Dodge 2007 LX Magnum Automobile User Manual
Contents
1. Loose the ring nut to set it in the cor rect position e Connect the water inlet hose to the cold water tap with 3 4 thread CAUTION Make sure that there are no leaks from the couplings Do not use an extension hose if the inlet hose is too short Con tact the service centre for the re placement of the inlet hose Water stop device ENGLISH 33 The inlet hose has a water stop device This device prevents water leaks in the hose because of its natural ageing The red sector in the window A shows this fault If this occur close the water tap and contact the service centre to replace the hose WATER DRAINAGE There are different procedures to con nect the drain hose With the plastic hose guide e On the edge of a sink e Make sure that the plastic guide can not move when the appliance drains Attach the guide to the water tap or the wall e To a stand pipe with vent hole Refer to the illustration Directly into a drain pipe at a height of not less than 60 cm and not more than 100 cm The end of the drain hose must always be ventilated i e the inner diameter of the drainpipe must be larger than the external diameter of the drain hose 34 Without the plastic hose guide e To a sink spigot Refer to the illustration Put the drain hose in the spigot and tighten it with a clip Make sure that the2. The programme does not start The spin phase is off The filter of the drain pump is blocked Balance problems with the laundry load The mains plug is not connected in the mains socket Set the spin programme Clean the filter of the drain pump Refer to Care and clean ing Adjust manually the items in the tub and start the spin phase again Put in the mains plug Blow out fuse in the household fuse box Replace the fuse You did not press button The delay start is set The Child Lock function is activated Press button JZ To start immediately the pro gramme cancel the delay start Deactivate the Child Lock func tion There is water on the floor Leakages from the cou plings of the water ho ses Make sure that the couplings are tight Leakages from the drain pump The water drain hose is damaged Make sure that the drain pump filter is tight Make sure that the water inlet hose has no damages You cannot open the appliance door The washing programme is in operation Let the washing programme end There is water in the drum Set the drain or the spin pro gramme The appliance makes an unusual noise Incorrect level of the ap pliance You did not remove the packaging and or the transit bolts The load is very small Adjust the level of the appliance Refer to Installation Remove the packaging and
3. All fabrics The maximum load of the laundry is related to the type of laundry All fabrics The maximum load of the laundry is related to the type of laundry Hand washed items Drainage of the water Spin phase at the maximum speed Drainage of the water Rinses Long spin SPIN REDUCTION SPIN REDUCTION RINSE HOLD EXTRA SPOELEN 12 Programme Type of load Cycle Functions Temperature max weight of load description Gordijnen Set this programme Prewash SPIN REDUCTION 40 Cold to wash curtains It Wash RINSE HOLD adds automatically Rinses EXTRA SPOELEN the prewash phase to Short spin clean the dust from the curtains Do not put the deter gent into the prewash compartment max 2 kg Jeans All items in jeans Jer Wash SPIN REDUCTION 60 Cold sey made items with Rinses RINSE HOLD hi tech materials Short spin EXTRA SPOELEN max 6 kg TIJD BESPAREN 20 min 3 kg Cotton and synthetic Wash SPIN REDUCTION 40 30 items with light soil or Rinses worn only one time Short spin Eco White and fast col Wash SPIN REDUCTION 60 40 oured cotton with Rinses RINSE HOLD normal soil Long spin EXTRA SPOELEN max 6 kg TIJD BESPAREN 1 if you press the button 6 two times Super Quick function set we recommend you to decrease the quantity of the load It is possible to keep the full load but the washing results are not good 2 The wash and spin phase is soft to prevent the creases of the
