm NWARNING To prevent accidental electrocution make certain that the floor surfaces surrounding the unit are dry whenever power is removed from or applied to the unit Water Supply Co
3. 16 CO2075DWR Ice Maker Refrigerator Start Up Troubleshooting Q Problem Unit does not appear to turn on when switch is set to ON A F Solution Make sure unit is plugged in and outlet has power circuit breaker has not tripped Q Problem Water does not appear to be flowing into unit A F Solution Check that the water is connected and turned on and the line is not obstructed Remember that the ice maker mechanism will not fill the mold with water until the mold reaches the proper temperature Q Problem The cubes produced during the first two to three hours of operation have been discarded New cubes still appear cloudy A Solution This is normal and is caused by air being trapped in the cube during fast freezing IMPORTANT See the User Manual s Troubleshooting Guide for more solutions 02 2005 U Um IN E CORPORATION Who to Call Service Information If the need for service arises contact the dealer from whom the unit was purchased State the Model Number and Serial Number and explain the problem The Model and Serial Number plate is located inside unit at upper right hand corner If you need to locate a service company you can go online at www U LineService com and search for a service company by zip code For more than four decades U Line has distinguished itself as the leader in built in undercounter ice making refrigeration and wine storage appliances Echelon SERIES O
4. Severe Adjustment Note The slides have extra mounting holes that may be used Mark and Drill New Mounting Holes 1 Remove the slide s mounting screws 2 Reposition the slide so it is the same distance from the front of the liner as the other slide Measure to confirm Push Slide Backward Figure 16 3 Mark new drilling holes using different sets of mounting holes on the slide See Figure 16 Note Front location holes are shown Corresponding rear holes will also need to be marked 4 Drill all the new holes with a 30 drill bit 5 Remount the slide Front to Back Adjustment See Figure 17 The drawer will need a Front to Back Adjustment if when viewed from the side the drawer front is cocked forward or back This is caused by the front slide mountings not being level with the rear slide mountings Not Aligned Front to Back Side View of Unit Figure 17 02 2005 CO2075DWR Ice Maker Refrigerator Minor Adjustment Note The mounting holes on the slide are slightly larger than the screws diameter Screws Should Be Loose 1 Loosen one slide s mounting screws 2 Level the slide 3 Retighten the screws See Figure 18 4 Repeat procedure for the other slide Figure 18 Severe Adjustment Note The slides have extra mounting holes that may be used Mark and Drill New Mounting Holes 1 Loosen
5. Safety Precautions IMPORTANT PLEASE READ all instructions completely before attempting to install or operate the unit e This unit requires connection to the water supply Improper hook up can result in substantial property damage If you are unsure of your ability to safely connect the water supply to the unit consult a licensed plumber for assistance This unit reguires connection to a grounded three prong polarized receptacle that has been placed by a gualified electrician in accordance with applicable electrical codes Safety Alert Definitions Safety items throughout this guide are labeled with a Danger Warning or Caution based on the risk type AMDANGER Danger means that failure to follow this safety statement will result in severe personal injury or death NWARNING Warning means that failure to follow this safety statement could result in serious personal injury or death NCAUTION Caution means that failure to follow this safety statement may result in minor or moderate personal injury property or eguipment damage 02 2005 CO2075DWR Ice Maker Refrigerator General Precautions Use this appliance for its intended purpose only and follow these general precautions along with those listed throughout this guide NWARNING SHOCK HAZARD Electrical Grounding Reguired e Keep the unit unplugged throughout installation except during testing Never remove the round grounding
6. not level the ice mold will not fill evenly 1 Use a level to check the levelness of the unit from front to back and from side to side Level should be placed along top edge and side edge as shown see Figure 27 A o gt gt Figure 27 2 If the unit is not level adjust the feet on the corners of the unit as necessary see Figure 28 geen Foot to Adjust Figure 28 3 Check the levelness after each adjustment and repeat the previous steps until the unit is level Go on to 9 Install the Unit Installation Tip If the room floor is higher than the floor in the cut out opening adjust the rear feet to achieve a total unit rear height of 1 8 less than the opening s rear height Shorten the unit height in the front by adjusting the front feet This allows the unit to be gently tipped into the opening Readjust the front feet to level the unit after it is correctly positioned in the opening www U LineService com y U LINE CO2075DWR Ice Maker Refrigerator ecoRPORATION 9 Install the Unit Horizontal Mounting Left Side Shown Installation of the CO2075DWR 1 Make sure the ON OFF switch is in the OFF position Countertop or Wall Header Open the water supply valve in the main water source Plug in the power cord Powe ws Gently push the unit into position Be careful not to kink the water sup
