Lenovo E50 Series - datorfixarna.com
Contents
1. 2 Confirm that the CD DVD has been properly placed in the drive If not reload the CD or DVD Otherwise continue with the next step of this procedure 3 Check the specifications that came with your computer to confirm that this optical drive is capable of reading this type of CD or DVD 4 If the CD DVD cannot be read replace it with a known good CD DVD such as one that was shipped with the computer 5 If the known good CD cannot be read visually check the operating side of the CD DVD for defects 16 User Guide Problem The capacity of the hard disk as indicated by the system is less than the nominal capacity Troubleshooting and problem resolution For computers equipped with the OneKey Recovery feature the system recovery feature needs to occupy some hard disk space This may account for the apparent hard disk capacity deficit Further Technical Explanation The nominal capacity of the hard disk is expressed in the decimal system 1000 bytes But the actual hard disk capacity is expressed in the binary system as 1024 bytes For example the nominal capacity 1G is 1000M while the actual capacity 1G is 1024M The capacity of the hard disk shown in Windows can be calculated according to the calculations in the following example The nominal capacity of the hard disk is 40G while its actual capacity should be 40 x 1000 x 1000 x 1000 1024 x 1024 x 1024 37G If the Service partition of 3G 3 x 1000 x 1000 x 1000 10242. 8 Using the Rescue System cccccsssssseeeeeseeeenseeeees 9 21 Onekey ROcOV Visado ini REENEN 10 2 2 Driver and Application Installation cccceeecceeeseeeeeeneeeees 10 233 Oystom Sel util tatiana did 11 E Nee EE 12 2 5 SYSTEM RECOVENY ici ENEE Eeer 12 2 6 Create Recovery Dier 12 Troubleshooting and Confirming Setup 13 3 1 Troubleshooting Display Problems 14 3 2 Troubleshooting Audio Problems AAA 15 3 3 Troubleshooting Software Probleme 15 3 4 Troubleshooting Problems with Optical Drives and Hard RI 16 3 5 Special considerations for troubleshooting Windows 17 3 6 Performing Daily Maintenance Toske AA 18 Contents 1 Chapter 4 Hardware Replacement Guide 19 Meel 23 4 2 Replacing MW 25 Appendix A 33 RE 33 Trademarks euer AL Ae a BAe 34 Energy star E 34 Enabling ErP compliance mode tas 35 Electronic emissions notices o sossos o neoon 36 Mexico regulatory notice sssss osso ossos noso nono 37 2 Contents Chapter Using the Computer Hardware 9 W Y This chapter contains the following o E o topics O gt Introduction to the computer hardware gt Information on computer connections gt O Note The descriptions in this chapter 9 might be different from what you see on your computer de
3. Lenovo Rescue System opens 8 User Guide Chapter Using the Rescue System 0 i o This chapter contains the following 9 S i o topics O gt OneKey Recovery O gt Driver and Application Installation Y gt System Setup Y gt System Backup gt gt System Recovery 9 gt Create Recovery Disc O A AE IS S ention Using this program will result in gt loss of data i sg Youcan restore the C drive of the computer i to factory default settings or to the last O system backup status using OneKey O Recovery If you do this all of the existing O data on drive C will be lost but the content 9 and format of the other partitions of the hard disk drive will remain unchanged O e If you want to install an operating system 0 and back it up with OneKey Recovery you 9 must format the C partition in NTFS format O and install the operating system on the C O partition Otherwise the OneKey Recovery O system cannot run UserGuide 9 SS SS SUS O A RR ROS RSS SS O O A A RSS RS SS SS ES O DS O SS Ed L Note about the service partition The files and relevant data used by the rescue system are saved in the service partition Deleting this partition will make the rescue system unusable For more detailed information see the following ins
4. Refer to Removing the computer cover Remove the front bezel Refer to Removing and replacing the front bezel Disconnect the data and power cables from the rear of the optical drive Remove the two screws that secure the optical drive to drive bay a E won Push the optical drive straight out of the front of the chassis 6 Slide the new optical drive into the bay from the back until it snaps into position 7 Secure the optical drive to the bay with the two screws 8 Connect the data and power cables to the drive 9 Install the front bezel Refer to Removing and replacing the front bezel 10 Refer to Completing the installation 30 User Guide 4 2 6 Completing the installation After replacing a part or parts you must close the computer cover and reconnect all the cables including telephone lines and power cords Some parts will require confirming updated information in the Setup Utility program Refer to Starting the Setup Utility in the Hardware Maintenance Manual To complete the installation 1 Ensure that all components have been reassembled correctly and that no tools or loose screws are left inside your computer Refer to Locating components for the location of the various components 2 Make sure that the cables are routed correctly before replacing the computer cover 3 Position the computer cover on the chassis so that the rail guides on the bottom of the computer cover engag