4. codes Refer to Troubleshooting chapter e Err The display shows this message for some seconds if You set a function that is not applicable for the programme You change the programme while it operates The indicator of the Start Pause button B flashes ced When the programme is completed Door lock B i You cannot open the appliance door when the symbol is on You can open the door only when the symbol goes off If the programme is completed but the symbol stays on e There is water in the drum e The Rinse Hold function is on a The child lock symbol The symbol comes on when you activate this device START PAUSE BUTTON Press button l to start or interrupt a programme DELAY START BUTTON Press button J to delay the start of a programme from 30 minutes to 20 hours TIME SAVE BUTTON E Press the button J to decrease the programme duration e Press one time to set Shortened du ration for items with daily soil e Press two times to set Extra Quick for items with almost no soil i Some programmes accept only one of the two functions EXTRA RINSE BUTTON Press button R to add rinsing phases to a programme Use this function for persons allergic to detergents and in areas where the wa ter is soft SPIN BUTTON El Press this button to e Decrease the maximum speed of the spin phase of the programme e Activate the Rinse Hold function Set
5. full of water put the drainage duct back again and empty the container Do steps 3 and 4 again and again until no more water flows out from the drain pump Pull back the drainage duct and turn the filter to remove it Remove fluff and objects from the pump Make sure that the impeller of the pump can turn If this does not oc cur contact the service centre 24 Clean the filter under the water tap and put it back in the pump into the special guides Make sure that you tighten correct ly the filter to prevent leakages Close the drain pump door THE INLET HOSE FILTER AND THE VALVE FILTER It could be necessary to clean the filters when The appliance does not fill with wa ter The appliance fills with the water for along time The indicator of button l flashes and the display shows the related alarm Refer to Troubleshooting WARNING Disconnect the mains plug from the mains socket To clean the water inlet filters Close the water tap Remove the water inlet hose from the water tap Clean the filter in the inlet hose with a stiff brush Remove the inlet hose behind the appliance Clean the filter in the valve with a stiff brush or a towel ENGLISH 25 Install again the inlet hose Make sure that the couplings are tight to prevent leakages Open the water tap EMERGENCY DRAIN Because of a malfunction the appl
6. ANCE 1 2 Disconnect the mains plug from the mains socket Cut off the mains cable and discard it Discard the door catch This pre vents children or pets to be closed in the appliance There is a risk of suffocation only for front loading appliances w ENVIRONMENT CONCERNS PACKAGING MATERIALS Recycle the materials with the symbol LD Put the packaging in applicable con tainers to recycle it ECOLOGICAL HINTS To help the environment use less water and energy obey these instructions Set a programme without the pre wash phase to wash laundry with nor mal soil e Always start a washing programme with the maximum load of laundry e If necessary use a stain remover when you set a programme with a low temperature e To use the correct quantity of the de tergent check the water hardness of your domestic system TECHNICAL INFORMATION The symbol on the product or on its packaging indicates that this product may not be treated as household waste Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local council your househo
7. L 60460 FL WASHING MACHINE USER MANUAL L 60468 FL L 60660 FL 2 CONTENTS SAFETY INFORMATION ENVIRONMENT CONCERNS TECHNICAL INFORMATION PRODUCT DESCRIPTION ACCESSORIES CONTROL PANEL PROGRAMMES BEFORE FIRST USE USING THE APPLIANCE LOADING THE LAUNDRY FILLING THE DETERGENT AND ADDITIVES SETTING AND STARTING A PROGRAMME AT THE END OF THE PROGRAMME HINTS AND TIPS CARE AND CLEANING TROUBLESHOOTING INSTALLATION ONA OPH HP O NNO CO F NNN on SERVICE When contacting Service ensure that you have the following data available The information can be found on the rating plate Model PNC Serial Number The following symbols are used in this user manual A Warning Important Safety information i General information and tips g Environmental information Subject to change without notice ENGLISH 3 FOR PERFECT RESULTS Thank you for choosing this AEG product We have created it to give you impeccable performance for many years with innovative technologies that help make life simpler features you might not find on ordinary appliances Please spend a few minutes reading to get the very best from it ACCESSORIES AND CONSUMABLES In the AEG webshop you ll find everything you need to keep all your AEG appliances looking spotless and working perfectly Along with a wide range of accessories designed and built to the high quality standards you would expect from specialist coo