7. with seamless full wrap stainless steel fronts that do not accept custom panels sculpted stainless steel handles and black vinyl clad cabinets Please carefully follow the directions that apply to your unit and your intended design Tools Materials Reguired e Wrenches e Screwdrivers slotted and Phillips head e 1 4 inch OD copper tubing and shut off valve for water supply line e 1 4 inch thick drawer panel material and cutting tools Black units e 3 4 inch thick drawer panel overlay material cutting tools drill and bits Black units Inspection Unwrap and inspect the unit on a flat level surface capable of supporting its entire weight Removing Protective Coating All Models The protective coating covering the inside of the top drawer must be removed before using Stainless Steel Models When inspecting installing a Stainless Steel unit the protective coating covering the drawer fronts must be removed Start at a corner of the drawers and pull back the protective coating to remove it from the drawer fronts After all the protective coating has been removed from the drawers clean all Stainless Steel surfaces with Claire Stainless Steel Polish and Cleaner or comparable product or a mild detergent and warm water solution and soft cloth Do NOT use abrasive cleaning agents Note If cleaning with mild detergent and warm water solution and soft cloth the unit MUST be treated with Claire Stainless Steel Poli
8. 2 To display actual temperature in the refrigerator press the WARMER button momentarily A solid status indicator light 1 Figure 32 will show the air temperature reading in the cabinet for approximately 10 seconds To adjust the temperature set point press the SET TEMP button momentarily the display will flash Press the WARMER or COOLER button as desired to change the set point When the desired set point shows on the display wait 10 seconds and the new set point will be saved Wait 24 hours for the temperature to stabilize before checking the actual temperature again The refrigerator set point range is 34 F to 45 F To check the temperature in the ice compartment press the WARMER button momentarily and then press and hold COOLER for three seconds For more information see the User Manual For a quick reference to indicator light status see the table below Indicator Light Status e Solid e Refrigerator temperature displayed e Flashing e Not Applicable 2 e Solid e Freezer temperature displayed e Flashing e Open thermistor call for service Other Settings Other settings for the unit are factory preset No adjustments should be necessary at this time See the User Manual for information on e Removing the upper drawer s storage bin e Removing the lower drawer s ice bucket e Adjusting the upper drawer s organizer left to right or front to back www U LineService com
9. UFLINE CORPORATION Echelon Series Installation Guide EE CO2075DWR Combo Drawer Model Ice Maker Refrigerator www U LineService com Phone 414 354 0300 FAX 414 354 7905 Service amp Parts Tech Lines Phone 800 779 2547 FAX 414 354 5696 OnlineService U Line com 2005 U Line Corporation 02 2005 U U LINE ecoRPORATION Contents Exterior Cleaning VYYY Y Y Y ud 4 Cut Out Dimensions YY Y YG 4 Product Dimensions Y G 5 Clearances Information 5 Other Site Reguirements 6 No Custom Drawer PanelS 7 Custom 1 4 Drawer Panel Inserts 7 Full Overlay Drawer Panels 8 Checking Drawer Alignment 9 Adjusting Drawer Alignment 10 Water Supply Connection 12 Electrical Specifications 13 Leveling Information V Y y 13 Installation Tip Y Y YF eee 13 Installation of the CO2075DWR 14 Anti Tip Kit Installation 14 Installation Troubleshooting 15 Initial Start Up Y ug 15 Start Up Troubleshooting 16 Service Information 0 ccc cece ene eens 17 www U LineService com CO2075DWR Ice Maker Refrigerator 1 Follow