5. e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult an authorized dealer or service representative for help Lenovo is not responsible for any radio or television interference caused by using other than recommended cables or connectors or by unauthorized changes or modifications to this equipment Unauthorized changes or modifications could void the user s authority to operate the equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Responsible party Lenovo United States Incorporated 1009 Think Place Building One Morrisville NC 27560 U S A Telephone 919 294 5900 FE 36 User Guide Mexico regulatory notice Advertencia En Mexico la operaci n de este equipo est sujeta a las siguientes dos condiciones 1 es posible que este equipo o dispositivo no cause interferencia perjudicial y 2 este equipo o dispositivo debe aceptar cualquier interferencia incluyendo la que pueda causar su operaci n no deseada User Guide 37 38 User Guide
6. x 1024 x 1024 2 79G is subtracted the capacity of the hard disk shown in the system can be obtained The capacity of the hard disk as calculated using this method may be slightly different from the actual capacity due to the rounding of totals 3 5 Special considerations for troubleshooting Windows Record the following information as it may be useful later when troubleshooting system problems 1 The serial number of the software The serial number was shipped with the computer and provided separately by the manufacturer The Help Center is unable to retrieve this number 2 The drivers for this computer model only support the Windows 7 system 3 When you use the Windows Media Center to watch TV be particularly attentive to the following e Inthe following two situations you must re save a channel list a When you change your TV signal from digital to analog your saved channel list for digital TV is deleted When you want to watch digital TV again you must create and save a new channel list b When you change your TV signal from analog to digital your saved channel list for analog TV is deleted When you want to watch analog TV again you must create and save a new channel list User Guide 17 e You must set the TV tuner input signal to analog before you can watch Teletext programming 3 6 Performing Daily Maintenance Tasks Cleaning the computer components Because many of the computer components consist of sophisticat
7. Driver and Application Installation function in the rescue system provides a way for the user to conveniently reinstall all of the Lenovo applications and drivers that were shipped with your Lenovo hardware 10 User Guide Method 1 Automatic Installation Repeatedly press and release the F2 key once turning on the computer until the Lenovo Rescue System open then select Driver and Application Installation Follow the on screen prompts to install the Lenovo drivers and applications Click Install to start installing the Lenovo Driver and Application Installation software The system will restart After the system has restarted the installation process will continue until it has completed Method 2 Manual Installation In the Windows system Click Start All Programs Lenovo Lenovo Driver and Application Installation After starting the procedure install all the drivers and software manually by following the prompts O Notes 1 Do not install software which is already installed on the computer 2 Make sure that the Driver and Application Installation software has been automatically installed before starting the operating system The manual installation function can only be used after the software has been installed 2 3 System Setup System Setup configures the network configuration for the Lenovo Rescue System to ensure your Rescue System can connect to internet In addition System Setup sets and manages all pass
8. Lenovo E50 Series User Guide Version 1 0 2014 06 SP40G46486 lenovo Important Safety Information Before using this manual it is important that you read and understand all of the related safety information for this product Refer to the Safety and Warranty Guide that you received with this product for the latest safety information Reading and understanding this safety information reduces the risk of personal injury or damage to your product Danger Be aware of extremely hazardous or lethal situations gt Attention Be aware of possible damage to programs devices or data Note Pay attention to this important information Copyright Lenovo 2014 All rights reserved LIMITED AND RESTRICTED RIGHTS NOTICE If data or software is delivered pursuant a General Services Administration GSA contract use reproduction or disclosure is subject to restrictions set forth in Contract No GS 35F 05925 Contents Important Safety Information Chapter 1 Chapter 2 Chapter 3 Using the Computer Hardware sss 1 1 1 Front view of the ChasSiS eretas 2 1 2 Rear view of the CNASSIS ovio ad aak 3 1 3 Basic connector metructonmg cnn 4 1 4 Connecting your Computer 5 1 5 Audio configuration metrOchon ei eseeesteeeenteeenteeereneeeeas 6 1 6 Connecting the power con 7 1 7 Display connecting instructions when playing Blu ray Discs 8 1 8 Wired keyboard selected models on