8. TAINS For some stains water and detergent is not sufficient We recommend that you remove these stains before you put the items in the appliance Special stain removers are available Use the special stain remover that is ap plicable to the type of stain and fabric ENGLISH 19 DETERGENTS AND ADDITIVES e Only use detergents and additives specially made for washing machines e Do not mix different types of deter gents e To help the environment do not use more than the correct quantity of de tergent e Obey the instructions that you find on the on packaging of these prod ucts Use the correct products for the type and colour of the fabric the pro gramme temperature and the level of soil e If you use liquid detergents do not set the prewash phase e If your appliance has not the deter gent dispenser with the flap device add the liquid detergents with a dos ing ball WATER HARDNESS If the water hardness in your area is high or moderate we recommend that you use a water softener for washing machines In areas where the water hardness is soft it is not necessary to use a water softener To know the water hardness in your area contact your local water authority Obey the instructions that you find on the packaging of the products Equivalent scales measure the water hardness e German degrees dH e French degrees TH e mmol l millimol for each litre inter national unit for the ha
9. The indicator of the Start Pause but ton M goes off e The door lock symbol goes off Press button M to deactivate the ap pliance After five minutes from the end of the programme the energy saving function automatically deacti vates the appliance ENGLISH 17 3 Press button The programme starts OPEN THE DOOR While a programme or the delay start operates the appliance door is locked To open the appliance door 1 Press button The door lock symbol in the display goes off 2 Open the appliance door 3 Close the appliance door and press button JZ The programme or the delay start continues If the temperature and level of the water in the drum are too high the door lock symbol stays on and you cannot open the door To open the door do the steps that follow 1 Deactivate the appliance 2 Wait for some minutes 3 Make sure that no water is in the drum i If you deactivate the appliance it is necessary to set the pro gramme again When you activate the appli ance again the display show the end of the last set programme Turn the programme knob to set a new cycle e Remove the laundry from the appli ance Make sure that the drum is empty Keep the door ajar to prevent mil dew and odours Close the water tap The washing programme is completed but there is water in the drum The drum turns regularly to prevent the creases in the laundry 18 The
10. door stays locked 3 When the programme is comple You must drain the water to open the ted and the door lock symbol goes door off you can open the door Tocdrainthe water 4 Deactivate the appliance 1 lf necessary decrease the spin i The appliance drain and spin speed automatically after approximate 2 Press the Start Pause button l ly 18 hours The appliance drain the water and spin HINTS AND TIPS THE LAUNDRY LOAD e Divide the laundry in white col oured synthetics delicates and wool e Obey the washing instructions that are on the laundry care labels e Do not wash together white and col oured items e Some coloured items can discolour with the first wash We recommend that you wash them separately for the first times e Button up pillowcases close zippers hooks and poppers Tie up belts Empty the pockets and unfold the items e Turn inside out multilayered fabrics wool and items with painted illustra tions e Remove hard stains e Wash with a special detergent heavy soil stains Be careful with the curtains Remove the hooks or put the curtains in a washing bag or pillowcase e Do not wash in the appliance Laundry without hems or with cuts Underwired bras Use a washing bag to wash small items e A very small load can cause balance problems with the spin phase If this occurs adjust manually the items in the tub and start the spin phase again STUBBORN S
11. drain hose makes a loop to prevent that remain ing particles go in the appliance from the sink Directly to a built in drain pipe in the room wall and tighten it with a clip i You can extend the drain hose to maximum 400 cm Contact the service centre for the other drain hose and the extension ENGLISH 35 www aeg com shop 132933220 A 212011 C
