Harbor Freight Tools 1000 lb. Capacity Engine Stand Product manual
Contents
1. arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state PITTSBURGH 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 33532. LEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages
3. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference PITTSB URGH Rez ITEM 69886 1000 Ib Engine Stand Visit our website at http www harborfreight com Email our technical support at tech harborfreight com When unpacking make sure that the product is intact and undamaged If any parts are missing or broken please call 1 800 444 3353 as soon as possible Copyright 2012 by Harbor Freight Tools All rights reserved s i No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assembly and service may not be included Specifications Weight Capacity 1 000 Ib Assembled Dimensions 34 3 4 L x 31 W x 36 H Face Plate 10 3 16 W x 6 H x 7 16 thick Wheel Diameter 3 x2 3 1 2 x2 Im
4. Pin 4 Handle QT SS Grip 1 Mounting 5 M 6 Washer 7 Handle 2 Mounting Plate 8 Mounting ia Plate 8 Column 5 Figure D Attach Mounting Plate and Handle Figure E Installing Arms and Locking Rotation 5 Insert Mounting Plate 8 shaft into the top of the Column 5 Insert the Handle 2 through the 6 Attach the Mounting Arms 9 to the Mounting Plate 8 and secure slots in the Mounting Plate 8 using the with the Cotter Pin 3 Bolts 10 Washers 7 and Nuts 6 7 To lock Mounting Plate 8 rotation align a hole on it with the hole on the top of the Column 5 and insert the Pin 4 PITTSBURGH Page 4 For technical questions please call 1 800 444 3353 Item 69886 Operating Instructions beginning of this document including all text under subheadings therein Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the before set up or use of this product Mounting Engine AWARNING TO PREVENT SERIOUS INJURY Before attaching an engine to the stand confirm that its weight does not exceed the Stand maximum capacity Remove the Pin 4 from the Column 5 5 2 Determine the thread type and length of bolts not included needed to thread into the engine block 6 Use grade 8 bolts that are long enough to fit through the Arms and thread as deeply as possible into the engine block 7 3 Align the Mounting Arms 9 with four mounting bolt locations
5. centered and secured to mounting attachments Page 2 For technical questions please call 1 800 444 3353 Item 69886 Assembly Instructions beginning of this document including all text under subheadings therein Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the before set up or use of this product Column 5 _ Rear Beam 23 Middle Beam 20 Lock Pa Washer 21 N Bolt 22 Figure A Attaching Column to Rear and Middle Beams 1 To attach the Column to the Rear and Middle Beams a Insert Middle Beam 20 into the receiver at the bottom of the Column 5 b Place the Rear Beam 23 against the Column Align the holes in all three parts and secure with a Bolt 22 and Lock Washer 21 Item 69886 For technical questions please call 1 800 444 3353 Middle Beam 20 Front Beam 11 o Nut 14 Washer 13 ye A Bolt 12 Figure B Attach Front Beam Use Bolts 12 Washers 13 and Nuts 14 to attach the Front Beam 11 to the Middle Beam 20 with the brackets on the bottom as shown Washer 25 Snap Ring 26 Bolt 15 1 Caster 19 Figure C Attach Wheels and Casters Attach Casters 19 to the Front Beam 11 using Bolts 15 Washers 16 Lock Washers 17 and Nuts 18 Slide a Wheel 24 onto each axle at end of Rear Beam 23 Then slide on a Washer 25 and secure with a Snap Ring 26 Page 3 Cotter Pin 3
6. on the engine 8 WARNING Use all four Arms when attaching an engine to the Stand 4 Place the bolts not included through the Mounting Plate 8 side and securely tighten them into the engine The bolt heads must press against the back of the Arms if needed use flat washers not included as spacers Rotating Engine AWARNING and the engine to prevent it from accidental rotation remove Pin 4 Removing Engine 1 With assistance rotate the 3 engine to its initial position 2 Secure the engine properly to the crane Use the crane to support all of the engine s weight directly overhead but do not start lifting the engine stand Item 69886 For technical questions please call 1 800 444 3353 Tighten the Bolts 10 and Nuts 6 that hold the Mounting Arms 9 to the Mounting Plate 8 securely Slowly lower the hoist engine crane sold separately until all the engine s weight is held by the stand Safely release the engine from the hoist engine crane Slowly rotate the engine to the desired angle and insert the Pin 4 into the top of the Column 5 TO PREVENT SERIOUS INJURY Be prepared for sudden engine movement before removing Pin Stay clear of engine 1 While holding onto the Handle 2 2 Use assistance to rotate the engine to the desired angle and insert the Pin 4 into the top of the Column 5 Once the engine is properly supported by the crane remove the bolts securing the M
7. ounting Arms 9 to the engine Page 5 Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician AWARNING TO PREVENT SERIOUS INJURY FROM STAND FAILURE Do not use damaged equipment Make sure the stand is stable If any unsafe conditions are found take it to a qualified technician for service or repair 1 BEFORE EACH USE inspect the general condition of the Stand Check it for cracks bends in the metal signs of unusual wear or any other condition that may affect its safe operation If any are found do not use the Stand 2 Keep Engine Stand clean and free of dirt or grease 3 Before each use check that hardware is securely fastened Check that the Casters are clean and turn properly AFTER USE clean external surfaces of the stand with a clean moist cloth PITTSBURGH Page 6 For technical questions please call 1 800 444 3353 Item 69886 Parts List and Diagram 6 NutMi2 4 15 BoltMex20_ 8 16 Washers 8 8 Mounting Plate 1 17 LockWasher8_ 8 9 MountingArm 4 148 NutMe 8 Note Some parts are listed and shown for illustration purposes only and are not i available individually as replacement parts Sj Record Serial Number Here 1 154 Note If product has no serial number record month and year of purchase instead Item 69886 For technical questions please call 1 800 444 3353 Page 7 P
8. portant Safety Information Assembly Precautions 1 Assemble only according to these 4 Keep bystanders out of the instructions Improper assembly area during assembly can create hazards 5 Do not assemble when tired 2 Wear ANSI approved safety goggles or when under the influence and heavy duty work gloves of drugs or medication during assembly 6 Weight capacity and other product 3 Keep assembly area clean and well lit capabilities apply to properly and completely assembled product only Use Precautions Failure to heed these instructions may result in personal injury and or property damage 1 Study understand and follow all 7 Wear ANSI approved safety goggles instructions before operating this device and heavy duty work gloves during use 2 Do not exceed rated capacity 8 Do not use for aircraft purposes Be aware of dynamic loading 9 Inspect before every use Sudden load movement may briefly create excess load causing product failure 10 This product is not a toy Do not allow children to play with or near this item do not use if parts loose or damaged Use only on hard level surfaces 11 Use as intended only gt Lock mounting plate rotating mechanism before applying a load 12 Maintain product labels and nameplates These carry important safety information If unreadable or missing contact Harbor Freight Tools 6 Hold Handle while removing the Pin for a replacement 5 Assure load is
Download Pdf Manuals
Related Search