9. amp Padlock loop Power connector Cable clip PCI Express X 16 graphics card slot PCI Express X 1 card slot User Guide 3 O Note If your model has two VGA monitor connectors be sure to use the connector on the graphics adapter AN Attention Do not open the WiFi antenna cover 1 3 Basic connector instructions O Note Your computer may not have all of the connectors described in this section Connector Description Microphone Use this connector to attach a microphone to your computer when you want to record sound or if you use speech recognition software Headphone Use this connector to attach headphones to your computer when you want to listen to music or other sounds without disturbing anyone Audio line in connector Used to receive audio signals from an external audio device such as a stereo system When you attach an external audio device a cable is connected between the audio line out connector of the device and the audio line in connector of the computer Audio line out connector Used to send audio signals from the computer to external devices such as powered stereo speakers speakers with built in amplifiers headphones multimedia keyboards or the audio line in connector on a stereo system or other external recording device Memory card reader Use to view and share digital photos music and videos stored on a media card Power connector Connect to the power cable The appeara
10. clean and free of grease stains 18 User Guide Chapter Hardware Replacement Guide 9 9 Y This chapter contains the following topics vi gt Locating components E gt Identifying parts on the system board o gt Removing the computer cover V gt Removing and replacing the front bezel O gt Replacing a memory module i o gt Replacing the hard disk drive Y gt Replacing an optical drive gt Completing the installation User Guide 19 O O O O A RR RS RSS SS O A A RS SS SS SS SS A O SS Bd L Overview This guide is intended to be used by customers who are replacing Customer Replaceable Units CRUs as well as trained service personnel who are replacing Field Replaceable Units FRUs In this guide CRUs and FRUs will be referred to as paris Note Trained service personnel should refer to the Hardware Maintenance Manual HMM for parts ordering information This guide does not include procedures for all parts It is expected that cables switches and certain mechanical parts can be replaced by trained service personnel without the need for step by step procedures O Note Use only parts provided by Lenovo M The description of the TV card in this manual applies only to machines which have a TV card It does not apply to machines which do no
11. d press Enter 8 Select Enabled and press Enter Press F10 to save changes and exit the Setup Utility program Press Enter when prompted to confirm Note When ErP compliance mode is enabled you only can wake up your computer by pressing the power switch Additional information as required by EU Regulation 617 2013 implementing Directive 2009 125 EC with regard to ecodesign requirements for computers and computer servers can be found here www lenovo com ecodeclaration User Guide 35 Electronic emissions notices The following information refers to Lenovo machine type e 90BX Federal Communications Commission FCC Declaration of Conformity This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates used and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures
12. de 1 6 Connecting the power cord Connect the power cord to an electrical outlet We recommend using a grounded connection or a surge protector Some models are equipped with Power Adapter User Guide 7 1 7 Display connecting instructions when playing Blu ray Discs O Note Only some models are equipped with Blu ray optical drive Check the connectors available on your computer and display and select an appropriate cable according to the table below Other types of cables do not meet the requirements of the Blu ray standard You need to purchase the cable separately if the computer is not equipped with the corresponding cable This table will help you to identify the connectors on your computer and display Connection Type Computer Cable Display d 5 hb DVI to DVI all TE DVI cable a Sib DVI to HDMI z H E Cree DVI HDMI cable pu ess HDMI to HDMI in CR E HDMI cable gt HDMI to DVI Ham JE BIR Bl HDMI DVI cable Cone J E 1 8 Wired keyboard selected models only F2 Your computer has the Lenovo Rescue System installed To learn more about this program repeatedly press and release the F2 key once turning on the computer until the