12. e not to dam age the hoses Remove the polystyrene protection from the bottom Pull up the appliance in vertical po sition Remove the power supply cable and the drain hose from the hose holders Remove the three bolts Use the key supplied with the appliance Pull out the plastic spacers ENGLISH 31 12 Replace the plastic spacers with the plastic caps You can find these caps in the user manual bag i We recommend that you keep the packaging and the transit bolts for when you move the appliance If the appliance is delivered in the winter months when there are minus temperatures Store it at room temperature for 24 hours before using for the first time POSITIONING AND LEVELLING Install the appliance on a flat hard floor e Make sure that carpets do not stop the air circulation below the appli ance Make sure that the appliance does not touch the wall or other units e Loosen or tighten the feet to adjust the level A correct adjustment of the appliance level prevents the vibra tion noise and the movement of the appliance when in operation 32 e The appliance must be level and sta ble A CAUTION Do not put cardboard wood or equivalent materials below the appliance feet to adjust the lev el THE INLET HOSE Connect the hose to the appliance Turn the inlet hose only left or right
13. iance cannot drain the water If this occurs do steps 1 through 6 of To clean the drain pump If necessary clean the pump Put the drainage duct back and close the drain pump flap When you drain the water with the emergency drain procedure you must activate again the drain system 1 Put 2 litres of water in the main wash compartment of the deter gent dispenser 2 Start the programme to drain the water FROST PRECAUTIONS If the appliance is installed in an area where the temperature can be less than 0 C remove the remaining water from the inlet hose and the drain pump 1 Disconnect the mains plug from the mains socket 2 Close the water tap 3 Remove the water inlet hose 4 Put the two ends of the inlet hose in a container and let the water flow out of the hose 5 Empty the drain pump Refer to the emergency drain procedure 6 When the drain pump is empty in stall the inlet hose again WARNING Make sure that the temperature is more than 0 C before you use the appliance again The manufacturer is not respon sible for damages caused by low temperatures 26 TROUBLESHOOTING The start of the appliance does not oc F LI The appliance does not drain cur or it stops during operation the water First try to find a solution to the prob lem refer to the table If not contact the service centre With some problems the acoustic signals operate and the display shows an a
14. jnen e Synthetica 40 800 Spoelen e Strijkvrij 30 400 r g a Pompen fine S olo c PO nide Z Extra Tijd Cenkugeren Melee Temp C TPM _ Spoclen Besparen Startuitstel Stori Pouze Aan Uit F LI FI JT ie D L FE On Off button Aan Uit A Programme knob Display E Start Pause button Start Pauze EB Delay start button Startuitstel B Time saving button Tijd Besparen Extra rinse button Extra Spoelen E Spin button TPM E Temperature button Temp C ON OFF BUTTON Press this button to activate or deacti vate the appliance A tune sounds when the appliance is activated DISPLAY The AUTO Stand by function automati cally deactivates the appliance to de crease the energy consumption when e You do not use the appliance for 5 minutes before you press button All settings are cancelled Press button fi to activate the ap pliance again Set again the washing programme and all possible options e After 5 minutes from the end of the washing programme Refer to At the end of programme PROGRAMME KNOB Turn this knob to set a programme The display shows A The programme time ENGLISH 9 When the programme starts the time decreases with steps of 1 minute e The delay start When you press the delay start button the display shows the delay start time e Alarm codes If the appliance has a malfunction the display shows alarm