10. card 9 9 3 Repeat for the other side Note The bracket should be flush with the surface it is being attached to If it is not loosen the screws and slide the bracket against the mounting surface Tighten screws securely www U LineService com 14 02 2005 CO2075DWR Ice Maker Refrigerator 4 Using two of the screws C supplied fasten the screws through the bracket and into the counter cabinet or wall IMPORTANT Certain cabinets or countertops may require special fasteners or additional wood blocking to anchor properly NCAUTION Make sure the screws are back far enough so they do not damage any exposed front surface of the cabinet Installation Troubleshooting O Problem Water is leaking under the unit z Solution A water leak under the unit is most likely caused by a bad connection in the water supply line Make sure the water line s brass fitting is screwed tight to its valve and threaded correctly O Problem The drawer remains open unless it is pushed closed A Solution The drawer should be self closing when it is open approximately 8 If this is not re check leveling from front to back of the unit and readjust if necessary 02 2005 U U LINE ecoRPORATION 10 Start Up for the First Time Initial Start Up Once installation and leveling is complete the unit is ready for initial start up and operation The ON OFF switch is located in the front grille see Figure 30
11. d Cleaner or comparable product to prevent further problems e Use of abrasive pads such as Scotchbrite will cause the graining in the stainless to become blurred e Rust that is allowed to linger can penetrate into the surface of the stainless steel and complete removal of the rust may not be possible 3 Prepare Site Your U Line product has been designed for built in installation Your unit does not reguire additional air space for top sides or rear However the front grille must NOT be obstructed and clearance is reguired for water and electrical connections in the rear Note Unit can NOT be installed behind a closed cabinet door Cut Out Dimensions a e See Electrical Specifications for Power Supply 23 11 16 Figure 1 Follow the cut out drawing in Figure 1 The 24 3 16 width allows 1 4 for ease in installation and removal of the unit 24 is the counter depth in most installations The unit is 23 11 16 deep including the drawer and not the full handle or 3 4 overlay see Figure 2 www U LineService com 02 2005 CO2075DWR Ice Maker Refrigerator Product Dimensions 25 13 16 Including Handle T 23 11 16 Stainless Steel S 24 7 16 Including Overlay u wae NEN y Xt Sis T N co 15 16 Pg Wood Overlay Figure 2 Please note that the unit has adjustable feet that can add one additional inch to heigh
12. hardware is not counter bored Back of Wood Panel Drawer Panel Side of Wood Panel Bottom of Wood Panel 3 8 Bottom Both Sides Figure 9 2 Place and tape the existing drawer panel on the back of the overlay panel see Figure 9 3 Drill the five holes 5 32 drill 3 8 deep through both panels according to Figure 10 Top of Vinyl Coated Wood Panel Steel Panel y 5 32 x 3 8 Deep 5 Places lt tt 7 8 je Figure 10 02 2005 CO2075DWR Ice Maker Refrigerator NCAUTION It is mportant to ensure that all drilled holes are drilled to the correct depth in order to avoid splits in the wood when hardware is installed 4 Remove tape adjoining the panels and enlarge the five holes in the overlay panel using a 0 201 7 drill 5 Attach the drawer panel to the overlay panel using 10 x 5 8 wood screws and nylon spacers The nylon spacers fit between the overlay panel and the door panel as shown in Figure 11 The spacers allow the original drawer panel to slide back into the 1 4 thick drawer front reveal channel Typical Wood Panel Drawer Panel 10 x 5 8 Round Head Screw Five Required Plastic Spacer Five Required Figure 11 IMPORTANT Drawer panel and overlay panel must be aligned properly or the drawer will not operate correctly Assembling the Drawer Front 1 Install the assembled panel by sliding the origi
13. l Preparation Full overlay drawer panels completely cover the drawer fronts and handles to give a built in appearance Black units are shipped ready for full overlay installation Note For standard installations both drawers mount the same and a 1 2 gap is achieved between drawers 1 Cut the overlay to the following dimensions Full Overlay Dimensions Width 23 J 4 Height 14 3 4 IMPORTANT The thickness of the wood overlay panel must be 3 4 The door panel must not weigh more than 20 lbs Drawer Panel Installation Removing Existing Drawer Fronts 1 Open drawer Pull drawer gasket out of groove top edge of drawer only Start in the middle and pull outward moving toward the edge see Figure 7 This may take some force 2 Remove and save the two screws located at the ends of the handle see Figure 8 Remove the handle Handle Screw Figure 7 Figure 8 3 Remove existing panel and cardboard spacer Discard the spacer www U LineService com CO2075DWR Ice Maker Refrigerator Attaching the Full Overlay Panel 1 If user supplied cabinet handles will be used attach their hardware to the overlay panel at this time IMPORTANT User supplied cabinet handles MUST be counter bored to make sure mounting hardware is below surface of overlay panel Failure to do so can cause damage to overlay panel and or drawer Overlay panel will not sit flush to drawer if mounting