13. e the rails Then push the computer cover closed until it snaps into position Screw back the two screws on the chassis AI e Z Z Z AU AI AIT bt AN User Guide 31 4 Reconnect the external cables and power cords to the computer Refer to Locating connectors on the front of the computer and Locating connectors on the rear of the computer Note In most areas of the world Lenovo requires the return of the defective CRU Information about this will come with the CRU or will come a few days after the CRU arrives 32 User Guide Appendix Declaration Thank you for using Lenovo products Carefully read all documents shipped with your computer before you install and use the product for the first time Lenovo is not responsible for any loss except when caused by installation and operations performed by Lenovo professional service personnel You are responsible if you fail to operate the product according to instructions and requirements in the manuals included with your computer or operate the product inappropriately This manual could include technical inaccuracies or typographical errors Changes are made periodically to the information herein these changes will be incorporated in new editions of the publication To provide better service Lenovo reserves the right to improve and or modify the products and software programs described in the manuals included with your computer and the co
14. ect the problem program then click the End Task button User Guide 15 Problem You need to install or uninstall a program Problem resolution During installation never abort the install process by powering the system off or through other drastic means This can cause system program disorder or even failure during system initialization During the uninstall process never directly delete the files or folders This is harmful to the system and might cause a system wide malfunction Use the following procedure to properly uninstall programs 1 Back up all documents and system settings related to the program before removing it If the program has its own uninstaller run it directly to uninstall the program If the program does not have its own uninstaller then select Control Panel from the Start menu From the Control Panel choose Programs and Functions Find the applicable program from the Programs and Functions dialog box and then select Uninstall Modify 6 Perform the instructions displayed to uninstall the software 3 4 Troubleshooting Problems with Optical Drives and Hard Disks Problem The Optical drive is unable to read a CD DVD Troubleshooting and problem resolution 1 Check to determine if there is an optical drive icon in the resource manager of the operating system If not restart your computer If there is still no icon contact Lenovo Service Otherwise continue with the next step of this procedure
15. ed integrated circuit boards it is very important to periodically clean the computer to prevent dust buildup The cleaning supplies you need to clean the components include a vacuum cleaner a soft cotton cloth clear water preferably purified or distilled water and cotton swabs A Attention Before you clean your computer disconnect the computer from the electrical outlet Clean your computer with a soft cloth dampened with water Do not use liquid or aerosol cleaners which may contain flammable substances O Note To avoid damaging the computer or display do not spray cleaning solution directly onto the display Only use products specifically designed for cleaning displays and follow the instructions included with the product The following are general methods for cleaning the components e You can use a soft cloth to remove dust on the surface of the computer the monitor the printer the speakers and the mouse e You can use a vacuum cleaner to clean in otherwise inaccessible corners e To clean the keyboard thoroughly shut down the computer and scrub it gently with a wet cloth Do not use the keyboard until it is dry Do not do any of the following e Allow water to enter the computer e Use a heavily dampened cloth e Spray water directly onto the surface of the monitor or inside the computer LCD monitors should be cleaned daily Use a dry cloth to brush dust from the monitor and keyboard every day Keep all surfaces
16. er and wait three to five minutes to let it To 1 cool down before removing the cover remove the computer cover Remove any media disks CDs or memory cards from the drives shut down the operating system and turn off the computer and all attached devices Unplug all power cords from electrical outlets Disconnect all cables attached to the computer This includes power cords input output I O cables and any other cables that are connected to the computer Refer to Locating connectors on the rear of the computer Remove the two screws that secure the computer cover at the rear of the chassis User Guide 25 5 Slide the computer cover to the rear of the chassis to remove it O Note For this procedure it helps to lay the computer on its side 26 User Guide 4 2 2 Removing and replacing the front bezel To remove and replace the front bezel 1 Remove the computer cover Refer to Removing the computer cover O Note For this procedure it helps to lay the computer on its side 2 Remove the front bezel by releasing the three plastic tabs inside the chassis and pushing the bezel outward as shown 3 To reinstall the bezel align the plastic tabs on the bottom of the bezel with the corresponding holes in the chassis then snap them into position at the bottom and top 4 Refer to Completing the installation User Guide 27 4 2 3 Replacing a