15. ks of structural damage or injury e Do not install or use the appliance where the temperature is less than 0 AG e When you install the appliance on a carpet floor make sure that there is air circulation between the appliance and the carpet Adjust the feet to have the necessary space between the appliance and the carpet Water connection e Do not connect the appliance with old hoses already used Only use new hoses e Make sure not to cause damage to the water hoses e Do not connect the appliance to new pipes or pipes not used for a long time Let the water flow for some mi nutes then connect the inlet hose e The first time you use the appliance make sure that the water hoses and the couplings do not have leakages Electrical connection e Make sure that the appliance is earthed e Make sure that the electrical informa tion on the rating plate agrees with the power supply Always use a correctly installed shockproof socket ENGLISH 5 Do not use multiple plugs and exten sion cables There is a risk of fire Do not replace or change the mains cable Contact the service centre Make sure not to cause damage to the mains plug and cable Connect the mains plug to the mains socket only at the end of the installa tion Make sure that there is access to the mains plug after the installa tion Do not pull the mains cable to dis connect the appliance Always pull the mains plug DISCARD THE APPLI
16. kware to cutlery baskets from bottle holders to delicate laundry bags sa Visit the webshop at www aeg com shop VISIT OUR WEBSITE FOR Products Brochures User manuals Trouble shooter Service information www aeg com SAFETY INFORMATION Before the installation and use read this manual carefully e For your safety and the safety of your property e To help the environment e For the correct operation of the ap pliance Always keep these instructions with the appliance also if you move or give it to a different person The manufacturer is not responsible if an incorrect installation and use causes damage CHILDREN AND VULNERABLE PERSON SAFETY e Do not let persons children inclu ded with reduced physical sensory reduced mental functions or lack of experience and knowledge use the appliance They must have supervi sion or instruction for the operation of the appliance by a person who is responsible for their safety e Keep all packaging away from chil dren There is the risk of suffocation or injury Keep all detergents away from chil dren e Keep children and pets away from the appliance when the door is open Before you close the appliance door make sure that children and pets are not into the drum e If the appliance has a child safety de vice we recommend to activate it GENERAL SAFETY e Do not use the appliance for profes sional use The app
17. larm code e FIG The appliance does not fill e FUN The appliance door is open or not closed correctly WARNING Deactivate the appliance before you do the checks with water Problem Possible cause Possible solution The appliance The water tap is closed Open the water tap does not fill with water The water inlet hose is Make sure that the water inlet damaged hose has no damages The filters in the water in Clean the filters Refer to Care let hose is blocked and cleaning The water tap is blocked Clean the water tap or is furred with lime scale The connection of the Make sure that the connection is water inlet hose is not correct correct The water pressure is too Contact your local water authori low ty The appliance The water drain hose is Make sure that the water drain does not drain the damaged hose has no damages water The filter of the drain pump is blocked Clean the filter of the drain pump Refer to Care and clean ing The connection of the water drain hose is not correct Make sure that the connection is correct A washing programme without the drain phase is set The function Rinse amp Hold is on The appliance door is open or not closed correct ly Set the drain programme Set the drain programme Close the door correctly Problem Possible cause ENGLISH 27 Possible solution The spin phase does not operate
18. laundry The appliance adds some rinses 3 The default phase of the spin speed is related to cotton items Set the spin speed Make sure that it agrees with the laundry 4 Set this programme to have a good washing results and decrease the energy consumption The time of the washing programme is extended For cotton economy programmes you can set only the Extra Quick duration CONSUMPTION VALUES Programme Energy consumption Water consump KWh 2 tion litre White Cottons 95 C 2 2 62 Cottons 60 C 12 58 Cottons 40 C 0 75 58 Synthetics 40 C 0 5 43 Delicates 40 C 0 53 50 Wool Handwash 30 C 0 25 45 1 Refer to the display for the programme time ENGLISH 13 2 The consumption information shown in this chart is indicative It can vary depending on the quantity and the type of laundry on the temperature of the water supply and on the ambient temperature Standard programmes for the Energy Label consumption values The cotton 60 C economy and cotton 40 C economy are the standard cotton programmes for normally soiled cotton laundry They are suitable to clean nor mally soiled cotton laundry and they are the most efficient programmes in terms of combined energy and water consumption for washing that type of cotton laundry They agree with EN60456 i The actual water temperature may differ from the declared cy cle temperature 14 BEFORE FIRST USE 1 To activate the drain system p