14. nal door panel back into the drawer front 2 Replace the handle assembly and secure with the two screws removed in Step 2 under Removing Existing Drawer Fronts 3 Starting at the corners and working toward the center push the drawer gasket back into place Go on to 5 Adjust Drawers 02 2005 U U LINE ecoRPORATION 5 Adjust Drawers Checking Drawer Alignment The unit s drawers are aligned at the factory before shipment However their alignment could have been disturbed during shipment or during overlay panel installation Aligned Front to Back 5 ba Aligned Side to Side Aligned Top to Bottom Figure 12 See Figure 12 Check each drawer to confirm that it is aligned e Side to Side When viewed from the top the drawer front should be sguare with the sides of the cabinet e Front to Back When viewed from the side the drawer front should be straight with the cabinet s sides not cocked forward or back e Top to Bottom When viewed from the front the drawer should be level horizontally If both drawers are properly aligned go on to 6 Prepare Plumbing If either drawer is not aligned carefully follow instructions to remove that drawer make the necessary adjustment and re install the drawer www U LineService com TW UFLINE ecoRPORATION Adjusting Drawer Alignment NWARNING SHOCK HAZARD The unit must be unplugged from the wall outlet during drawer
15. nnection When connecting the water supply follow these guidelines e Review the local plumbing codes before you install the unit e Connect to the cold water supply e The water pressure should be between 20 and 120 psi e Install a shut off valve in the 1 4 inch OD water supply line e Connect sufficient tubing to the unit so that tubing may be looped allowing the unit to be removed for cleaning and servicing see Figure 25 However make certain that the tubing is not pinched or damaged during installation e U Line recommends the use of copper tubing for installation To connect to water supply 1 Install the 1 4 inch OD copper water line from the main water source see Figure 23 Water Connection Figure 23 Figure 24 2 Locate the compression fitting and ferrule packed with the unit Slide the compression fitting and ferrule over the 1 4 inch OD water supply line Do not use thread sealing compound or tape Using two wrenches tighten the compression fitting on the supply line see Figure 24 3 Carefully bend the water supply line into position and connect the line to the solenoid valve see Figure 25 Avoid kinking the water supply line Figure 25 IMPORTANT Normal operation creates some vibration A water supply line contacting cabinet wall may cause excessive noise during operation or damage to the line 4 Allow extra water
16. one slide s rear mounting screws 2 Remove the slide s front mounting screws 3 Reposition the slide so it is level Level the Slide 4 Mark new front drilling Figure 19 holes using a different set of mounting holes on the slide See Figure 19 5 Drill the new holes with a 30 drill bit 6 Remount the slide 7 Repeat procedure for the other slide Top to Bottom and Left to Right Adjustment Not Aligned Left to Right l l Top View of Unit Front View of Unit Figure 20 See Figure 20 The drawer will need a Top to Bottom Adjustment if when viewed from the front the drawer is not level horizontally Viewed from the top one side will protrude This is caused by one of the slides being mounted higher than the other slide on the unit s liner 02 2005 U U LINE ecoRPORATION Minor Adjustment Note The mounting holes on the slide are slightly larger than the screws diameter Loosen Mounting Screws 1 Loosen one slide s mounting screws 2 Push the slide upward or downward to match the position of the other slide Upward or Push Slide Downward 3 Retighten the screws See Figure 21 Figure ai 4 Repeat the procedure with the other slide if necessary Severe Adjustment Note The slides have extra mounting holes that may be used
17. ply line or entangle the electrical cord 5 Re check the leveling from front to back and side to side Make any necessary adjustments The unit s top surface should be approximately 1 8 below the countertop Anti Tip Kit Installation Vertical Mounting NWARNING Left Side Shown Cabinet or Wall Stud e The Anti Tip Kit must be installed on this unit before it is used e Additional blocking or special fasteners may be reguired for installation Installer is responsible for secure attachment to prevent the unit from tipping e Make sure the mounting screws attaching the unit to the counter cabinet or wall are deep enough into the mounting surface to support the weight of the drawers and the items that will be inside the drawers Never use the drawers as steps or as a shelf to support more than the drawers content Serious personal injury could occur After leveling the unit must be secured to a counter a cabinet or a wall to prevent tipping 1 Open the upper drawer to expose the six screws A installed at the top two corners three at each corner 2 Insert the screws through the anti tip bracket B and Remove the appropriate screws for horizontal or attach the bracket to the unit Tighten screws securely vertical mounting see Figure 29 Do not dis