17. er cover refer to Removing the computer cover 4 1 1 Locating components The following illustration will help you to locate the various components in your computer MESS Y Y Microprocessor fan and heatsink Memory modules Optical drive Hard disk drive System fan User Guide 23 4 1 2 Identifying parts on the system board The system board sometimes called the motherboard is the main circuit board in your computer It provides basic computer functions and supports a variety of devices that are factory installed or that you can install later The following illustrations show the locations of parts on the system board Lenovo E50 00 E AAA E EEE eee BERBER GEE EEE E ap ir RE a a System fan header Microprocessor and heat sink El Microprocessor fan header Memory connector E Hard disk and optical disk drive E SATA connectors 2 power connector PCI express X 16 adapter slot El Battery 24 User Guide e Puy Ho Ao Hardware clear CMOS jumper LPC debug header Front panel connector Power fan header Front USB connectors 2 PCI express X 1 adapter slot Front audio connector 4 2 Replacing hardware Note Use only parts provided by Lenovo 4 2 1 Removing the computer cover A Attention Turn off the comput
18. ers UPS systems regulators fluorescent lamps or other computers that may be generating magnetic interference Move any interfering devices away from the computer If the problem persists contact Lenovo Service 3 2 Troubleshooting Audio Problems Problem No sound from the integrated speakers Troubleshooting and problem resolution Adjust the Windows volume control double click the speaker icon in the lower right corner of your screen Ensure that the volume is turned up and the sound is not muted Adjust the volume bass or treble controls to eliminate distortion Reinstall the audio driver Disconnect any headphones from the headphone connector sound from the speakers is automatically disabled when headphones are connected to the computer s side panel headphone connector Problem No sound from headphones Troubleshooting and problem resolution Check the headphone cable connection ensure that the headphone cable is securely inserted into the headphone connector Adjust the Windows volume control click or double click the speaker icon in the lower right corner of your screen Ensure that the volume is turned up and the sound is not muted 3 3 Troubleshooting Software Problems Problem You are unable exit a running program normally Troubleshooting and problem resolution 1 Open the Task Manager window by pressing Ctrl Alt and Delete at the same time Select the Application tab sel
19. he program s documentation O Note The procedures in this document were written for the Windows default view so they may not apply if you set your Lenovo computer to the Windows Classic view 3 1 Troubleshooting Display Problems Problem Blank screen or no image is displayed on the monitor Troubleshooting and problem resolution 1 2 Check to see if the monitor has been turned on if not press the Power button Check to see if the monitor power cord is loose if so plug the power cord securely into the monitor Check to see if the signal cable to the monitor is securely connected to the connector on the computer graphics card if not shut down the computer then connect the signal cable of the monitor securely to the connector on the computer graphics card Problem You need to change the display property settings Setting display background and icon properties 1 Right click the desktop anywhere except over an icon then select Personalize from the pop up menu From here select the appropriate options to e Change the desktop background e Select a screen saver e Select colors and appearance options for icons and text e Set resolution and colors in the Display Settings options 14 User Guide Problem Ripple on screen Troubleshooting and problem resolution 1 Check to see if any of the following devices are located less than one meter from the computer refrigerators electric fans electric dry
20. ically e If the voltage supply range is 100 127 V AC set the switch to 115 V e If the voltage supply range is 200 240 V AC set the switch to 230 V SS e QUES En N GE UA User Guide 5 1 5 Audio configuration instruction This instruction is only for PC models whose mainboard supports audio transforming from 2 0 stereo to 5 1 surround This model of computer supports transforming stereo sound into 5 1 surround sound Use the following guides when connecting to the 5 1 surround audio device Ed Surround Blue line in connector e Green line out connector Front channel Pink Mic in connector e ce O e O Center LFE The configurations are as follows 1 4 Right click the sound icon in system property bar and select the sounds option to setup the sounds in the pop up dialog box Select a playback device from the playback dialog box and then click the configure button to configure it Select 5 1 surround from audio channels in the pop up speaker setup dialog box to proceed with the speaker setup by following as prompted After the configuration 5 1 surround can be used O Note If the audio configuration interfaces in above differ from your actual computer you may use the above steps as reference to configure the 5 1 surround audio device in your actual audio configuration interface and read the electronic help information for further assistance User Gui