19. ld waste disposal service or the shop where you purchased the product Dimensions Width Height Depth 600 850 522 mm Total depth 540 mm Electrical connection Voltage 230 V Overall power 2200 W Fuse 10A Frequency 50 Hz Level of protection against ingress of solid particles IPX4 and moisture ensured by the protective cover except where the low voltage equipment has no protection against moisture Water supply pressure Minimum 0 5 bar 0 05 MPa Maximum 8 bar 0 8 MPa Water supply 1 Cold water Maximum load Cotton 6 kg Spin speed Maximum 1400 rpm L 60460 FL 1400 rpm L 60468 FL 1600 rpm L 60660 FL 1 Connect the water inlet hose to a water tap with a 3 4 thread PRODUCT DESCRIPTION Ft Worktop A Detergent dispenser Control panel E Door handle B Rating plate 6 Drain pump ACCESSORIES ENGLISH Feet for the appliance level El Water drain hose El Water inlet valve Mains cable Transit bolts Feet for the appliance level 7 Spanner To remove the transit bolts A Plastic caps To close the holes on the rear side of the cabinet after the removal of the transit bolts Anti flood inlet hose To prevent possible leakage 4 Plastic hose guide To connect the drain hose on the edge of a sink 8 CONTROL PANEL Stop Eco R Katoen 20 Min 3 kg e Voorwas Jeans e Vlekken a R Gordi
20. liance is only for domestic use e Do not change the specifications of this appliance There is the risk of in jury and damage to the appliance e Do not put flammable products or items that are wet with flammable products in near or on the appliance Risk of explosion or fire e Obey the safety instructions on the detergent packaging to prevent burns to eyes mouth and throat e Make sure that you remove all metal objects from the laundry Hard and sharp material can cause damage to the appliance e Do not touch the glass of the door while a programme operates The glass can be hot only for front load ing appliances CARE AND CLEANING e Deactivate the appliance and discon nect the mains plug from the mains socket e Do not use the appliance without the filters Make sure that the installation of the filters is correct An incorrect installation causes water leakages INSTALLATION e The appliance is heavy be careful when you move it e Do not transport your appliance with out the transit bolts you can damage internal components and cause leak ages or malfunctions e Do not install and connect a dam aged appliance e Make sure to remove all packaging and transport bolts e Make sure that the mains plug is dis connected from the mains socket during installation e Only a qualified person must do the electrical installation the plumbing and the installation of the appliance This to prevent the ris
21. nditioner starch Put the product in the compartment before you start the pro gramme This is the maximum level for the quantity of liquid additives AIX Flap for powder or liquid detergent Turn it up or down in the correct position to use powder or liquid detergent i Always obey the instructions that you find on the packaging of the deter gent products Check the position of the flap 1 Pull out the detergent dispenser until it stops 2 Press the lever down to remove the dispenser 16 a Measure out the detergent and the fabric conditioner Carefully close the detergent dis penser Make sure that the flap does not cause a blockage when you close the drawer 3 4 To use powder detergent turn the flap up To use liquid detergent turn the flap down With the flap in the position DOWN Do not use gelatinous or thick iquid detergents Do not put more liquid deter gent than the limit showed in the flap Do not set the prewash phase Do not set the delay start function SETTING AND STARTING A PROGRAMME INTERRUPT A PROGRAMME Turn the programme knob The indicator of button i flashes with red colour The indicators of the default tem perature and spin speed come on To change the temperature and or the spin speed press the related buttons Set the available functions and the delay start When you press the