18. prong from the plug and never use a two prong grounding adapter e Never use an extension cord to connect power to the unit e Always keep your working area dry NWARNING The Anti Tip Kit must be installed on this unit before it is used Never use the drawers as steps or as a shelf to support more than the drawers contents Serious personal injury could occur NCAUTION e Use care when moving and handling the unit Use gloves to prevent personal injury from sharp edges e Do not lift the unit by the drawer handle e Do not install the unit behind closed doors or in any way that would obstruct airflow to the front grille which may cause the unit to malfunction 02 2005 U U LINE ecoRPORATION 2 Inspect and Plan You have received a carton containing your CO2075DWR Combo Drawer Model Ice Maker Refrigerator with a package inside containing a User Manual a Product Registration Card water connection parts and Anti Tip Kit Complete and mail the Product Registration Card or register online at www U LineService com Once your unit is installed keep the User Manual and this Installation Guide in a safe place for future reference Your unit is Black or Stainless Steel Black units have drawers with top handles designed for the installation of full overlay drawer panels When full overlay panels will not be used replacement handles MUST be installed part number 11926 4 BLK Stainless Steel units have drawers
19. rature must be at least 50 F 10 C but must not exceed 110 F 40 C High ambient temperature ranges and warmer water supply will cause reduced ice production Units may be installed outdoors in a covered area The unit must not be located near heat generating eguipment or in direct sunlight 02 2005 CO2075DWR Ice Maker Refrigerator 4 Prepare and Install Drawer Panel Black Units Only Two types of custom drawer panels can be installed on your Black unit to harmonize with or accent the surrounding d cor Custom 1 4 Inserts or Full Overlays Black units may also be installed with no custom drawer panel No Custom Drawer Panels When full overlay drawer panels are not used replacement handles part number 11926 4 BLK must be installed on each drawer To replace the handle when no custom panel will be installed follow the instructions under Custom 1 4 Drawer Panel Inserts Door Panel Installation below disregarding Steps 4 and 5 Custom 1 4 Drawer Panel Inserts Drawer Panel Preparation Custom drawer panels can be inserted into the drawer fronts Custom drawer panels can be flat or raised as long as the maximum panel thickness where inserted into the drawer front reveal channel is 1 4 thick For raised panels the depth of the reveal is 1 4 on all four sides IMPORTANT Raised panels will reduce the drawer s front clearance if the unit is installed facing an appliance or structure see Page 5 C
20. removal adjustment and re installation 1 Confirm that the unit is unplugged from wall outlet Mounting 2 Unplug the drawer s connection wiring top drawer only 3 Remove the mounting screws See Figure 13 4 Pull the drawer completely out of the unit Figure 13 NCAUTION Use care when handling the drawer Drawer edges drawer rail and the unit s slide may be sharp IMPORTANT Drawer adjustments are made by moving the slide that carries the drawer s rail Minor adjustments may be made by loosening one of the slide s mounting screws adjusting the slide and retightening the screw Severe adjustments may be made by removing the slides mounting screws drilling new mounting holes and remounting the slide Side to Side Adjustment See Figure 14 The drawer will need a Side to Side Adjustment if when viewed from the top the drawer front is not sguare with the sides of the cabinet This is caused by one of the slides being mounted too far forward on the unit s liner Not Aligned Side to Side Top View of Unit Figure 14 www U LineService com CO2075DWR Ice Maker Refrigerator Minor Adjustment Note The mounting holes on the slide are slightly larger than the screws diameter Loosen Mounting Screws 1 Loosen the slide s mounting screws 2 Push the slide backward Push Slide Backward 3 Retighten the screws See Figure 15 Figure 15
21. rigins SERIES U Line Corporation located in Milwaukee WI is a family operated manufacturer of built in undercounter icemakers Combo icemaker refrigerators Wine Captain wine storage units refrigerators refrigerated drawers and refrigerator freezers 2005 U Line Corporation Publication No 30058E 02 2005 Rev A