21. mate Visual Experience are trademarks of Advanced Micro Devices Inc Other company product or service names referred to herein or in other Lenovo publications may be trademarks or service marks of others All rights reserved Names or marks of certain companies mentioned in the manuals included with your computer or this document do not necessarily indicate that related software or hardware is included The actual configuration of the product depends on the packing list description Energy Star Statement ENERGY STAR ENERGY STARO is a joint program of the U S Environmental Protection Agency and the U S Department of Energy aimed at saving money and protecting the environment through energy efficient products and practices Lenovo is proud to offer our customers products with an ENERGY STAR compliant designation The following machine types have been designed and tested to conform to the ENERGY STAR program requirement for computers at the time of manufacture For more information about ENERGY STAR ratings for Lenovo computers go to http www lenovo com e 90BX By using ENERGY STAR compliant products and taking advantage of the power management features of your computer you reduce the consumption of electricity Reduced electrical consumption contributes to potential financial sayings a cleaner environment and the reduction of greenhouse gas emissions 34 User Guide For more information about ENERGY STAR go
22. memory module To replace a memory module 1 Remove the computer cover Refer to Removing the computer cover 2 Locate the memory module connectors Refer to Locating components 3 Remove the memory module being replaced by opening the retaining clips as shown 4 Insert the notched end E of the new memory module into the slot Press the memory module firmly and pivot the memory module until it snaps into place Make sure that the memory module is secured in the slot and does not move easily 5 Refer to Completing the installation 28 User Guide 4 2 4 Replacing the hard disk drive To replace the hard disk drive L Remove the computer cover Refer to Removing the computer cover O Note For this procedure it helps to lay the computer on its side 2 3 4 Disconnect the data and power cables from the hard disk drive Remove the four screws that secure the hard disk drive to drive bay EH Remove the hard disk drive by pulling it straight out of the drive bay Slide the new hard disk drive into the drive bay 6 Secure the new hard disk drive to the drive bay with the four screws Connect the power and data cables to the hard disk drive Refer to Identifying parts on the system board Refer to Completing the installation User Guide 29 4 2 5 Replacing an optical drive To replace an optical drive 1 Remove the computer cover
23. nce of this connector may vary USB connector Use this connector to attach a device that requires a USB connection Ethernet connector Use this connector to attach the computer to an Ethernet type local area network VGA connector Used to attach a VGA monitor or other devices that use a VGA monitor connector DVI connector Used to attach a DVI monitor or other devices that use a DVI monitor connector 4 User Guide Connector Description HDMI connector Connect to the HDMI connector on your display or TV optional TV Tuner connector Only supported on systems with an optional TV tuner optional card O Note If your computer is equipped with a wireless keyboard or mouse follow the installation instructions for those devices 1 4 Connecting your computer Use the following information when connecting your computer e Look for the small connector icons on the back of your computer Match the connectors to the icons e f your computer cables and connector panel have color coded connectors match the color of the cable end with the color of the connector O Note Your computer may not have all of the connectors described in this section 1 4 1 Check the position of the voltage selection switch on the rear of the computer Use a ballpoint pen to slide the switch if necessary O Note Some computers do not have a voltage switch These computers control voltage automat