22. or the transit bolts Refer to Instal lation Add more laundry in the drum The appliance fills with water and drain immediately The end of the drain hose is too low Make sure that the drain hose is in the correct position The washing re sults are not satis factory The detergent you used was not sufficient or cor rect Increase the detergent quantity or use a different one 28 Problem Possible cause Possible solution You did not remove the Use special products to remove stubborn stains before the stubborn stains you wash the laundry Incorrect temperature Make sure that you set the cor was set rect temperature Too much laundry load Decrease the laundry load After the check activate the appliance If the display shows other alarm codes The programme continues from the contact the service centre point of interruption If the problem occurs again contact the service centre INSTALLATION UNPACKING ENGLISH 29 Use the gloves Remove the exter nal film If necessary use a cutter Remove the cardboard top Remove the polystyrene packaging materials Remove the internal film Open the door and remove all the items from the drum 30 10 11 Put the front piece on the floor be hind the appliance Carefully put down the appliance with the rear side on it Make sur
23. rdness of wa ter e Clarke degrees 20 Water hardness table Water hardness Rel Type dH T H mmol l Clarke 1 soft 0 7 0 15 0 1 5 0 9 2 medium 8 14 16 25 1 6 2 5 10 16 3 hard 15 21 26 37 2 6 3 7 17 25 4 very hard gt 2 S 53 gt 25 CARE AND CLEANING A WARNING Disconnect the appliance from the mains supply before you clean it DESCALING The water we use contains limescale If it becomes necessary use a water soft ener to remove limescales Use a special product made for wash ing machines Obey the instructions that you find on the packaging of the manufacturer Do this separately from the laundry wash EXTERNAL CLEANING Clean the appliance only with soap and warm water Fully dry all the surfaces ENGLISH 21 CAUTION Do not use alcohol solvents or chemical products MAINTENANCE WASH With the low temperature programmes it is possible that some detergent stays in the drum Make regularly a mainte nance wash To do this e Empty the laundry from the drum e Set the hottest cotton wash pro gramme Use a correct quantity of powder de tergent with biological properties After each wash keep the door open for a while to prevent mould and to let unpleasant smells go out DOOR SEAL Regularly examine the seal and remove WS all objects from the inner part v DRUM e Clean the drum with special product Regularly examine the drum to prevent limescale and
24. rel evant button the indicator of the set function comes on or the dis play shows the related symbol Press button Z to start the pro gramme The indicator of button is on with red colour 1 2 Press button The indicator flashes Press button J again The wash ing programme continues CANCEL A PROGRAMME 1 2 Turn the programme knob to Stop to cancel the programme Turn again the programme knob to a new washing programme At this time you can also set the available functions i The appliance does not drain the water CHANGE A FUNCTION You can change only some functions before they operate 1 Press button l The indicator flashes 2 Change the function set SET THE DELAY START 1 Press button J again and again until the display shows the number of minutes or hours 2 Press button l the appliance starts the countdown of the delay start When the countdown is comple ted the programme starts auto matically Before you press button fj to start the appliance you can can cel or change the set of the de lay start You cannot set the delay start with the Steam programme CANCEL THE DELAY START 1 Press button The related indi cator flashes 2 Press button Bl again and again until the display shows 0 AT THE END OF THE PROGRAMME G e The appliance stops automatically e The acoustic signals operate Inthe display comes on e
25. rust particles Only use special products to remove rust particles from the drum To do this for stainless steel e Start a short programme for cotton at the maximum temperature with a small quantity of detergent 22 DETERGENT DISPENSER To clean the dispenser Press the lever 2 Pull the dispenser out Remove the top part of the liquid additive compartment Clean all the parts with water Clean the dispenser recess with a brush Put back the dispenser in the re cess DRAIN PUMP Regularly examine the drain pump and make sure thatit is clean Clean the pump if The appliance does not drain the wa ter The drum cannot turn The appliance makes an unusual noise because of the blockage of the drain pump The display shows an alarm code be cause of the problem with water drain WARNING 1 Disconnect the mains plug from the mains socket 2 Do not remove the filter while the appliance oper ates Do not clean the drain pump if the water in the ap pliance is hot The water must be cold before you clean the drain pump ENGLISH 23 To clean the drain pump _ Open the drain pump door Put a container below the recess of the drain pump to collect the water that flows out Press the two levers and pull for ward the drainage duct to let the water flow out When the container is