22. sh and Cleaner or comparable product to prevent discoloration www U LineService com U U LINE CO2075DWR Ice Maker Refrigerator ecoRPORATION Exterior Cleaning As Reguired Black Models e The drawers grille and cabinet may be cleaned with a mild detergent and warm water solution Do not use solvent based or abrasive cleaners Use a soft sponge and rinse with clean water Wipe with a soft clean towel to prevent water spotting Stainless Steel Models e Stainless steel models can discolor when exposed to chlorine gas pool chemicals salt water or cleaners with bleach e Keep your stainless steel unit looking new by cleaning with a good quality all in one stainless steel cleaner polish on a monthly basis For best results use Claire Stainless Steel Polish and Cleaner which can be purchased from U Line Corporation The part number is 173348 Comparable products are acceptable Frequent cleaning will remove surface contamination that could lead to rust Some installations may require cleaning on a weekly basis Do not clean with steel wool pads Do not use cleaners that are not specifically intended for stainless steel this includes glass tile and counter cleaners e If any surface discolors or rusting appears clean it guickly with Bon Ami or Barkeepers Friend Cleanser and a non abrasive cloth Always clean in the direction of the grain Always finish this process with Claire Stainless Steel Polish an
23. supply line length to provide slack for easy removal from the recessed area see Figure 25 This will also safeguard against kinking the line 5 Go on to 7 Prepare Power Supply www U LineService com 02 2005 CO2075DWR Ice Maker Refrigerator 7 Prepare Power Supply Electrical Specifications NCAUTION Electrical installation must observe all state and local codes This unit reguires connection to a grounded three prong polarized receptacle that has been placed by a gualified electrician The unit reguires a grounded and polarized 115 VAC 60 Hz 15A power supply normal household current An individual properly grounded branch circuit or circuit breaker is recommended GFCI ground fault circuit interrupter is usually not reguired for fixed location appliances and is not recommended for your unit because a GFCI could be prone to nuisance tripping However be sure to consult your local codes See Figure 26 for recommended receptacle location 23 11 16 Figure 26 NWARNING SHOCK HAZARD Electrical Grounding Reguired e Never remove the round grounding prong from the plug and never use a two prong grounding adapter e Never use an extension cord to connect power to the unit Go on to 8 Level the Unit 02 2005 UFLINE ecoRPORATION 8 Level the Unit Leveling Information IMPORTANT It is extremely important that the unit is level If it is
24. t during leveling or to match adjacent cabinets see Figure 28 on Page 13 02 2005 U LINE Clearances Information The unit must be installed in a wall or under a counter top to allow for the installation of the Anti Tip Kit see Page 14 N WARNING The Anti Tip Kit must be installed on this unit before it is used Never use the drawers as steps or as a Shelf to support more than the drawers contents Serious personal injury could occur The unit is designed so it can be installed next to a wall on either side see Figure 3 e Cabinet or Wall Figure 3 www U LineService com U U LINE ecoRPORATION The drawer unit can be installed with an appliance or fixture located in front of it as long as there is adeguate clearance for the drawer to be opened and removed when servicing see Figure 4 Note U Line recommends you consider additional clearance in front of the open drawer for convenience Figure 4 www U LineService com CO2075DWR Ice Maker Refrigerator Other Site Reguirements Power Supply The unit reguires a grounded and polarized 115 VAC 60 Hz 15A circuit normal household current See Electrical Specifications on Page 13 Water Supply The unit reguires a 1 4 inch OD water supply line and a shut off valve For more information see Page 12 Environmental Reguirements The surrounding air tempe
25. ut the panel inserts to the following dimensions Custom 1 4 Dimensions Width 23 1 32 Height 12 15 16 The door panels must not have a total weight of more than 20 lbs 02 2005 U U LINE ecoRPORATION Drawer Panel Installation Install the insert as follows NCAUTION Use care when handling the insert Insert edges may be sharp 1 Open drawer Pull drawer gasket out of groove top edge of drawer only Start in the middle and pull outward moving toward the edge see Figure 5 This may take some force 2 Remove the three screws behind the gasket and save Carefully pull the top handle up and off and discard Figure 5 3 Remove and save the two outside screws and the lower handle see Figure 6 A Standard 4 Remove and discard Handie existing panel and cardboard spacer 5 Slide custom drawer panel insert into 1 4 inch channel in drawer front 6 Attach the full handle to the lower handle using the three screws removed in Step 2 Figure 6 7 Holding drawer gasket out of the way replace handle on drawer making sure it is seated properly on insert and that screw holes line up 8 Install two small screws removed in Step 3 9 Starting at the corners and working inward push drawer gasket into place on drawer Go on to 5 Adjust Drawers www U LineService com U U LINE ecoRPORATION Full Overlay Drawer Panels Drawer Pane
Download Pdf Manuals
Related Search