24. ntent of the manual at any time without additional notice The manuals included with your computer are provided to help you use Lenovo s products appropriately For the configuration of the product refer to the related contract if any or product packing list or consult the distributor for the product sales The content of the manuals included with your computer is protected by copyright laws and rules None of the manuals included with your computer may be reproduced or transcribed by any means or translated into any language without prior written permission of Lenovo The software interface and function and hardware configuration described in the manuals included with your computer might not match exactly the actual configuration of the computer that you purchase You are welcome to contact us about the manuals included with your computer For the latest information or any questions or comments contact or visit the Lenovo Web site Service Web site http support lenovo com User Guide 33 Trademarks Lenovo and the Lenovo logo are trademarks of Lenovo in the United States other countries or both Microsoft Windows and Windows Vista are trademarks of the Microsoft group of companies Intel Inside is a trademark of Intel Corporation in the U S and or other countries AMD the AMD Arrow logo ATI AMD Athlon AMD LIVE AMD Opteron AMD Phenom AMD Sempron Catalyst Cool n Quiet CrossFire PowerPlay Radeon and The Ulti
25. pending on the computer model and configuration L User Guide 1 O O O A RS RS RR SS SS O O A A RSS O SS SS SS SS 1 1 Front view of the chassis A Attention Be careful not to block any air vents on the computer Blocked air vents can cause overheating HR lenovo l E DO 00 a a Hard disk drive indicator Power button Optical Drive selected models only USB 2 0 connectors 2 Headphone connector Microphone connector Memory card reader selected models only DNOBEENE Optical drive eject button 2 User Guide 1 2 Rear view of the chassis If the rear view configuration shown in this chapter is different from the rear of your computer please refer to the rear of your computer BBRRBRBBRRBDBBRB OC Q E ESP OS OC AA BE 0AB D LE N OOO DO NA 0000 DOC 000 0000 SE OQO A ROROROROROR ZOROSOZOZOZOM So Sos osso Soo OBOSOGOGOGO EE PS 2 keyboard connector PS 2 mouse connector USB 3 0 connector Serial port VGA monitor connector USB 2 0 connectors 2 Ethernet connector Audio connectors Optional serial port Integrated cable lock Kensington lock slot
26. stem These recovery discs are used to boot your computer and will guide you through the entire restoration process In the Windows system click Start All Programs Lenovo Lenovo Rescue System After starting Rescue System click Create Recovery Disc to create a bootable recovery disc from the current system Follow the on screen prompts to create recovery discs 12 User Guide Troubleshooting and SSES Confirming Setup Y This chapter contains the following topics 9 gt Troubleshooting and Problem Resolution 9 in this manual is only used for the machines 0 which have the TV tuner card It does not O apply to those machines that do not have a O TV tuner card User Guide 13 SS SS US O A RO RSS RSS SS O SS O DS SS SS l l O Note The description of the TV tuner card l l L Solving Problems Follow these tips when troubleshooting your computer f you added or removed a part before the problem started review the installation procedures to ensure that the part is correctly installed f a peripheral device does not work ensure that the device is properly connected f an error message appears on the screen write down the exact message This message may help support personnel diagnose and fix the problem s f an error message occurs in a program see t
27. t have a TV card This guide contains procedures for replacing the following parts e Memory modules e Hard disk drive e Optical drive Safety information for replacing CRUs Do not open your computer or attempt any repair before reading the Important safety information in the Safety and Warranty Guide that was included with your computer H you no longer have this copy of the Safety and Warranty Guide you can obtain one online from the Support Web site at http support lenovo com 20 User Guide Additional information resources If you have Internet access the most up to date information for your computer is available from the World Wide Web You can find the following information CRU removal and installation information Publications Troubleshooting information Parts information Links to other useful sources of information To access this information go to http support lenovo com Tools required To disassemble the computer you need the following tools Wrist grounding strap and conductive mat for preventing electrostatic discharge Flat screwdriver Phillips screwdriver Hex screwdriver Plastic flat screwdriver Plastic tweezers O Note The screws for the different components vary in size During the disassembly procedure group the screws with their corresponding components to avoid a mismatch when replacing the components User Guide 21 Handling static sensitive devices Static electrici