26. this function to prevent fabric creases The appliance does not drain the water when the programme is completed Rinse Hold function is E 10 TEMPERATURE BUTTON Press button J to change the default temperature cold water ACOUSTIC SIGNALS FUNCTION You can hear the acoustic signals when e You activate the appliance e You deactivate the appliance e You press the buttons e The programme is completed e The appliance has a malfunction To deactivate activate the acoustic signals press button and button at the same time for 6 seconds i If you deactivate the acoustic signals they continue operate only when you press the buttons and when a malfunction occurs CHILD LOCK FUNCTION This function prevents children to play with the control panel e To activate the function press button Bl and button ij at the same time until the display shows the symbol FA e To deactivate the function press but ton and button J at the same time until the symbol goes off You can activate the function e Before you press the Start Pause but ton the appliance cannot start After you press the Start Pause but ton l all the buttons and the pro gramme knob are deactivated PERMANENT EXTRA RINSE FUNCTION With this function you can keep the ex tra rinse function permanently on when you set a new programme e To activate the function press button and button J at the same time un
27. til the indicator of button is on e To deactivate the function press but ton Bl and button at the same time until the indicator of button is off PROGRAMMES ENGLISH 11 Programme Type of load Cycle Functions Temperature max weight of load description Katoen White and coloured Wash SPIN REDUCTION 95 Cold cotton with normal Rinses RINSE HOLD soil Long spin EXTRA SPOELEN max 6 kg TIJD BESPAREN Katoen Voor White and coloured Prewash SPIN REDUCTION was cotton with heavy soil Wash RINSE HOLD 95 Cold max 6 kg Rinses EXTRA SPOELEN Long spin TIJD BESPAREN Katoen Vlekk max 6 kg Wash SPIN REDUCTION en Rinses RINSE HOLD 95 40 Long spin EXTRA SPOELEN TIJD BESPAREN Synthetica Synthetic or mixed Wash SPIN REDUCTION 60 Cold fabric items with nor Rinses RINSE HOLD mal level of soil Short spin EXTRA SPOELEN max 3 kg TIJD BESPAREN Strijkvrij Synthetic fabric items Wash SPIN REDUCTION 60 Cold with normal soil Rinses RINSE HOLD max 3 kg Short spin EXTRA SPOELEN TIJD BESPAREN Fijne Was Delicate fabrics as Wash SPIN REDUCTION 40 Cold acrylics viscose poly Rinses RINSE HOLD ester items with nor Short spin EXTRA SPOELEN mal soil TIJD BESPAREN max 3 kg jl Machine washable Wash SPIN REDUCTION Wol Zijce wool Hand washable Rinses RINSE HOLD Ce wool and delicate Short spin fabrics with hand washing care sym bol max 2 kg Centrifugeren Pompen Spoelen
28. ut 2 litre of water in the main wash com partment of the detergent dispens er Put a small quantity of detergent in the main wash compartment of the USING THE APPLIANCE 4 Open the water tap Connect the mains plug to the mains socket Press button MM to activate the ap pliance Put the laundry in the appliance LOADING THE LAUNDRY 1 2 Open the appliance door Put the laundry in the drum one item at a time Shake the items be fore you put them in the appliance detergent dispenser Set and start a programme for cotton at the highest temperature without laun dry This removes all possible dirt from the drum and the tub 5 Use the correct quantity of deter gent and additives 6 Set and start the correct pro gramme for the type of laundry and soil Make sure not to put too much laundry in the drum 3 Close the door Make sure that no laundry stays be tween the seal and the door There is a risk of water leakage or damage to the laundry ENGLISH 15 FILLING THE DETERGENT AND ADDITIVES E MAX The detergent compartment for the prewash phase the soak pro gramme and for the stain function Add the detergent for prewash soak and stain remover before the start of the programme The detergent compartment for the washing phase If you use a liquid detergent put it immediately before you start the programme Liquid additives compartment fabric co
Download Pdf Manuals
Related Search