28. to http www energystar gov Lenovo encourages you to make efficient use of energy an integral part of your day to day operations To help in this endeavor Lenovo has preset the following power management features to take effect when your computer has been inactive for a specified duration ENERGY STAR power management features by operating system Microsoft Windows XP Microsoft Windows Vista and Windows 7 e Turn off monitor After Power plan Balanced 15 minutes e Turn off the display After 10 minutes e Turn off hard disk drives Never e Put the computer to sleep After e System standby After 25 minutes 20 minutes e Advanced power settings e System hibernates Never Turn off hard disk drives After 20 minutes Hibernate Never To awaken your computer from a Sleep or System Standby mode press any key on your keyboard For more information about these settings refer to your Windows Help and Support information system Enabling ErP compliance mode You can enable the energy related products directive ErP compliance mode through the Power menu in the Setup Utility program This mode reduces electricity consumption when your computer is in standby mode or turned off To enable ErP compliance mode in the Setup Utility program do the following 1 Repeatedly press and release the F1 key when turning on the computer to start the Setup Utility program 2 From the Setup Utility program main menu select Power ErP an
29. tructions By selecting Control Panel Administrative Tools Computer Management Disk Management you can see the service partition which must not be deleted O Note The recovery files and relevant data used by the rescue system are saved in the service partition If the service partition is deleted or damaged by someone other than authorized Lenovo service personnel Lenovo will not be liable for any losses arising therefrom in any way 2 1 OneKey Recovery OneKey Recovery is an easy to use application You can use it to restore your computer to the system default or to a previously backed up state Detailed Operation Procedure 1 Repeatedly press and release the F2 key once turning on the computer until the Lenovo Rescue System open then select OneKey Recovery O Note System Recovery will overwrite all of the data on the C drive To prevent loss of data be sure to back up relevant data before performing system recovery 2 Follow the on screen instructions to select the backup task you want to restore from and the disk where you want to install the operating system then press Next to start the restore 3 Please wait during the process of system recovery Do not interrupt the operation during the recovery process 4 After the system is recovered successfully the software will prompt you to restart the computer Restart the computer and start the operating system 2 2 Driver and Application Installation The
30. ty is harmless to you but it can seriously damage computer components When you are replacing a part do not open the antistatic package containing the new part until the defective part has been removed from the computer and you are ready to install the new part Take these precautions to avoid static electricity damage when handling parts and other computer components Limit your movement Movement can cause staticelectricity to build up around you Always handle parts and other computer components carefully Handle adapters memory modules system boards and microprocessors by the edges Never touch any exposed circuitry Prevent others from touching the parts and other computer components Before you replace a new part touch the antistatic package containing the part to a metal expansion slot cover or other unpainted metal surface on the computer for at least two seconds This reduces static electricity in the package and your body When possible remove the new part from its antistatic packaging and install it directly into the computer without setting the part down When this is not possible place the antistatic package that the part came in on a smooth level surface and place the part on it Do not place the part on the computer cover or other metal surface 22 User Guide 4 1 Locations This section provides illustrations to help locate the various connectors controls and components of the computer To remove the comput
31. words for the Lenovo Rescue system 2 3 1 Launch Repeatedly press and release the F2 key once turning on the computer until the Lenovo Rescue System open then select System Setup 2 3 2 Network Settings Depending on the network access mode of the computer select ADSL or LAN Connection in the network connection modes 1 If you select ADSL input the username and password of the ADSL connection User Guide 11 2 If you select LAN connection configure the IP address and proxy server of the LAN 2 3 3 Password Management Password Management allows you to set and manage the password for Lenovo Rescue System The default password is blank Set a password when you access Password Management for the first time If you don t want to set a password access the system directly and operate it accordingly 2 4 System Backup This backs up your system partition to an image file In case of a system failure you can restore your system from this image file In the Windows system click Start All Programs Lenovo Lenovo Rescue System After starting Rescue System click System Backup to back up your system partition by following the prompts 2 5 System Recovery Reboot your computer into the system recovery environment You can choose to restore to a system backup point or the initial state factory default settings 2 6 Create Recovery Disc Create a bootable recovery disc from the current sy
Download Pdf Manuals
Related Search